Mechanical engineering | Vehicles » Gearshift

• 25 Gearshift Page 25 11 OOO Removing and lnstalling Gearshift Lever 25-11 /1 011 Replacing Rubber Rings ln Gearshift Lever •. • •• •• 11/1 041 Replacing Gearshift Lever Ball Shells ••. ••••• •••••• • •••••• ••••••• •••••• • 11/2 081 Replacing Gearshift Lever Bel ]0111s . •• • • • • • • •••• 11/2 200 Removing and lnstalling Gearshift Lever Mounting Plate . • • •• 11/3 25 16 050 Removing and lnstalling Selector Lever 111ith Base .• •••••• 16/1 061 Rep 1ac ing Se1ector Lever Hand le • . • • • • • • 16/2 075 Replaci ng Selector Lever Linkage . ••••••••••• 16/2 080 Removing and lnstalling Selector Lever . 16/2 211 Replac ing Selector Rod Bushing . • ••••• 16/+ 551 Replacing Se lector

Lever Bearing Bushings . 16/4 581 Replacing Shifting Gate . • 16/5 • • • 6.76 25-0/1 • 25 11 OOO REMOVING ANO INSTALLING GEARSHIFT LEVER Remove circlip (1) . Take off washer (2) . Pull out selector rod (3) . Push up bellows. Remove circlip {4) . Remove gearshift lever. • lnstallation Note! Lubricate ball shells with Longterrn 2. 25 11 011 REPLACING RUBBER RINGS IN GEARSH IFT LEVER Rernove gearshift lever - 25 11 OOO. Remove wire snap ring • • 316 25 003 Pull gearshitt lever off of gearshitt lever base. Remove lockwasher. Remove rubber rings . • 316 25 004 6.76 25-11 /1 25 11 041 REPLACING GEARSHIFT LEVER BALL SHELLS Remove gearshitt lever - 25 11 OOO. Take out wire snap ring . • 316 25 003 Wire snap ring (1) , circlip (2) , spr ing retainer (3), spring (4), ball shell (5 and 6), washer (7) . lnstallation Note! Lubricate ball shells with Longterm 2. • 316 25 005 25 11 081 REPLACING GEARSHIFT LEVER BELLOWS Unscrew knob on

gearshift lever. • Remove bellows. 25-11/2 • • 25 11 200 REMOVING ANO INSTALLING GEARSHIFT LEVER MOUNT ING PI.ATE Remove and install gearshift lever - 25 11 OOO. Unscrew mounting plate socket head cap screws. Remove heat guard. Oetach center bearing at body . • lnstallation Note! Preload center bearing in forward direction with 2 mm (0.079") (A) • Oetach mounting bracket . • Remove mounting plate. lnstallation Note ! Check rubber bearing for wear, replace if necessary • • 316 25 0 11 6.76 25-11/3 • 25 16 050 REM 0VINGANO INSTALLINGSELECT0R LEVER W1THBASE Remove lock . Detach selector rod . 316 2 5 012 Unscrew brush plate and cover mounting screws. Remove cover with brush plate . • Remove sel ector lever mask plate . • Oisconnect transmission switch plug . Unscrew base mounting bolts and remove base . • 6.76 25-16/1 lnstallation Note! lf car has an air conditioner, install tapered plate {A) in addit ion to insulator • •

25 16 061 REPI.ACING SELECT0R LEVER HANDLE Move se 1ector le ver to 11R11 • Loosen hollow set screw . Remove handle . • lnstallation Note! lnserl release catch pin ín selector linkage hole. • 25 16 075 REPI.AClNG SELECTOR LEVER LINKAGE 25 16 080 REM0VING AND INSTALLING SELECT0R LEVER Remove selector lever with base - 25 16 050. Remove selector lever handle - 25 16 061 . 0rive out pin. 316 25 019 25-16/2 • • Pull out selector lever base and remove washer as well as bearing bushings . lnstallation Note! Lubricate bushings with Longterm 2. I ~ 1 -. J 316 2].120 Loosen range light bulb holder mounting screw. Li ft wire out of selector lever s upper section and disconnect plug at base • . · • ·. . .4 t ·t tii . , wr•, L~ , J 316 25 021 Loosen transmission switch mounting screw and take out transmission switch together with top section of selector lever from base . lnstall ation Note! Note position of transmission switch driving dog . • 316 25

022 Take selector linkage with spring out of top section of selector lever • • 816 25023 6.76 25-1 6/3 25 16 211 REPlJCING SELECTOR ROD BUSH ING Remove lock. Oetach selector rod . lnstall ation Note! Adjust selector rod - 24 00 004. • 316 25 012 Lift bushing out of lower section of selector lever. lnstallation Note! Lubricate bushing with Longterm 2. • 25 16 551 REPlJC ING SELECTOR LEVER BEARING BUSHINGS - Selector Lever with Base Removed Drive out pin. • 316 25 019 Pull out lower section of selector lever and remove washer as well as bearing bushings. lnstallation Note! Lubricate bushings with Longterm 2. 25-1 6/4 • • 25 16 581 REPLACING SHIFTING GATE - Selector lever with Base Removed Remove selector lever upper and lower sections 25 16 080. Loosen shifting gate mounting screws and take gate off of base . 316 25 025 • • • 6.76 25-16/5