Hadászat | Tanulmányok, esszék » COMNAVAIRFORINST 4790.2C Chapter 16, Intermediate Level (I-Level) Maintenance Data System (MDS) Functions, Responsibilities and Source Document Procedures

Adatlap

Év, oldalszám:2017, 293 oldal
Nyelv:angol
Letöltések száma:3
Feltöltve:2020. június 01
Méret:9 MB
Intézmény:-

Csatolmány:-

Letöltés PDF-ben:Kérlek jelentkezz be!

Értékelések

Ezt a doksit egyelőre még senki sem értékelte. Legyél Te az első!


Új értékelés

Tartalmi kivonat

COMNAVAIRFORINST 4790.2C 15 Jan 2017 CHAPTER 16 Intermediate Level (I-Level) Maintenance Data System (MDS) Functions, Responsibilities and Source Document Procedures Table of Contents 16.1 I-Level Maintenance Data System (MDS) Functions and Responsibilities 1 16.11 Production Control 1 16.111 Assigning Job Control Number (JCN) 1 16.112 Work Center Workload Reports 2 16.113 NALCOMIS Maintenance Action Form (MAF) and Naval Tactical Command Support System (NTCSS) Optimized Organizational Maintenance Activity (OOMA) NALCOMIS Configuration Management Auto Log Set (CM ALS) Records Flow . 2 16.114 Controlling Awaiting Maintenance 6 16.115 Maintenance Reports 6 16.116 Interface Requirements 6 16.12 Production Division Officers Responsibilities 7 16.13 Work Center Supervisors 7 16.131 Introduction 7 16.132 Communication 8 16.133 Machine Reports 8 16.134 Data Accuracy 8 16.135 Work Center Workload Report 9 16.136 NALCOMIS Automated Procedures 9 16.137 Material Requisitioning 9

16.138 High Usage Piece Parts Available in the Pre-Expended Bin (PEB) 10 16.139 Tool Control in the Work Center 10 16.14 Maintenance Information Systems (MIS) 11 16.141 NALCOMIS Procedures 11 16.142 IRIL Procedures 11 16.143 SESS and NALCOMIS 12 16.144 Historical Files 12 16.15 VIDS Operation 12 16.151 VIDS Board 12 16-i COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.152 VIDS Board Layout (Figure 16-10) 12 16.153 VIDS Board Verification 13 16.154 VIDS/MAF Flow; Off-Equipment Work 13 16.2 I-Level Maintenance Source Document Procedures 15 16.21 Maintenance Action Documentation Procedures 15 16.211 Types of Maintenance Action Form (MAF) Maintenance Actions 15 16.212 Intermediate Document Flow 16 16.213 Data Field Description 17 16.22 Support Equipment (SE), Training Devices, Missile Target Documentation 24 16.221 Documentation Collection Method 24 16.222 Terms and Data Field Definitions 24 16.223 SE Maintenance Actions 24 16.224 Support Equipment (SE) Repair Action 25

16.225 Support Equipment (SE) Inspections and Periodic Maintenance 25 16.226 Support Equipment (SE) Corrosion Documentation 26 16.227 Support Equipment (SE) Preservation and Depreservation 26 16.228 Support Equipment (SE) Technical Directive (TD) Compliance 26 16.229 Support Equipment (SE) Inventory Reporting Procedures 27 16.2210 Change of Reporting Custodian 29 16.2211 Calibration Actions 29 16.23 Aeronautical Component and Item Documentation Procedures 29 16.231 Component Repair 29 16.232 Maintenance Action Form (MAF) Work Request 33 16.233 Technical Directive (TD) Compliance 34 16.234 Recovery and Reclamation of Crash Damaged Aircraft 35 16.24 I-Level Engine, Auxiliary Power Unit (APU), and Support Equipment Gas Turbine Engine (SEGTE) Maintenance Documentation Procedures . 35 16.241 Documentation Procedures 35 16.242 Documentation Procedures Exceptions 35 16.243 Engine, APU, and SEGTE Corrosion Documentation 36 16.244 Corrosion Prevention Requirements 36 16.245 Corrosion

Treatment Requirements 36 16.246 All Unscheduled Corrosion Prevention 36 16.247 Unscheduled Corrosion Treatment 36 16-ii COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.248 Engine Repair 36 16.249 Major Engine Inspections 37 16.2410 Technical Directive (TD) Compliance 37 16.2411 Modular Engine Repair 38 16.2412 Modular Engine Major Inspections 38 16.2413 Modular Engine Technical Directive (TD) Compliance 38 16.2414 Engine or Module Component Cannibalization Actions for the I-Level Activities 39 16.2415 Cartridges (CARTs), Cartridge Actuated Devices (CADs), and Propellant Actuated Devices (PADs) Documentation . 39 16.25 Documentation Explanations 40 16.251 End Item Repair (No Removed Component) 40 16.252 End Item Repair of a SEGTE (No Removed Component) 40 16.253 End Item Repair (Removed Repairable Component) 41 16.254 Facilitate Other Maintenance (FOM) Action 42 16.255 Primary Work Center Repair Action 42 16.256 Assisting Work Centers (Same WUC) 43 16.257 Assisting Work

Centers (Different WUC) 44 16.258 On-Equipment Cannibalization 44 16.259 Support Equipment (SE) Turned-In by a Supported Activity for Scheduled or Unscheduled Maintenance (Excluding PME) . 45 16.2510 Turn-In Document Off-Equipment Repair 46 16.2511 Turn-In Document SEGTE Repair 46 16.2512 Off-Equipment Component Repair 47 16.2513 Suffix Turn-In Document 47 16.2514 Off-Equipment Subassembly Repair 48 16.2515 Inspection Control Document 49 16.2516 Inspection Look Phase Supporting Document 49 16.2517 Inspection Fix Phase Document 50 16.2518 End Item TD Compliance (No Removal Component) 51 16.2519 TD Compliance Supporting VIDS/MAF 52 16.2520 TD Compliance Turn-In Document 52 16.2521 Off-Equipment TD Compliance Action 53 16.2522 TD Compliance Removal (On-Equipment) 54 16.2523 Inventory Transaction (Gain) 54 16-iii COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2524 Inventory Transaction (Loss) 55 16.2525 Removed Component for Calibration 56 16.2526 Component Turn-In Document

56 16.2527 BCM Action (AMSU) 57 16.2528 Troubleshooting Close Out 57 16.2529 Assisting Work Center (Same WUC) 58 16.2530 Assisting Work Center (Different WUC) 59 16.2531 Component Repaired Using a Repairable Subassembly 59 16.2532 Subassembly/Module Repair (Suffix) 60 16.2533 Sub-Subassembly/Module Repair (Double Suffix) 61 16.2534 Cannibalization (End Item) 62 16.2535 Cannibalization (From AWP Component) 62 16.2536 Cannibalization (Off-Equipment) 63 16.2537 Matched Set (Repair and No Repair) 64 16.2538 Tire and Wheel Documentation (Tires Prepositioned in W/C and Ordering Replacement Tire) . 65 16.2539 Transferring IMA Close Out (Post/Predeployment) 65 16.2540 Receiving IMA (Reinitiation Documentation) 66 16.2541 Component Missing SRC Card 67 16.2542 Corrosion Supporting MAF 67 16.2543 Turn-In from Supply for TD Compliance 68 16.2544 VIDS/MAF Work Request (Production Control Entries) 68 16.2545 VIDS/MAF Work Request (Local Manufacture/Fabrication) 69 16.2546 VIDS/MAF Work

Request (Supply Asset Build-Up Induction) 70 16.2547 Scheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) 70 16.2548 Scheduled Maintenance Work Request (NDI On-Site) (Passed Inspection) 71 16.2549 Scheduled Maintenance Work Request (NDI On-Site) (Failed Inspection) 72 16.2550 Scheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) 72 16.2551 Unscheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) 73 16.2552 Unscheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) 74 16.2553 O-Level Armament Equipment Turn-In for Scheduled Maintenance 74 16.2554 O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (No Material Required) (Completed) . 75 16-iv COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2555 O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (Maintenance and Material Required) (Completed). 76 16.2556 Turn-In Acceptance/Functional Check on Armament Equipment 76 16.2557 Turn-In

Acceptance/Functional Check on Armament Equipment (Completed) 77 16.2558 Armament Equipment Pool Preservation/Depreservation Control Document (Completed). 78 16.2559 I-Level Armament Equipment Pool Component Due for Scheduled Maintenance (Completed). 78 16.2560 O-Level ALSS Equipment Due for Scheduled Maintenance (Maintenance and Material Required) (Completed) . 79 16.2561 O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Completed) 80 16.2562 O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Maintenance and Material Required) (Completed) . 80 16.2563 I-Level ALSS Pool Component Due for Scheduled Maintenance (Completed) 81 16.2564 MAF Discrepancy (Supply Asset Induction Document) (Material Condition Tag Missing). 82 16.2565 Completed Discrepancy MAF (Supply Asset Induction Document) (Material Condition Tag Missing) . 82 16.2566 TD Compliance Turn-In Document (O-Level) 83 16.2567 TD Compliance (IMA Assist) 84 16.2568 Turn-In for TD Compliance 85

16.2569 IMA TD Compliance 85 16.2570 TD Compliance Removal 86 16.2571 O-Level Turn-In Control Document for Engine Repair 87 16.2572 Supply Asset Engine Depreservation 87 16.2573 Supply Asset Engine (Assist MAF) Test Cell Run 88 16.2574 Fix-In-Place (Material Not Required) 88 16.2575 Fix-In-Place (Material Required) 89 16.2576 Removal/Replacement of a Tracked Consumable Component 89 16.2577 Removal/Replacement of a Repairable Component with No Repairable SubSubassemblies 90 16.2578 Removal/Replacement of a Repairable Component with Repairable Sub- Subassemblies . 91 16.2579 Facilitate Other Maintenance (FOM) 91 16-v COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2580 Engine Repair Control Document (Completed VIDS/MAF) 92 16.2581 Supply Asset Engine Build-Up 93 16.2582 Engine Component Turn-In for Repair 93 16.2583 Engine Component Repair (Completed) 93 16.2584 Turn-In Document Solely for Major Engine Inspection 94 16.2585 Control Document Solely for Major Engine

Inspection (Completed) 94 16.2586 Control Document for Major Engine Inspection (Engine Undergoing Repair) 95 16.2587 Major Engine Inspection (Look Phase Supporting Work Center) 95 16.2588 Major Engine Inspection (Fix-In-Place) 96 16.2589 Major Engine Inspection (Fix Phase Removal and Replacement of a Repairable Component) . 97 16.2590 Major Engine Inspection (Component Turn-In) 97 16.2591 Major Engine Inspection Completed After Repair Action 98 16.2592 Supply Asset (TD Compliance Request) 98 16.2593 Supply Asset TD Compliance Request (IMA Production Control Entries) 99 16.2594 Supply Asset (TD Compliance Completed) 99 16.2595 O-Level Engine TD Compliance Request 100 16.2596 O-Level Engine TD Compliance Request (Production Control Entries) 100 16.2597 O-Level Engine TD Compliance Request (Completed) 101 16.2598 I-Level Originated TD Compliance Request (Engine Component) 102 16.2599 I-Level Originated TD Compliance (Completed) 102 16.25100 O-Level Request for TD Compliance

Assist (Engine Component) 103 16.25101 O-Level Request for TD Compliance Assist (AMSU/Production Control Entries) . 104 16.25102 O-Level Request for TD Compliance Assist (Completed) 104 16.25103 O-Level Turn-In Control Document for Engine Repair (Modular Engine) 105 16.25104 Fix-In-Place (Not Requiring Material) 105 16.25105 Fix-In-Place (Requiring Material) 106 16.25106 Removal/Replacement of a Repairable Subassembly with No Repairable SubSubassemblies 107 16.25107 Removal/Replacement of a Repairable Module/Component with Repairable SubSubassemblies 107 16.25108 Engine Repair Control Document (Completed) 108 16.25109 Turn-In of Repairable Module with Repairable Sub-Subassemblies 109 16-vi COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25110 Removal/Replacement of a Repairable Sub-Subassembly from a Module 109 16.25111 Module Repair (Completed) 110 16.25112 Turn-In of Repairable Sub-Subassembly from a Repairable Component 110 16.25113 Repair of a Repairable Component with

Required Material 111 16.25114 Turn-In of a Repairable Component Sub-Subassemblies 111 16.25115 Repair of a Sub-Subassembly from a Component Subassembly (Completed) 112 16.25116 Removal/Replacement of a Repairable Sub-Subassembly from a Module 112 16.25117 Turn-In of a Repairable Sub-Subassembly from a Module 113 16.25118 O-Level Turn-In Control Document Modular Engine Turn-In (Solely for Major Engine Inspection). 113 16.25119 Major Modular Engine Inspection (Look Phase Supporting Work Center) 114 16.25120 Major Modular Engine Inspection (Look Phase Supporting Work Center) (Engine Test Cell Run) . 114 16.25121 Major Engine Inspection (Fix-In-Place) 115 16.25122 Major Engine Inspection (Fix Phase Module Replacement) 116 16.25123 Major Engine Inspection (Module Turn-In) 116 16.25124 Major Engine Inspection (Fix Phase Repairable Component Replacement) 117 16.25125 Major Engine Inspection (Fix Phase Component Turn-In) 117 16.25126 Completed Major Inspection Control Document

(Modular Engine Turned-In Solely for Major Inspection) . 118 16.25127 O-Level Activity Request for a Modular Engine TD Compliance by I-Level Activity . 118 16.25128 Production Control Entries (O-Level Activity Request for TD Compliance) 119 16.25129 Completed TD Compliance (Applies to a Module With No Module or Repairable Component P/N Change) . 119 16.25130 TD Compliance (Applies to a Module With P/N Change) 120 16.25131 TD Compliance (Applies to a Component Within A Module) 121 16.25132 Engine or Module Cannibalization (For A Supported Activity) 122 16.25133 Removal and Replacement of Cartridges (CART), Cartridge Activated Devices (CAD), and Propellant Actuated Devices(PAD) (I-Level Maintenance) . 122 16.25134 Fleet Readiness Centers (FRC) NALCOMIS Optimized Intermediate Activity (OIMA) Documentation Procedures and Processes . 123 Figure 16-1: JCN Suffix Logic Table . 129 Figure 16-2: Example of JCN Suffix Selection. 130 16-vii COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure

16-3: Workload Inquiry . 131 Figure 16-4: Off-Equipment Documentation Flow . 132 Figure 16-5: On-Equipment Work Initiated by I-level Documentation Flow . 133 Figure 16-6: Unserviceable Label-Material (DD 1577-2). 134 Figure 16-7: IRIL Board . 135 Figure 16-8: Pocket Indicator Strips and Locator Tabs . 136 Figure 16-9: SE Transfer Report (Sample) . 137 Figure 16-10: VIDS Board Layout. 138 Figure 16-11: Off-Equipment VIDS/MAF Flow . 139 Figure 16-12: Types of VIDS/MAFs Used for SE, Training Devices, and Missile Target Documentation . 140 Figure 16-13: End Item Repair (No Removed Component) . 141 Figure 16-14: End Item Repair of a SEGTE (No Removed Component). 142 Figure 16-15: End Item Repair (Removed Repairable Component) . 143 Figure 16-16: Facilitate Other Maintenance Action. 144 Figure 16-17: Primary Work Center Repair Action . 145 Figure 16-18: Assisting Work Centers (Same WUC) . 146 Figure 16-19: Assisting Work Centers (Different WUC) . 147 Figure 16-20: On-Equipment

Cannibalization . 148 Figure 16-21: Support Equipment Turned-In by a Supported Activity for Scheduled Maintenance (Excluding TMDE). 149 Figure 16-22: Support Equipment Turned-In by a Supported Activity for Unscheduled Maintenance (Excluding TMDE) 149 . 150 Figure 16-23: Turn-In Document (Off-Equipment Repair) . 151 Figure 16-24: Turn-In Document SEGTE Repair . 152 Figure 16-25: Off-Equipment Component Repair . 153 Figure 16-26: Suffix Turn-In Document . 154 Figure 16-27: Off-Equipment Subassembly Repair . 155 Figure 16-28: Inspection Control Document. 156 Figure 16-29: Inspection Look Phase Supporting Document . 157 Figure 16-30: Inspection Fix Phase Document . 158 Figure 16-31: End Item TD Compliance (No Removal Component) . 159 Figure 16-32: TD Compliance Supporting VIDS/MAF. 160 Figure 16-33: TD Compliance Turn-In Document . 161 16-viii COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-34: Off-Equipment TD Compliance Action . 162 Figure 16-35: TD Compliance Removal (On-Equipment).

163 Figure 16-36: VIDS/MAF Required for End Item TD Compliance Concurrent with a Failed Part . 164 Figure 16-37: VIDS/MAF Required for Component TD Compliance . 165 Figure 16-38: VIDS/MAF Required for End Item TD Compliance Concurrent With a Failed Part . 166 Figure 16-39: VIDS/MAF Required for Component TD Compliance With a Failed Part . 167 Figure 16-40: Inventory Transaction (Gain) . 168 Figure 16-41: Inventory Transaction (Loss) . 169 Figure 16-42: Removed Component for Calibration . 170 Figure 16-43: Component Turn-In Document . 171 Figure 16-44: BCM Action (AMSU) . 172 Figure 16-45: Troubleshooting Close Out. 173 Figure 16-46: Assisting Work Center (Same WUC). 174 Figure 16-47: Assisting Work Center (Different WUC) . 175 Figure 16-48: Component Repaired Using a Repairable Subassembly . 176 Figure 16-49: Subassembly/Module Repair (Suffix) . 177 Figure 16-50: Sub-Subassembly/Module Repair (Double Suffix) . 178 Figure 16-51: Cannibalization (End Item) . 179 Figure 16-52:

Cannibalization (From AWP Component) . 180 Figure 16-53: Cannibalization (Off-Equipment) . 181 Figure 16-54: Matched Set (Repair). 182 Figure 16-55: Matched Set (No Repair) . 183 Figure 16-56: Tire and Wheel Documentation (Tires Prepositioned in W/C) . 184 Figure 16-57: Tire and Wheel Documentation (Ordering Replacement Tire) . 185 Figure 16-58: Transferring IMA Close Out (Post/Predeployment) . 186 Figure 16-59: Receiving IMA (Reinitiation Documentation) . 187 Figure 16-60: Component Missing SRC Card . 188 Figure 16-61: Corrosion Supporting MAF. 189 Figure 16-62: Turn-In from Supply for TD Compliance . 190 Figure 16-63: VIDS/MAF Work Request (Production Control Entries) . 191 Figure 16-64: VIDS/MAF Work Request (Local Manufacture/Fabrication). 192 Figure 16-65: VIDS/MAF Work Request (Supply Asset Build-Up Induction) . 193 16-ix COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-66: Scheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) . 194 Figure 16-67: Scheduled

Maintenance Work Request (NDI On-Site) (Passed Inspection). 195 Figure 16-68: Scheduled Maintenance Work Request (NDI On-Site) (Failed Inspection) . 196 Figure 16-69: Scheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) . 197 Figure 16-70: Unscheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) . 198 Figure 16-71: Unscheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) . 199 Figure 16-72: O-Level Armament Equipment Turn-In for Scheduled Maintenance . 200 Figure 16-73: O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (No Material Required) (Completed) . 201 Figure 16-74: O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (Maintenance and Material Required) (Completed). 202 Figure 16-75: Turn-In Acceptance/Functional Check on Armament Equipment . 203 Figure 16-76: Turn-In Acceptance/Functional Check on Armament Equipment (Completed) . 204 Figure 16-77: Armament Equipment Pool

Preservation/Depreservation Control Document (Completed) . 205 Figure 16-78: I-Level Armament Equipment Pool Component Due for Scheduled Maintenance (Completed) . 206 Figure 16-79: O-Level ALSS Equipment Due for Scheduled Maintenance (Maintenance and Material Required) (Completed) . 207 Figure 16-80: O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Completed) . 208 Figure 16-81: O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Maintenance and Material Required) (Completed). 209 Figure 16-82: I-Level ALSS Pool Component Due for Scheduled Maintenance (Completed) . 210 Figure 16-83: VIDS/MAF Discrepancy (Supply Asset Induction Document) (Material Condition Tag Missing). 211 Figure 16-84: Completed Discrepancy VIDS/MAF (Supply Asset Induction Document) (Material Condition Tag Missing). 212 Figure 16-85: TD Compliance Turn-In Document (O-Level) . 213 Figure 16-86: TD Compliance (IMA Assist) . 214 Figure 16-87: Turn-In for TD Compliance . 215 Figure 16-88: IMA TD

Compliance. 216 Figure 16-89: TD Compliance Removal . 217 Figure 16-90: O-Level Turn-In Control Document for Engine Repair . 218 16-x COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-91: Supply Asset Engine Depreservation . 219 Figure 16-92: Supply Asset Engine (Assist VIDS/MAF) Test Cell Run . 220 Figure 16-93: Fix-In-Place (Material Not Required) . 221 Figure 16-94: Fix-In-Place (Material Required) . 222 Figure 16-95: Removal/Replacement of a Tracked Consumable Component . 223 Figure 16-96: Removal/Replacement of a Repairable Component with No Repairable SubSubassemblies . 224 Figure 16-97: Removal/Replacement of a Repairable Component with Repairable SubSubassemblies . 225 Figure 16-98: Facilitate Other Maintenance . 226 Figure 16-99: Engine Repair Control Document (Completed VIDS/MAF) . 227 Figure 16-100: Supply Asset Engine Build-Up . 228 Figure 16-101: Engine Component Turn-In for Repair . 229 Figure 16-102: Engine Component Repair (Completed) . 230 Figure 16-103: Turn-In

Document Solely for Major Engine Inspection . 231 Figure 16-104: Control Document Solely for Major Engine Inspection (Completed). 232 Figure 16-105: Control Document for Major Engine Inspection (Engine Undergoing Repair) . 233 Figure 16-106: Major Engine Inspection (Look Phase Supporting Work Center). 234 Figure 16-107: Major Engine Inspection (Fix-In-Place) . 235 Figure 16-108: Major Engine Inspection (Fix Phase Removal and Replacement of a Repairable Component) . 236 Figure 16-109: Major Engine Inspection (Component Turn-In) . 237 Figure 16-110: Major Engine Inspection Completed After Repair Action . 238 Figure 16-111: Supply Asset (TD Compliance Request) . 239 Figure 16-112: Supply Asset TD Compliance Request (IMA Production Control Entries) . 240 Figure 16-113: Supply Asset (TD Compliance Completed) . 241 Figure 16-114: O-Level Engine TD Compliance Request . 242 Figure 16-115: O-Level Engine TD Compliance Request (Production Control Entries) . 243 Figure 16-116: O-Level Engine TD

Compliance Request (Completed) . 244 Figure 16-117: I-Level Originated TD Compliance Request (Engine Component) . 245 Figure 16-118: I-Level Originated TD Compliance (Completed) . 246 Figure 16-119: O-Level Request for TD Compliance Assist (Engine Component) . 247 Figure 16-120: O-Level Request for TD Compliance Assist (AMSU/Production Control Entries) . 248 16-xi COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-121: O-Level Request for TD Compliance Assist (Completed) . 249 Figure 16-122: O-Level Turn-In Control Document for Engine Repair (Modular Engine) . 250 Figure 16-123: Fix-In-Place (Not Requiring Material) . 251 Figure 16-124: Fix-In-Place (Requiring Material) . 252 Figure 16-125: Removal/Replacement of a Repairable Subassembly with No Repairable SubSubassemblies . 253 Figure 16-126: Removal/Replacement of a Repairable Module/Component with Repairable SubSubassemblies . 254 Figure 16-127: Engine Repair Control Document (Completed) . 255 Figure 16-128: Turn-In of Repairable

Module with Repairable Sub-Subassemblies . 256 Figure 16-129: Removal/Replacement of a Repairable Sub-Subassembly from a Module . 257 Figure 16-130: Module Repair (Completed) . 258 Figure 16-131: Turn-In of Repairable Sub-Subassembly from a Repairable Component . 259 Figure 16-132: Repair of a Repairable Component with Required Material . 260 Figure 16-133: Turn-In of a Repairable Component Sub-Subassemblies. 261 Figure 16-134: Repair of a Sub-Subassembly from a Component Subassembly (Completed) . 262 Figure 16-135: Removal/Replacement of a Repairable Sub-Subassembly from a Module . 263 Figure 16-136: Turn-In of a Repairable Sub-Subassembly from a Module . 264 Figure 16-137: O-Level Turn-In Control Document Modular Engine Turn-In (Solely for Major Engine Inspection) . 265 Figure 16-138: Major Modular Engine Inspection (Look Phase Supporting Work Center) . 266 Figure 16-139: Major Modular Engine Inspection (Look Phase Supporting Work Center) (Engine Test Cell Run) . 267 Figure 16-140:

Major Engine Inspection (Fix-In-Place) . 268 Figure 16-141: Major Engine Inspection (Fix Phase Module Replacement) . 269 Figure 16-142: Major Engine Inspection (Module Turn-In) . 270 Figure 16-143: Major Engine Inspection (Fix Phase Repairable Component Replacement) . 271 Figure 16-144: Major Engine Inspection (Fix Phase Component Turn-In) . 272 Figure 16-145: Completed Major Inspection Control Document (Modular Engine Turned-In Solely for Major Inspection) . 273 Figure 16-146: O-Level Activity Request for a Modular Engine TD Compliance by I-Level Activity . 274 Figure 16-147: Production Control Entries (O-Level Activity Request for TD Compliance) . 275 16-xii COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-148: Completed TD Compliance (Applies to a Module With No Module or Repairable Component P/N Change). 276 Figure 16-149: TD Compliance (Applies to a Module With P/N Change) . 277 Figure 16-150: TD Compliance (Applies to a Component Within A Module) . 278 Figure 16-151: Engine or

Module Cannibalization (For a Supported Activity) . 279 Figure 16-152: Removal and Replacement of Cartridges, Cartridge Activated Devices, and Propellant Actuated Devices (I-Level Maintenance) . 280 16-xiii COMNAVAIRFORINST 4790.2C 15 Jan 2017 CHAPTER 16 Intermediate Level (I-Level) Maintenance Data System (MDS) Functions, Responsibilities and Source Document Procedures 16.1 I-Level Maintenance Data System (MDS) Functions and Responsibilities 16.11 Production Control 16.111 Assigning Job Control Number (JCN) The JCN is a 9, 10, or 11 character number that serves as a base for Monthly Data Report (MDR) and Maintenance Control procedures. The JCN allows for separate identification of each maintenance action, and provides a link with maintenance actions performed by the IMA in support of an organization. The JCN is composed of four parts: 16.1111 Organization (ORG) Code This is a three-character alphanumeric code that identifies an organization. It is used in the JCN to identify the

organization that originally assigns a JCN to a maintenance action. In the case of transient aircraft maintenance, the JCN will contain the ORG code of the aircraft reporting custodian. When an activity is assigned more than one ORG code, for example, separate codes assigned to Operations Department and Aircraft Intermediate Maintenance Department or Detachment (AIMD), the ORG code of the department directly responsible for O-level maintenance will be used in the JCN on all source documents for aircraft and equipment assigned to the activity. The general format structure of ORG codes is in Appendix E. NOTE: All supported organization codes must reside in the Naval Aviation Logistics Command Management Information System (NALCOMIS) database. 16.1112 Day This is a three-character numeric code specifying the day of the year The JCN day differs from the Julian date because the first position, identifying the year, is omitted. This is the date the JCN was assigned to a maintenance action

and does not necessarily reflect the date on which the work was actually started. 16.1113 Serial Number The serial number is either a three character number that runs sequentially from 001 to 999, or a three character alphanumeric number. This number is normally assigned in sequence as new jobs are initiated, for example, 001, 002, and 003. When 999 has been assigned, the next number in sequence will be 001. Alphanumeric serial numbers are used only when documenting inspections other than turnaround, daily, special, conditional, corrosion, acceptance, and transfer. Alphanumeric JCN structure will be as follows (exclusive of I-level and O-level): LOOK A00 thru Z00 to AA0 thru ZZ FIX A01 thru A99 Z01 thru Z99 AA1 thru AA9 thru AAA thru AAZ ZZ1 thru ZZ9 thru ZZA thru ZZZ 16.1114 Suffix The JCN suffix is a structured alphabetic or alphanumeric code added to the basic JCN to identify a subassembly or sub-subassembly repair action performed independently of the major component repair. The

suffix is used by Intermediate Maintenance Activities (IMA) only Figures 16-1 and 16-2 contain a complete structure breakdown of a suffix within a suffix. The following listing is a breakdown of the double suffix logic: First Position Second Position Position Identification 16-1 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Alpha Alpha Numeric Blank Alpha Alpha A repairable subassembly, which has repairable sub-subassemblies. A repairable sub-subassembly removed from a repairable subassembly. A repairable subassembly with no repairable sub-subassemblies. 16.1115 NALCOMIS provides automatic assignment of JCNs 16.112 Work Center Workload Reports Work Center Workload Report data is updated throughout the production day by using various on-line functions. The Workload Inquiry (Figure 16-3) provides effective control of maintenance by providing current status of all maintenance actions. These procedures provide the necessary management tools essential for real time management information

on a continuing basis. 16.113 NALCOMIS Maintenance Action Form (MAF) and Naval Tactical Command Support System (NTCSS) Optimized Organizational Maintenance Activity (OOMA) NALCOMIS Configuration Management Auto Log Set (CM ALS) Records Flow 16.1131 Off-Equipment Work When a not ready for issue (NRFI) component is received at the aeronautical material screening unit (AMSU), the following induction procedures will be followed: a. If AMSU personnel have the appropriate special maintenance qualification (SMQ), induct the item by assigning a work priority. NALCOMIS will print two MAFs: one for Production Control and the second to accompany the component to the work center. NTCSS Optimized OMA NALCOMIS CM ALS record will be moved to an induction status. b. AMSU personnel who do not have the SMQ to assign a work priority will induct the component without a priority assigned. NALCOMIS creates the mailbox message, PC Approval Required and moves the NTCSS Optimized OMA NALCOMIS CM ALS record to

Induction Status. Production Control approves the MAF by assigning a work priority and indicating approval. Two MAFs will be printed; one for Production Control and one to accompany the component to the appropriate work center. NOTE: The Production Control copy is for local use. c. AMSU routes the component, with a MAF, to the work center d. When directed by Production Control, the work center places the component in-work (IW) e. If the work center determines that repair parts are required the work center uses various on-line functions confirming the correct part data prior to ordering. Using the appropriate function, the work center will order the parts required. NALCOMIS provides Production Control with specific mailbox message identifying each MAF awaiting parts approval. For NTCSS Optimized OMA NALCOMIS, components or subcomponents that are removed and replaced will be documented in the configuration management (CM) task. Procedures are in the OMA-UG f. Production Control will

indicate approval by assigning a project code and issue priority code and NALCOMIS will automatically assign the proper sequenced document date and serial number (DDSN) for each approved part and produce required MAFs to support shop replaceable assembly (SRA) turn-ins and work center updates. For NTCSS Optimized OMA NALCOMIS, components or subcomponents that are removed and replaced will be documented in the CM task. Procedures are in the OMA-UG/Online Help g. If the DDSN local status code reflects nonavailability of the part requisitioned, the work center changes the MAF job status (JS) to WT (in transit to AWP locker) and routes the part with MAF to the awaiting parts (AWP) unit. The AWP unit performs receipt function that changes the MAF JS to WQ (Gear in AWP Work Center). For parts authorized to remain in shop, the same procedures apply 16-2 COMNAVAIRFORINST 4790.2C 15 Jan 2017 h. When all parts are received by the AWP unit, the MAF JS will be upgraded to WB (in transit from

AWP unit to work center) via online functions. i. When the maintenance action is completed, the worker updates the JS to JC NALCOMIS creates the mailbox message for "Collateral Duty Inspector (CDI) Approval Required" or "Quality Assurance (QA) Approval Required". j. Upon CDI or QA approval, NALCOMIS creates the "Supervisor Required" mailbox. k. When the MAF has been approved by the Work Center Supervisor, NALCOMIS creates the mailbox message, Production Control Review. l. When Production Control approves the MAF, NALCOMIS prints two copies of the completed MAF. The first copy is routed with the component and the other one is retained by the work center for maintenance report verification. For NTCSS Optimized OMA NALCOMIS, ensure CM ALS records accurately reflect SERNO, CAGE, P/N, status, and configuration of the component. NOTE: If the component is a due in from maintenance (DIFM) asset, NALCOMIS creates the mailbox message "Completed Repair

Actions" once Production Control review function is complete. m. AMSU or equivalent picks up the component from the work center and delivers the ready for issue (RFI)/beyond capability of maintenance (BCM) component to the Aviation Supply Department (ASD) with the completed MAF, Aeronautical Equipment Service Record (AESR), Module Service Record (MSR), Assembly Service Record (ASR), Equipment History Record (EHR), or Scheduled Removal Component (SRC) card and RFI or BCM tag for disposition. DIFM return moves NTCSS Optimized OMA NALCOMIS CM ALS records to RFI, BCM, or out folder (as applicable). n. Upon Logs and Records review, NALCOMIS prints two copies of the completed MAF; one for Production Controls historical files for a minimum of 6 months and the second copy for the QA review. NALCOMIS creates the mailbox message "Data Analyst Review". o. Figure 16-4 shows NALCOMIS MAF Off-Equipment document flow NOTES: 1. NALCOMIS generates configuration documents for updating

engine AESR/MSR and associated records. 2. Requisition and turn-in procedures for Aviation Life Support System (ALSS) and armament equipment and repair parts shall be per Type Commander (TYCOM) guidelines (where applicable) or as established in this instruction. All ALSS and armament turn-ins will be delivered directly to the ALSS and armament pool. The NTCSS Optimized OMA NALCOMIS CM ALS records will be delivered electronically to the ALSS and Armament Equipment Branch. ALSS and armament equipment maintenance will be documented in CM task. CM inventory will accurately reflect the physical status 16.1132 The following is a sequence of events when one work center requires assistance from another work center. The MAF flow is as follows, for the control of work in the assisting work center: a. The primary work center generates a MAF using the Work Center Assist/Support MAF Initiation function. b. Production Control approves the assist MAF using the appropriate on-line function NALCOMIS

will produce (two) MAFs; one for the assisting work center and one for Production Control. 16-3 COMNAVAIRFORINST 4790.2C 15 Jan 2017 c. When the assist MAF has been completed, a copy of the MAF will be provided to the primary work center. 16.1133 On-Equipment Work a. Items inducted from O-level (On-Equipment Work Initiated by I-level Documentation Flow (Figure 16-5)): (1) Production Control receives the equipment and a MAF from the originating activity for inspection or repair of support equipment (SE) and items for which the originating activity has Individual Material Readiness List (IMRL) reporting responsibility. Custody Code L items in user custody, which were checked out from the parent IMA, are to be processed as user reporting IMRL items for MAF flow during deployment. Look phase JCNs will be assigned for PM actions When Production Control receives SE that is in NTCSS Optimized OMA NALCOMIS all maintenance will be documented using CM task. CM Inventory will accurately

reflect physical status (2) Production Control inducts the MAF into NALCOMIS. NALCOMIS prints two MAFs; one for customer receipt and the second is routed to the work center. (3) When corrective action and the MAF have been completed, Production Control retains a copy of the MAF. An additional MAF will accompany the item back to the originating activity NOTE: Production Control shall maintained/updated Custody and maintenance history records received with O-level SE while the item is in a repair status. For NTCSS Optimized OMA NALCOMIS CM ALS records, SE will accurately reflect physical status using the CM Inventory update. CM Task has to be used to update NTCSS Optimized OMA NALCOMIS CM ALS records. Procedures are in the OMA-UG b. Maintenance actions originated by the I-Level Documentation Flow (Figure 16-5) I-level activities will initiate MAFs for scheduled and unscheduled maintenance of I-level IMRL/SE, such as test benches, mobile facilities, and tow tractors. MAFs for each

maintenance action is initiated with the following information: (1) Type Equipment Code (TEC). (2) BUNO/SERNO. (3) Discrepancy (required). (4) Equipment status (required for level 1). (5) When Discovered Code (required). (6) JS (optional). (7) JS Date (optional). (8) JS Time (required if date entered). (9) Work Center (required). (10) Type Maintenance (required). (11) Maintenance level 1. 16-4 COMNAVAIRFORINST 4790.2C 15 Jan 2017 (12) WUC (required and must be reside on the database). (13) Work Priority (allowed with proper SMQ). (14) Meter (required if maintenance level equals 1). (15) System Reason (required). NOTE: Production Control will perform the above functions for WD Code O documents. Any IMA personnel may initiate corrosion prevention MAF. c. If Work priority (PRI) not assigned, NALCOMIS creates mailbox message "Production Control approval required". Production Control approves the MAF using the appropriate function and routes the MAF to the work center. d.

When the maintenance action is completed, the worker updates the JS to JC NALCOMIS creates the mailbox message for "CDI Approval Required" or "QA Approval Required": (1) Upon CDI or QA approval, NALCOMIS creates the "Supervisor Required" mailbox. (2) When the MAF has been approved by the work center supervisor, NALCOMIS creates the mailbox message "Production Control Review". e. When Production Control reviews the MAF, NALCOMIS prints two copies of the completed MAF, one to be routed with the component. The second copy is retained by the work center for maintenance report verification. f. Upon Logs and Records Review NALCOMIS prints two copies of the completed MAF; one for Production Controls historical files for a minimum of 6 months and one for "QA Review". NALCOMIS creates mailbox message "Data Analyst Review". g. MAF flow within the Weapons Department for on-equipment maintenance of AWSE end items will be the same as the

procedures discussed above, even though several of the maintenance functions, which are organized as separate entities in IMA, may be combined organizationally into one in the Weapons Department. For example, Maintenance Control, the work center, and Material Control could exist as a single point in the Weapons Department, and the standard MAF flow procedure would still be used just as though these three entities had been geographically, rather than organizationally, collocated. 16.1134 MAF Filing Requirements a. A completed MAF shall be retained by Production Control as a historical file for a minimum of 6 months from completion date. This file will be arranged by JCN date and serial number sequence, and grouped by month of completion. Individual units have the option of establishing local files by work center as long as the above filing order is maintained. A temporary file may also contain those MAFs with a close out Action Taken Code of L or N. b. Completed engine MAFs shall be

maintained in the engine historical file by engine type and serial number, in JCN sequence, for 6 months from the completion date on the engine induction MAF. The file shall contain the completed MAFs for repairs/inspections of the engine, engine test cell performance sheets, and all the completed local forms generated for pre-induction screening. NOTE: NALCOMIS FRCs with history retrieval implemented are not required to maintain paper historical MAF files. This eliminates countless man hours sorting and filing paper MAFs in 16-5 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SESS record folders. Documentation of required entries shall be made and checklists will be maintained per paragraph 10.17 16.114 Controlling Awaiting Maintenance Within space allocations, items AWM should be stored in a central location. If bins are available, the exact location of the AWM item may be marked on MAF to facilitate location by AMSU. Keeping AWM and AWP items out of the work centers and in a central

location helps prevent damage to the items and may reduce indiscriminate, unauthorized, cannibalization. When centralized location of AWM items is not possible, due to space limitations, AWM items may be stored in the work centers. 16.115 Maintenance Reports Maintenance reports are valuable tools available to the maintenance manager. 16.116 Interface Requirements It must be remembered at all times that the IMAs primary mission is to support the operating activities. To achieve this, there must be a close liaison with supported activities and cognizant D-level activities. 16.1161 Relationships must be maintained with the supported organizational maintenance activities in the following areas: a. Deployment schedules, for projecting temporary additional duty (TAD) This should be part of the Monthly Maintenance Plan (MMP). b. Power plant inductions, for scheduling purposes c. Test, Measurement, and Diagnostic Equipment (TMDE) and SE inductions, for scheduling purposes. d. SE licensing

requirements, for O-level personnel e. Navy Oil Analysis Program (NOAP) requirements, aboard ship (paragraph 103) f. No defects, that is, action taken (AT) Code A on the MAF for maintenance actions from the Olevel activities, to improve troubleshooting techniques and assist in decreasing wasted man-hours at the IMA. 16.1162 Inter IMA Support Instances will occur where a repairable component, which is beyond the capability of the local maintenance activity, is shipped to an off-station IMA for repair and return. a. Processing Defective Components for Shipment to an Off-station I-level activity for Repair and Return: (1) AMSU receives the defective component with a completed MAF with AT Code D, condition tag, and associated records or NTCSS Optimized OMA NALCOMIS CM ALS records from the work center and forwards them to Document Control Unit (DCU). (2) DCU processes the component via the DIFM return function. (3) Supply ships the component with MAF, associated records, and DOD Single Line

Item Release Receipt Document (DD 1348-1) per local supply procedures. NTCSS Optimized OMA NALCOMIS CM ALS records are transferred electronically to the unit identification code (UIC) that the component is shipped to. 16-6 COMNAVAIRFORINST 4790.2C 15 Jan 2017 b. Processing Defective Components from Off-station I-level activity for Repair and Return: (1) Supply receives the defective component with the D action MAF, associated records or NTCSS Optimized OMA NALCOMIS CM ALS records, and DOD Single Line Item Release Receipt Document (DD 1348-1) per local supply procedures. (2) Supply delivers the defective component, MAF, and associated records or NTCSS Optimized OMA NALCOMIS CM ALS records to AMSU. (3) AMSU inducts the MAF, fills in the Repair and Return, and the Owed Org field. (4) AMSU receives the component with a completed MAF, and associated records or NTCSS Optimized OMA NALCOMIS CM ALS records from the work center or production control. (5) The Component Control Section (CCS)

receives the component from AMSU and processes it to the originating I-level activity via the DIFM return function. (6) Supply ships the component with MAF, associated records, and DOD Single Line Item Release Receipt Document (DD 1348-1) per local supply procedures. NTCSS Optimized OMA NALCOMIS CM ALS records are transferred electronically to the UIC that the component is shipped to. c. Processing Component Returned from an Off-station I-level Activity as a Result of a Previous Local BCM Action: (1) Supply receives the component, MAF, associated records, or NTCSS Optimized OMA NALCOMIS CM ALS records and DOD Single Line Item Release Receipt Document (DD 1348-1) per local supply procedures. (2) Supply delivers the RFI component and records or NTCSS Optimized OMA NALCOMIS CM ALS records to the customer. NRFI components received are processed per local procedures NOTE: Components shipped as RFI but without an RFI tag will be inducted into the IMA for check and test. The CCS will

initiate the work request using a supply JCN via on-line functions 16.12 Production Division Officers Responsibilities In addition to the functions of naval officers in U.S Navy Regulations, each division officer shall comply with the following paragraphs. 16.121 Division officers shall become knowledgeable of and familiar with maintenance reports concerning their division. 16.122 Division officers shall develop an understanding of NALCOMIS and NTCSS Optimized OMA NALCOMIS concepts and applications to management and MIS requirements. 16.13 Work Center Supervisors 16.131 Introduction If successful accomplishment of assigned tasks of the IMA could be attributed to any one group of personnel, it would be the Work Center Supervisors. Diligent supervision at the work center level includes rigidly adhering to the procedures and policies established by this instruction. To ensure the accomplishment of all assigned work, maximum efficiency must be obtained and maintained in the use of 16-7

COMNAVAIRFORINST 4790.2C 15 Jan 2017 manpower, material, and facilities. This is most easily done within the work center by using the systems and programs in this chapter. 16.132 Communication The primary job of the work center is to be responsive to the hour-by-hour maintenance situation. This requires constant communications between the work center and Production Control. To assist Production Control in keeping abreast of the maintenance situation, the Work Center Supervisor must keep Production Control constantly notified of the following: 16.1321 Bench/test equipment status 16.1322 Availability of skills (personnel) 16.1323 Changes in status of assigned maintenance, for example, in work to AWM and in work to AWP. 16.1324 Anything which may affect the ability of the work center to maintain the systems assigned 16.133 Machine Reports This paragraph outlines the daily and monthly NALCOMIS and MDRs which the Work Center Supervisor uses on a regular basis. They are: 16.1331 NALCOMIS

Reports a. The Work Center Workload Report is the NALCOMIS Visual Information Display System (VIDS) board. The report is a valuable validation tool The report lists all outstanding discrepancies not signed off by Production Control for each work center as of the selected end date and time of the report. b. The Equipment Discrepancy Report lists the serial number and the type equipment code of all pieces of SE, engines, or both that currently have outstanding MAFs. c. The Due In From Maintenance Report is used to validate components in the repair cycle, monitor job status, explore cannibalization/transpose possibilities, monitor supply status for AWP requirements, monitor repair and return assets (both incoming and outgoing). d. The Daily Production Report - Part 1 lists all completed maintenance actions signed off by Production Control, within the user-entered begin and end date range, within a work center. These maintenance actions are totaled by priority, transaction codes, and

action taken codes. This is simply a record of what was completed during the report time span. The Daily Production Report - Part 2 provides a count of all maintenance actions accomplished from the begin date/time to the end date/time as selected by the user. NOTE: A complete listing of reports available, including their uses and detailed instructions, is in Chapter 14. 16.134 Data Accuracy Throughout the MDS, accurate documentation must be stressed. Each uncorrected erroneous document results in a loss of effectiveness of the data and of the system. The importance of complete and accurate data is further emphasized when Navy-wide use of these data are considered. Work Center Supervisors, with the assistance of the analyst, shall strive at all times for absolute accuracy. 16-8 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.135 Work Center Workload Report The Work Center Workload Report is updated throughout the production day by using various on-line functions. The Workload Inquiry

provides effective control of maintenance by providing current status of all maintenance actions. These procedures provide the necessary management tools essential for real time management information on a continuing basis. The Production Control supervisor shall establish a schedule and ensure all work centers verify their work center workload reports against the actual component and status inducted to their work center on a daily basis. 16.136 NALCOMIS Automated Procedures 16.1361 The work center receives the MAF with the NRFI component MAF data is maintained and updated on a continuing basis through on-line functions. When the maintenance action and MAF have been completed and the component is RFI or determined to be in a BCM condition, attach the hard copy of a Serviceable Tag - Material (DD 1574) or Material Unserviceable (Reparable) (DD 1577-2) (Figure 16-6) to the component inside the shipping container. This tag remains attached to the component until the component is used or

destroyed. A MAF and a flimsy copy of the Material Condition Tag, serviceable label or unserviceable label are attached to the outside of the shipping container. 16.1362 Paragraph 162 lists procedures for documenting maintenance of SE Figure 16-5 shows the MAF flow for SE end items through the maintenance cycle. NOTE: MAF flow within the Weapons Department for on equipment maintenance of armament weapons support equipment (AWSE) end items may vary from the illustration because several maintenance functions, which are organized as separate entities in the IMA, may be combined organizationally into one in the Weapons Department. For example, Production Control work center and Material Control could exist as a single point in the organization. 16.1363 The supervisors name in the supervisor field signifies completion of the maintenance action, verification that tool control inventories were conducted at the proper intervals, the component was adequately preserved and secured for routing

to the AMSU, documentation is correct, and QA measures were adhered to. 16.1364 Complete details on MAF documentation are in paragraph 162 16.137 Material Requisitioning 16.1371 The Work Center Supervisor must ensure that work center personnel know the procedures for ordering parts to repair WRAs and SRAs. 16.1372 If the work center determines that repair parts are required, the work center uses various on-line functions confirming the correct part data prior to ordering. Using the appropriate function, the work center will order the parts required. NALCOMIS provides Production Control with specific mailbox message identifying each MAF awaiting parts approval. 16.1373 Production Control will indicate approval by assigning a project code and issue priority code NALCOMIS will automatically assign the proper sequenced DDSN for each approved part and produce required MAFs to support SRA turn-ins and work center updates. 16.1374 If the item is not available within 24 hours, or the DDSN

local status code reflects nonavailability of the part requisitioned, the work center changes the MAF JS to WT (in transit to AWP locker) and routes the part with MAF to the AWP unit. The AWP unit performs receipt function that changes the MAF JS to WQ (Gear in AWP Work Center). For parts authorized to remain in shop, the same procedures apply. Production Control is notified of the status change via NALCOMIS 16-9 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.1375 If a repairable SRA is requisitioned, the DDSN assigned by NALCOMIS becomes the turn-in document number on the MAF initiated by the work center for that SRA. NALCOMIS issues a suffix JCN from the original JCN and the work center packages and preserves the SRA for induction into the repair activity having cognizance. 16.1376 When all parts are received by the AWP unit, the MAF JS will be upgraded to WB (in transit from AWP unit to work center) via online functions. The component and parts are delivered to the work center.

16.1377 A component may go through the AWM, in work, and AWP process many times before being RFI or it is determined that the item must be shipped to another activity for repair. If so, ensure the above steps are taken each time the status of the component changes. 16.1378 When the decision is made to process the WRA for BCM-4 action, the following steps are taken: a. Notify Production Control of the status change from AWP to in work b. Ensure all SRAs are installed and secured, and all documentation is provided for any missing SRAs. c. Preserve for off-station processing d. Complete MAF documentation and notify Production Control of the status change from in work to BCM-4 via local procedures. NOTE: Paragraph 16.2 lists detailed documentation procedures 16.138 High Usage Piece Parts Available in the Pre-Expended Bin (PEB) The Work Center Supervisor must be familiar with PEB operations. Although stocking of PEBs is the responsibility of the ASD, the inputs for stocking will originate

at the work center. The ASD will stock only those items, which, among other things, show a high usage. To ensure the required parts are stocked in the PEB, the Work Center Supervisor shall: 16.1381 Ensure all piece parts usage is properly accounted for, and if the piece part contributed to the failure, documented in the FAILED/REQUIRED MATERIALS field of the MAF. 16.1382 Ensure parts which are normally stocked in the PEB, but are at a low level, are reordered promptly by the ASD per local procedures. 16.1383 Periodically review the work centers PEB requirements and compare them against actual PEB stocking levels. 16.139 Tool Control in the Work Center responsibilities: The following lists Work Center Supervisors 16.1391 Upon task assignment, note the tool container number in NALCOMIS using the appropriate function. The technician shall conduct a sight inventory prior to commencement of each task and all shortages shall be noted on the toolbox inventory card. Every measure must be

taken to ensure missing tools do not become a cause of FOD. Inventories shall also be conducted at shift change, when a work stoppage occurs, after maintenance has been completed, and before conducting an operational systems check on the equipment. 16-10 COMNAVAIRFORINST 4790.2C 15 Jan 2017 NOTE: The above procedures are mandatory only in Power Plants, ALSS, AWSE, and SE Division (900) work centers. For all other work centers, these procedures may be omitted except for the shift change inventory. 16.1392 After maintenance has been completed, and before an operational systems check on the equipment, the inspection process shall once more be performed. 16.1393 When all tools are accounted for, and all maintenance actions have been completed, the work center supervisor approves the MAF signifying that maintenance has been completed and that all tools have been accounted for. NOTE: The above procedure applies only to the power plants, ALSS, AWSE, and SE Division (900) work centers.

For all other work centers, the supervisors name signifies that the unit or component repaired was inspected and found to be free of any foreign objects, which might later be the source of equipment/engine damage. 16.1394 If any tool is missing at any one of the above stages, an immediate search shall be conducted prior to reporting the work completed or signing off the MAF. If the tool cannot be located, immediately notify Production Control. Production Control will notify the Maintenance Officer (MO) or acting MO 16.1395 If the tool cannot be located after the MOs directed search, the person doing the investigation shall enter their name and the statement in the Corrective Action field of the MAF that a lost tool investigation was conducted and the tool could not be found. Subsequently, the normal MAF completion process shall be followed. 16.1396 CDIs shall assist the Work Center Supervisor in complying with the Tool Control Program 16.14 Maintenance Information Systems (MIS) 16.141

NALCOMIS Procedures The Workload Inquiry and reports provide Production Control work centers with a display of SE end items and components being repaired. This allows Production Control to manage the workload in a selected work center. The issue, receipt,inventory, and location (IRIL) board (Figure 16-7) or the support equipment standardization system (SESS) shall be used by IMAs as a tool for inventory management of assigned SE. The IRIL board provides a display of SE assigned to the SE Division for management IRIL boards shall be arranged by TEC. 16.142 IRIL Procedures The acceptable methods of displaying IRIL information are VIDS 1 and SESS: 16.1421 VIDS 1 is composed of IRIL boards The IRIL board may be used by I-level activities as a tool for inventory management of assigned SE (Figure 16-7). This board provides a graphic display of SE assigned to the SE division for management. IRIL boards shall be arranged by TEC 16.1422 Inventory The SE inventory shall be displayed on the IRIL

board using locally produced indicator strips annotated with TEC, model, and serial number. Locator tabs, either color coded or indexed, shall be used to indicate physical location. Processed SE Transaction Reports (OPNAV 4790/64) may be used on the IRIL board to display location/custody information. 16.1423 Locator Tab An example of this locator tab is shown in Figure 16-8 This locally produced card is color coded or indexed to indicate the activity that has subcustody of the equipment and its physical location. The tab will be placed on the IRIL board to the right of the inventory card for the equipment being issued. 16-11 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.143 SESS and NALCOMIS SESS is a microcomputer-based asset control system. SESS does not provide a method to control production and show current job status (IN WORK, AWP, AWM). SESS provides automated methods for: 16.1431 Inventory tracking and reporting 16.1432 Preventive Maintenance (PM) scheduling 16.1433 Technical

Directive (TD) accounting 16.1434 Subcustody management 16.1435 Accurate and timely reports NOTES: 1. SESS and NALCOMIS must be used concurrently for proper management 2. For further details on SESS refer to the SESS Users Guide 16.144 Historical Files Production Control shall file a completed copy of a noninspection MAF for a minimum of 6 months from the completed date. MAFs, in support of PM inspections, will be maintained for 6 months or one complete inspection cycle whichever is greater. This file will be arranged in sequence of equipment nomenclature, SERNO, and JCN, that is JCN within SERNO within nomenclature. These files and all outstanding discrepancy MAFs shall accompany SE that is transferred or temporarily loaned to another activity. NOTE: NALCOMIS IMAs with History Retrieval implemented will store completed MAF data in the NALCOMIS database for 6 months from completion date, and documents in support of PM inspections will be stored for 6 months or one complete inspection

cycle, whichever is greater. Anytime a NALCOMIS IMA with History Retrieval transfers or temporarily loans SE to another activity, the transferring activity shall produce a NALCOMIS IMA ad hoc SE Transfer Report (Figure 16-9) and send it to the receiving activity. 16.15 VIDS Operation 16.151 VIDS Board Effective control of maintenance is dependent on the availability of easily identifiable status of all maintenance resources. The most efficient method of quick reference to most of those resources for activities not supported by NALCOMIS IMA is use of the VIDS board. The VIDS board is a management tool that provides the visual display of essential information, for example, component repair status (In Work, AWM, and AWP), on a continuing basis on all the components within the production area. The ability to review the overall situation and determine what resources are available lets the Production Control Officer or supervisor carry out duties more effectively and efficiently. Activities

experiencing NALCOMIS IMA downtime in excess of 5 working days may also find using the VIDS board a beneficial contingency option. 16.152 VIDS Board Layout (Figure 16-10) Actual display techniques may vary to meet local requirements; however, the following items are considered essential to the Production Control effort and must be displayed. 16-12 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.1521 Column 1 - WC & EQUIP List the work centers and the equipment repaired by each work center by P/N or WUC. 16.1522 Column 2 - SE Use an orange signal tab to indicate test benches or equipment inoperable, or a yellow tab to indicate partial capability. 16.1523 Column 3 - QTY Enter the quantity of a particular P/N or WUC capable of being worked on at any one time. 16.1524 Column 4 – Local Repair Cycle Asset (LRCA) LIMITS HI/LOW Enter the maximum allowable LRCAs due to fixed allowances under the "HI" column and the low LRCA level under the "LOW" column. 16.1525 Column 5 -

PRI Display the workload priority by using colored tabs Tabs may also be placed over each individual VIDS/MAF. The use of different colored signal tabs are as follows: a. Green - LRCA is pool critical b. Blue - LRCA is pool zero c. Red – Expeditious Repair (EXREP) 16.1526 Column 6 - AWM Display those items that are AWM 16.1527 Column 7 - IN WORK Display those items that are being repaired 16.1528 Column 8 - AWP Display those items that are AWP 16.1529 Column 9 - COMPLETED This column is optional but may be used to temporarily store VIDS/MAF Copy 3 from the time a work center reports an item RFI or BCM until VIDS/MAF Copy 1 is returned to Production Control. VIDS/MAF Copy 3 then may be removed and stored in another location, after verifying it with VIDS/MAF Copy 1, until VIDS/MAF Copy 1 returns from data entry. 16.153 VIDS Board Verification The Production Control Supervisor shall establish a schedule to ensure all work center VIDS boards are verified with the Production Control VIDS

board and discrepancies resolved at least daily. AWP component repair status shall be validated at least weekly. 16.154 VIDS/MAF Flow; Off-Equipment Work 16.1541 The following describes the sequence of events that occur from the time a component leaves the AMSU until it is made RFI or declared BCM (Figure 16-11): a. When VIDS/MAF copy 3 is delivered to Production Control by AMSU, the following blocks are already filled in by the originating activity and screened by the AMSU: A08, A11, A14, A22, A48, A52, A58, A59, A60 (if applicable), B08, E08, E13, E23, E38, E42, E47, and E52 (if applicable), DISCREPANCY, PILOT/INITIATOR, and TURN-IN Document. b. Production Control fills in block A19 and puts VIDS/MAF copy 3 on the VIDS board in the AWM column under the work center by P/N or WUC. c. When notified by Production Control, AMSU routes the component with VIDS/MAF copies 1, 4, and 5 to the work center. 16-13 COMNAVAIRFORINST 4790.2C 15 Jan 2017 d. When told by Production Control, the

work center puts the component in work Production Control annotates block B19 with the Julian date and moves VIDS/MAF copy 3 to the in work column of the board. e. If the work center determines repair parts are required, they notify Production Control Production Control assigns the project code and supply priority and annotates VIDS/MAF copy 3 with an S in block B53 indicating the component is entering a supply status and the Julian date in block B54 indicating the date that supply transmitted the requisition document. After entering the appropriate information in the H through Z blocks, VIDS/MAF copy 3 is moved to the AWP column of the VIDS board. f. After notification that repair parts are not available locally or when status is not received after 24 hours, the work center routes the component with VIDS/MAF copies 1 and 4 to the AWP unit. VIDS/MAF copy 5 remains on the work center VIDS board in the AWP column. g. When notified by the AWP unit that all parts have been received,

Production Control enters an M in block B65 indicating the component is back in a maintenance status, the Julian date in block B66, and moves VIDS/MAF copy 3 to the AWM or In Work column of the VIDS board, whichever applies at the time. NOTE: This procedure, steps (e) through (g), may be repeated many times before the component leaves the IMA. h. When the work center completes all maintenance actions, they notify Production Control of the status; RFI or BCM. Production Control enters the completed Julian date in block B30 and moves VIDS/MAF copy 3 to a temporary file, such as, the completed column of the VIDS board. i. AMSU, or equivalent, picks up the component from the work center, delivers the completed VIDS/MAF copy 1 to Production Control, returns the RFI or BCM component with appropriate logs and records, for example, AESR or SRC Card, to the Supply Support Center, along with VIDS/MAF copy 4. j. Production Control verifies VIDS/MAF copy 3 with the completed copy 1 and records

any information deemed necessary on the copy 3, for example, action taken and malfunction code. k. Production Control forwards VIDS/MAF copy 1 to the analyst for data entry or NALCOMIS backfit and puts Copy 3 in a temporary file other than the completed column of the VIDS board. l. Upon return of VIDS/MAF copy 1 from the analyst, Production Control files it in the historical files and destroys VIDS/MAF copy 3. If a Ship’s Maintenance Action Form (OPNAV 4790/2K) is attached to the VIDS/MAF, annotate the completion date of the VIDS/MAF in the OPNAV 4790/2K discrepancy block, remove, and file in the historical file. Figure 16-11 depicts off-equipment VIDS/MAF flow throughout the maintenance cycle. NOTE: Requisition and turn-in procedures for ALSS assemblies and repair parts shall be per NALCOMIS guidelines (where applicable) or as established in this instruction. All ALSS turn-ins will be delivered directly to the ALSS pool. 16.1542 The following is a sequence of events when one work

center requires assistance from another work center. The VIDS/MAF flow for the control of work in the assisting work center is as follows: a. The primary work center generates a VIDS/MAF using WD Code V and processes it through Production Control along with the part requiring repair. 16-14 COMNAVAIRFORINST 4790.2C 15 Jan 2017 b. Production Control assigns the work priority and attaches the assist VIDS/MAF copy 2 to the basic VIDS/MAF copy 3 for which assistance was requested. Assist VIDS/MAF copy 3 is placed on the Production Control VIDS board, under the assisting work center. c. Assist VIDS/MAF copies 1, 4, and 5 are routed with the part and all required material to the assisting work center for processing. When the process has been completed by the assisting work center, assist VIDS/MAF copies 1 and 4 are forwarded with the part to Production Control, and copy 5 is retained for MDS validation by the work center. d. Production Control clears applicable VIDS boards of assist

VIDS/MAF copies 2 and 3 and forwards copy 1 to QA. VIDS/MAF copy 3 is held in the suspense file until copy 1 is returned from data entry. VIDS/MAF copy 2 is destroyed and copy 4 is sent with the part back to the work center that requested the assistance. 16.2 I-Level Maintenance Source Document Procedures Note: The C-555-0061 IMA Documentation course should be completed by new (first tour) personnel assigned to I-level activities. 16.21 Maintenance Action Documentation Procedures The purpose of this section is to give detailed procedures for documenting maintenance actions using NALCOMIS procedures. Examples of completed MDR forms are in this chapter 16.211 Types of Maintenance Action Form (MAF) Maintenance Actions 16.2111 This paragraph outlines the types of maintenance actions documented on MAFs These include troubleshooting, removal and replacement, repair, and the performance of scheduled inspections. 16.2112 MAFs will be used to document the following types of maintenance

actions: NOTE: Type MAF Code must be used in NALCOMIS, but does not appear on the hard copy MAF. a. On-equipment work not involving the removal of defective or suspected defective repairables b. Look phase of acceptance, transfer, special, conditional, major aircraft and combined airframe and engine special inspections, and corrosion, preservation and depreservation. c. Fix in place actions discovered during inspection d. Removal of components for check, test, or service actions e. Removal and replacement actions for cannibalization f. Accumulated man-hours as a result of work stoppage for parts or maintenance. g. Accumulated man-hours during or at the end of a reporting period for a job not completed, where required by the cognizant ACC or TYCOM. h. Maintenance actions and man-hours by assisting work center in support of a primary work center i. Support of a repairable item processing through the IMA. j. Incorporation of TDs and associated maintenance actions. 16-15

COMNAVAIRFORINST 4790.2C 15 Jan 2017 k. Removal and replacement of repairable components in end items l. Repair of removed repairable components. m. Repair of subcomponents removed from repairable components n. Record of ordering and issue of repairable components, subassemblies, and parts o. Disposition of components and subassemblies declared BCM p. Major inspections performed on removed engines, when initiated by an O-level activity q. Documentation of first-degree repair maintenance actions r. Troubleshooting man-hours. s. Documenting preservation and depreservation 16.212 Intermediate Document Flow 16.2121 Examples of MAF documentation are included in this chapter 16.2122 The Material Control AMSU receives the defective component with a MAF AMSU personnel using AMSU Receipt function enters the appropriate data into NALCOMIS. Upon approval, 2 copies of MAFs are generated. One is attached to the defective component for delivery to the applicable work center, the other is for

Production Control. 16.2123 The Work Center Supervisor receives the component, screens the MAF, and assigns a worker to the maintenance action. The worker performs technical screening and commences the repair action 16.2124 If parts are required, the worker will order necessary parts using the appropriate function 16.2125 Once maintenance is completed, the worker updates the MAF indicating the appropriate action, and assigns a job status of JC. At this time a mailbox message is created for the CDI and the worker attaches a material condition tag to the component. 16.2126 The CDI reviews the MAF in the appropriate NALCOMIS function indicating approval At this time NALCOMIS will electronically assign CDIs name to the Inspected By Field of the MAF. A mailbox message will be created for the Work Center Supervisor. 16.2127 The Work Center Supervisor reviews the MAF in the appropriate NALCOMIS function and screens the MAF for accuracy and completeness. Upon approval, the Work Center

Supervisors name is electronically assigned to the MAF and a mailbox message will be created for Production Control. At this time the AMSU is notified that the component is ready for pickup. 16.2128 Production Control reviews the MAF Upon approval, the Production Controllers name is electronically assigned to the MAF. At this time NALCOMIS generates two MAFs One for the work center which is used to verify the maintenance report and the second MAF will accompany the component to AMSU for disposition. A mailbox message is created to logs and records for review Logs and Records personnel will ensure NTCSS Optimized OMA NALCOMIS CM ALS records are updated for the component or equipment that is changed. 16.2129 AMSU notifies the CCS that the component is ready for disposition and delivers the component to CCS. 16-16 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.21210 When a repairable NRFI subassembly is removed from the component, the work center attaches the suffix MAF to the NRFI

component and notifies AMSU that the subassembly is ready for turn-in. NOTE: Additional parts required for induction, repeat procedures outlined in paragraphs 16.2112a through 16.2112h above 16.21211 The MDBA/A reviews the appropriate mailbox message and approves or rejects completed MAFs. Approved MAFs are then submitted to the SSCA 16.213 Data Field Description 16.2131 This section describes the NALCOMIS functions recommended for initiating, updating, and clearing the NALCOMIS MAF. This section also contains an explanation of the functions required to add/delete the NALCOMIS MAF. The codes used to describe the data throughout the sections of the MAF are in Appendix E and the applicable WUC structure assigned to the OOMA baseline or the WUC manual for NALCOMIS users. Specific data fields to be used and data fields requirements are controlled by the Maintenance Data validation specifications (VALSPEC) in Appendix F. 16.2132 Specific data fields application and requirement are as

follows: ENTRIES REQUIRED SIGNATURE. This section is provided to ensure historical records and NTCSS Optimized OMA NALCOMIS CM ALS records are updated in a timely and orderly manner. Required actions will be accomplished prior to forwarding the MAF to the data analyst for approval. Logs and Records personnel will screen all MAFs using the appropriate function Upon indicating approval, NALCOMIS will electronically post their name to the MAF. LOCAL USE. This field may be used as desired REFERENCE. May be used to enter the supply reference to aid the work center in requisitioning the failed or required material. ACCUMULATED WORK HOURS NAME or SHIFT. Enter the name or shift of personnel performing the work Workers hours update will be used by the CDI or supervisor who will place their initials in the appropriate data field. Prior to JC or job status changes, for example, work stoppage, a sight inventory of the tool container(s) shall be conducted by the Work Center Supervisor or CDI. EMT.

NALCOMIS provides for the system generated EMT through its internal clock However, this field is not displayed in the Accumulated Work Hour Field on the NALCOMIS MAF. ACCUMULATED AWM HOURS. This time is automatically calculated within NALCOMIS FAILED/REQUIRED MATERIAL. This section will be used to document a failed part without an AWP situation, a failed part and an AWP situation occurring simultaneously, an AWP situation without a failed part, and a supply request only, with no failed part or AWP situation. NOTE: NALCOMIS will allow for and track up to 100 separate entries, and allow for the indexing of 19 separate lines of required data. INDEX. NALCOMIS will automatically provide for the proper indexing of ordered parts These letters represent a specific record type that will be generated via aviation 3M processing. This allows for the 19 most significant failed parts to be reported against a specific maintenance action. For example, assignment of index H indicates the first failed

part record, Z indicates the last and 19th failed parts record against the maintenance action. The purpose of indexing is to flag 16-17 COMNAVAIRFORINST 4790.2C 15 Jan 2017 engineering data items only, not supply usage data. Therefore, only significant failed parts will be annotated with H - Z in this field, that is those items which are known or suspected to have contributed to the discrepancy reported in the Discrepancy Field of the MAF. F/P. Enter an (x) to denote a failed part if the failed material or parts replaced during the repair are piece parts that have failed in a major component. Common hardware, nuts, screws, safety wire, seals, gaskets, washers, and fittings that are routinely replaced during a maintenance action will be documented only if their failure is known or suspected to have contributed to the discrepancy. NOTE: PEB items not in stock and required for repair of a discrepancy will be ordered against the MAF requiring parts. AWP. Immediately upon receipt of

notification that the repair part(s) is/are not available on the ship/station, the Work Center Supervisor will ensure an (x) is entered if the failed/required material is causing an awaiting parts status of the repairable item identified in the WUC Field. Only those items that caused the AWP status will be marked (x). In all cases, even if notification of nonavailability of repair parts is not received, the AWP component is to be delivered to the AWP holding area within 24 hours from the time the need for a repair part was discovered by the work center. (This field is used at maintenance levels 2 and 3) A/T. Enter the one-character alpha or numeric code, which describes the action taken against the removed module, subassemblies, or significant failed parts required. AT codes are listed in Appendix E. MAL. Enter the code that best describes the malfunction occurring within the removed subassembly. MAL codes are listed in Appendix E FSCM. Enter the CAGE code of failed part or required

material PART NUMBER. Enter the manufacturers part number of the failed or required material REF SYMBOL. Enter the alphanumeric code which identifies a piece part as distinct from other items of the same part number in a single subassembly or circuit, such as four of the same diodes within a circuit, each has the same part number but a different reference symbol. These are found in the illustrated parts breakdown manual for the weapon system. QTY. Enter the quantity of failed or required material PROJ. Enter project code as applicable PRI. Enter the MILSTRIP priority assigned to the material requisition DATE ORD. The Julian date the request was placed on order (NALCOMIS generated) REQ NO. The MILSTRIP requisition number of the material required to complete the maintenance action (NALCOMIS generated). DATE REC. The Julian date that requisitioned material is received (NALCOMIS generated) WORK UNIT CODE. Enter the WUC that identifies the system, subsystem, or component on which work is

being performed on. All repairable items must have a WUC assigned, which can be found by querying the applicable NACOMIS OOMA or the DECKPLATE WUC Baseline Report. If a WUC cannot be found for a repairable item, submit a Baseline Trouble Report (BTR) via JDRS to the NAVAIR TEC or WUC. For consumables not identified by specific WUC, use NHA WUC NOTE: General Work Unit Codes 030 (inspection) and 049 (preservation/depreservation) are used on the MAF as the WUC for conditional and acceptance/transfer inspections and for preservation/depreservation. Appendix E contains a complete listing of these codes 16-18 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ACT ORG. The organization code of the organization accomplishing the work (NALCOMIS generated). TRANS. Enter the two-character numeric transaction code used to identify the type of data being reported. Appendix E contains a complete list of these codes with definitions M/L. Enter the level of maintenance (1 through 3) which is performed (not

necessarily the level assigned to the activity). A/T. Enter the one-character alpha or numeric code that describes the action that has been taken This code describes what action has been performed on the item identified by the WUC. AT code A (discrepancy checked, no repair required) is used only in those cases where an inspection or operational check has been performed and the reported trouble cannot be duplicated or does not exist. In such cases use the MAL code 799 (no defect) Adjustments made to peak a system, which is within tolerances, may use this code with the appropriate malfunction code, for example, A-127, A-281, A-282. A consumable item replaced on a MAF should reflect the system or NHA code only in the WUC field and AT Code B or C. AT Code R should be used in the H-Z Failed/Required Material fields for parts replaced. AT Codes are in Appendix E NOTE: The TD status code is a single-character alpha code used to indicate the status of compliance with a TD. This code applies

to the action taken field of the MAF when reporting TD status These codes are in Appendix E. MAL CODE. Enter the three-character alphanumeric code used to describe the malfunction, which caused the maintenance action on the item described by the WUC. These codes are divided into three logical groups to assist personnel in finding the most applicable code as follows (MAL codes are contained in Appendix E): Conditional (no fault) Group. These codes are used when a nondefective item is removed, or when the defect/malfunction is not the fault of the item in question. Reason for Removal Group. These codes are used to generally describe trouble symptoms or apparent defects prompting removal of malfunctioning items for repair. Reason for Failure Group. These codes are used to generally describe underlying defects or basic failure reasons determined during repair of items exhibiting trouble symptoms. NOTE: Maintenance Control/Production Control shall enter the appropriate malfunction code

when initiating a cannibalization MAF. Malfunction codes are in Appendix E I/P. Enter the number of times that an action, indicated by an AT code, is applied to the item identified by the WUC recorded on a MAF, for example, since the fuel nozzle of a jet engine has a WUC, replacement of five fuel nozzles would be documented as five items processed. In contrast, replacement of several transistors in an electronic assembly would be documented as one item processed, with the WUC identifying the electronic assembly being repaired and the AT code indicating repair. MAFs submitted for close outs by work centers at the end of, or during a reporting period will indicate 0 items processed. The IP field is limited to two characters If the count exceeds 99, an additional form must be prepared and submitted. HOURS. Entries in the Hours field represent all man-hours expended by assigned personnel to complete the work described on the source document as defined in Appendix E. Hours and tenths

worked, multiplied by the number of men working, equals total man-hours. Entry in the Man Hours field does not include labor hours for any work center other than the one submitting the document, for example, if two work centers jointly correct a discrepancy (same JCN) on the same aircraft or equipment, workers from each work center submit a source document with that particular work centers labor hours in the Hours field. To convert minutes to hours and tenths, use the following example: 16-19 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MINUTES TENTHS MINUTES TENTHS 1-2 0.0 33-38 0.6 3-8 0.1 39-44 0.7 9-14 0.2 45-50 0.8 15-20 0.3 51-56 0.9 21-26 0.4 57-60 1.0 27-32 0.5 EMT. NALCOMIS, through the internal clock, will automatically calculate EMT EMT does not include the clock hours and tenths for cure time, charging time, or leak test when they are being conducted without maintenance personnel actually monitoring the work. Although the EMT is directly related to

job man-hours, it is not to be confused with total man-hours required to complete a job, for example, if three men worked together for 2.5 hours to make a repair, the total man-hours would be 7.5 hours and the EMT would be 25 hours TECHNICAL DIRECTIVE ID. Enter the 12 or 13 characters that identify the specific TD incorporated or being incorporated in the type equipment. This field is divided into seven sections as follows: INT. Enter an X to indicate an interim TD; otherwise leave blank CODE. Enter the two-character numeric code that denotes the type of directive being incorporated TD codes are in Appendix E. BASIC NO. Enter the four numeric characters identifying the basic TD, preceded by a zero(s) to complete the field. RV. Enter the one alpha character that denotes the specific revision of the basic TD Leave blank if not applicable. AM. Enter the one numeric amendment number of the basic TD Leave blank if not applicable PART. Enter the two-character numeric part number as listed in

the TD Leave blank if not applicable. KIT. Enter the two-character alphanumeric number of the specific kit incorporated If no kit is required, enter 00 in this section. NOTE: TDs must be on file within NALCOMIS prior to TD MAF initiation. TYPE EQUIP. Enter the TEC that describes the end item on which work is being performed TEC structuring is explained in Appendix E. The specific TECs are identified in the NAVAIR Logistics web site TEC Translator (http://www.navairnavymil/logistics/tectranslator/) NOTE: The OOMA NALCOMIS application uses Assembly CDs as an expansion of the NAVAIR assigned TEC to further identify a specific end item within the TEC. Assembly CDs are used exclusively within the OOMA NALCOMIS application and are defined in Appendix E. BU/SERNO. Enter the bureau or serial number of the equipment or end item on which work is being performed. If more than six digits enter the last six; if less than six digits prefix with sufficient zeros to total six characters. This field

must not be blank Enter 0 in this field when using the MAF to document work on groups of like items, for example, jacks, stands, common aeronautical equipment, or items not identified by bureau/serial number. In cases of on-equipment work at the O-level for personal survival equipment, enter the first letter of the aircrewmans first and last name and last four digits of the social security number. 16-20 COMNAVAIRFORINST 4790.2C 15 Jan 2017 W/D. The WD code is a single alpha character that identifies when the need for maintenance was discovered. The three sets of WD codes that cover the equipment categories are: (1) aircraft and engines; (2) SE, PME, and expeditionary airfield; and (3) missiles/missile targets. T/M. Enter the one-character alpha or numeric code used to describe the type of work being accomplished, for example, scheduled, unscheduled, supply support. Definitions and explanations of these codes are in Appendix E. POSIT. Enter POSITs which are used to evaluate

performance/logistics characteristics between identical components. For NALCOMIS application users, POSITs are included in applicable WUC manuals and are identified by a double asterisk (*) preceding the WUC. The OOMA NALCOMIS application identifies POSITs as a separate data element within the applicable baseline. When a component has been identified as position sensitive, it shall be mandatory that the POSIT be documented in block A60 of the MAF. Identifiers are categorized into two groups as follows: General Position Codes. A two digit alphanumeric code which indicates a specific location by use of plain language: LH/RH - Indicates left-hand or right-hand installation, such as main landing gear components, tires, side by side cockpit, and components. FW/AF - Indicates fore and aft positions such as tandem cockpit components. UP/LW - Indicates upper or lower positions, such as anticollision lights or antennas. PR/SC/AL - Indicates primary, secondary, or alternate positions, such as

hydraulic components or multiple avionics component installations. 01, 02, 03, 04 - Indicates positions using a sequential numbering system, such as helicopter rotor dynamic components or a numbering system used to identify the position of fuel nozzles on a gas turbine engine. Specific Position Codes. A two digit alphanumeric code which indicates a specific location using alphanumeric sequencing: A1 - Bleed Valve, Stg 5, 2 oclock, #1 engine. B1 - Bleed Valve, Stg 5, 4 oclock, #1 engine. A2 - Bleed Valve, Stg 5, 2 oclock, #2 engine. B2 - Bleed Valve, Stg 4, 4 oclock, #2 engine. FID. Leave blank, reserved for future use (Under development) SFTY/EI. Enter the locally assigned four digit control number from the NAMDRP Report Control Number. METER. This field is mandatory when TEC for on-equipment work is G, H, or S and maintenance level is 1. SE FSCM. CAGE of the end item of SE (optional) TECH. Enter an N for all maintenance actions involving Engineering and Technical Service (ETS)

support. INV CD. Enter the one digit inventory code that describes the status of the equipment during the transaction (Appendix F). 16-21 COMNAVAIRFORINST 4790.2C 15 Jan 2017 PERM CD. Enter the six digit PUC of the organization completing the transaction (aircraft only) REPAIR CYCLE RECD. Date and Time NALCOMIS generated upon MAF initiation IN WORK. Enter Julian date and time COMP. Enter Julian date and time completed AWAITING MAINTENANCE HRS. Enter the appropriate AWM reason code for the related maintenance action. Order of significance may be determined by local policy MAINTENANCE/SUPPLY REC. NALCOMIS tracks and documents all awaiting maintenance/ supply time. This is calculated by the internal monitoring of job status as related to supply status/ maintenance status. REMOVED/OLD ITEM. These fields are completed in NALCOMIS using the appropriate function, when a repairable component is removed from the end item or major component on which work is being performed. Enter the CAGE,

SERNO, and P/N or lot number for the CART, CAD, or PAD. If the SERNO is more than 10 characters, enter the last 10 If the P/N is more than 15 characters, enter the last 15. (For Optimized NALCOMIS the SERNO and P/N field is limited to a maximum of 15 and 32 characters respectively.) Enter the time/cycle, preceded by an alpha character as listed in Appendix E. For warranty items, use the second time/cycle field, enter a W, followed by four digits to indicate the length of the warranty period in time/cycles, or the date of warranty expiration. Information about warranty length and expiration date can be found on the data plate affixed to the item, or in its logbook or associated records. If the current time/cycles figure for an item is greater than the specified warranty length of that item, no W entry should be made since the item is no longer under warranty. In the third time/cycle enter an X, followed by the last four characters of the contract number. The contract number can be found

on the data plate affixed to the item, or the logbook or associated records, or NTCSS Optimized NALCOMIS CM ALS records. INSTALLED/NEW ITEM. These fields are completed in NALCOMIS using the appropriate function, when a repairable component is installed on the end item or the major component on which work is being performed. Enter the CAGE, the SERNO and P/N or lot number for the CART, CAD, or PAD. If the serial number is more than 10 characters, enter the last 10 If the part number is more than 15 characters, enter the last 15. (For Optimized NALCOMIS the SERNO and P/N field is limited to a maximum of 15 and 32 characters respectively.) Enter the time/cycle preceded by an alpha character listed in Appendix E. For warranty items, use the second time/cycle field, enter a W, followed by four digits to indicate the length of the warranty period in time/cycles, or the date of warranty expiration. Information about warranty length and expiration date can be found on the data plate affixed to

the item, or in its logbook or associated records. If the current time/cycles figure for an item is greater than the specified warranty length of that item, no W entry should be made since the item is no longer under warranty. In the third time/cycle enter an X, followed by the last four characters of the contract number. The contract number can be found on the data plate affixed to the item, or the logbook or associated records, or NTCSS Optimized NALCOMIS CM ALS records. DISCREPANCY. Enter a narrative description of the reported discrepancy and the System Reason Field. PILOT/INITIATOR. Enter the person’s name and rank who discovered the discrepancy CORRECTIVE ACTION. Enter a narrative description of the corrective action taken to correct the discrepancy. 16-22 COMNAVAIRFORINST 4790.2C 15 Jan 2017 NOTE: If a fleet engineering disposition (FED) request has been initiated per Chapter 3, include the FED reference number provided by the ISSC engineering authority in the corrective

action field. Also, reference the FED authorization for repair or BCM disposition provided by ISSC. The ISSC shall include instructions for any required logbook or SRC card entries with the disposition. CF REQ/RFI. This is a dual purpose field for use by the O-level and I-level activities The O-level will enter an (x) if a check flight is required after completion of the maintenance action. The IMA will enter an (x) if the repair action is RFI. QA REQ/BCM REQ. This is a dual purpose field for use by the O-level and I-level activities The O-level will enter an (x) if the maintenance action requires a QAR inspection. (Not applicable to CDI inspection.) The IMA will enter an (x) if the repair action is BCM RFI or BCM. NALCOMIS will update this data field based on the action taken entry CORRECTED BY. Once the logged on person gives a job status of JC, NALCOMIS will automatically post the workers name to the corrected by field of the MAF. At this time, the Hard Copy Notice (HCN)/MAF is

closed to the worker and the MAF clearing cycle has begun. INSPECTED BY. The CDI/QAR will use the appropriate function to indicate approval of a specific MAF. NALCOMIS will electronically post the CDI/QARs name to the MAF based on the logged-on person. SUPERVISOR. The supervisor will use the appropriate function to indicate approval of a specific MAF. NALCOMIS will electronically post the supervisors name to the MAF based on the loggedon person This indicates all tool control requirements have been complied with MAINT CONTROL. The Production Controller will use the appropriate function to indicate approval of a specific MAF. NALCOMIS will electronically post the controllers name to the MAF based on the logged-on person. JCN. Using the appropriate function, enter the assigned JCN per paragraph 161 In the case of a maintenance action being performed on transient aircraft (Navy or non-Navy), the first three positions of the JCN are always the organization code of the aircraft reporting

custodian. NOTE: For subcustody SE in the custody of another department that requires repair by the IMA the JCN will be auto assigned by NALCOMIS upon Production Control approval, reflecting the IMAs organization code. WORK CENTER. Enter the appropriate work center code performing the maintenance action described on the MAF. Work center codes are listed in Appendix E STATUS. For level 1 maintenance only, enter "U" for up discrepancy and "D" for down discrepancy. This data field may be updated using appropriate update function INSPT JCN. Used for power plants engine induction PRI. Production Control or authorized personnel will fill in this data field to approve the initiated MAF using the appropriate function. SYSTEM/REASON. Enter a brief (snap shot) description of the reported discrepancy using the appropriate function. MCN. Serial number assigned to each maintenance action 16-23 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.22 Support Equipment (SE), Training

Devices, Missile Target Documentation 16.221 Documentation Collection Method This paragraph prescribes the method for collecting maintenance, inventory, and utilization data on equipment. This information is used to evaluate equipment reliability and maintainability, and provide data for engineering analysis to improve or replace equipment. The term SE encompasses all SE including that commonly known as yellow gear, test sets and benches, run-up stands, diagnostic equipment, PME, and equipment used to maintain aircraft, aircraft components, or SE, such as drill presses, lathes, grinders, sewing machines, or welders. These items of SE are identified by D, G, H, and S series TECs Support equipment gas turbine engine (SEGTEs) are identified by P series TECs. Items of SE may be inventoried using Inventory Code 0. The source documents used are MAFs and METER Cards NOTE: Training devices and missile targets require inventory reporting only. 16.222 Terms and Data Field Definitions The

following defines terms and describes data fields and procedures of special interest to SE documentation: 16.2221 Utilization End item utilization is accounted for by entering a five-position meter reading in the METER field of the MAF any time on-equipment work is performed on SE. If the equipment has a meter that records end item utilization, the whole hours (no tenths) or starts/cycles from the meter are preceded by the letter M or S (as appropriate) and enough zeros to make a five position entry. If the equipment does not have a meter, enter A0000. This field will be left blank when performing offequipment work 16.2222 MEASURE is a data processing system for recall and scheduling of test, measuring, and diagnostic equipment into calibration facilities. The PME Work Center (670) documents all calibration and repair on a METER Card per the OP43P6B user’s manual issued by COMNAVAIRSYSCOM. For MAF documentation in support of PME actions, refer to paragraph 16.2211 16.2223 The AMMRL

Program collects data to establish SE requirements, distribute assets, and provide a base for SE budgeting requirements. Outputs of the AMMRL Program are the SERMIS and IMRL The AMMRL Program is defined in NAVAIRINST 13650.1 16.223 SE Maintenance Actions The following prescribes the method of documenting SE maintenance actions using NALCOMIS. 16.2231 Standard HCN/MAF Procedures Figure 16-12 illustrates the types of VIDS/MAFs required for SE, training devices, and missile target documentation. a. On-Equipment Work The discrepancy MAF initiation function will be used to initiate MAFs for on-equipment work performed on an end item of SE, except for calibration. (Refer to paragraph 162211 for calibration documentation.) If no repairable component is removed, the worker will initiate the MAF using the appropriate update function. Paragraphs 16251 through 16258 show on-equipment documentation. On-equipment work requiring MAF initiation are: (1) Repairing an end item. (2) Removing a

repairable component from an end item for any reason, including calibration. (3) Compliance with a TD on an end item. 16-24 COMNAVAIRFORINST 4790.2C 15 Jan 2017 (4) Inspecting an end item. (5) Documenting preservation or depreservation. (6) On-equipment cannibalization. b. O-Level IMRL Reportable SE A MAF is used to induct O-level SE into the IMA for repair, periodic inspection, and TD compliance (paragraph 16.259) A requesting activity delivers the MAF and SE to the IMA. Production Control signs the MAF acknowledging receipt of the SE Use the appropriate function inducting the item creating a MAF. c. Turn-In Document NALCOMIS will generate a MAF once the repairable component ordered is approved using the Material Approval Process, this turn-in will have the same JCN as the end item, except components removed for calibration. If the component is from supply stock, the turn-in document will reflect the supply JCN per paragraphs 16.2510 and 162511 If the component is removed from an

end item, the document will be generated by NALCOMIS for the work center that removed it. A turn-in document is required even when the maintenance on the removed component is performed by the same person or shop that removed it. d. Removed Repairable Component Processing Maintenance actions on a removed repairable component are off-equipment work and documented by completing the HCN/MAF (paragraph 16.2512) 16.2232 Suffix MAF NALCOMIS will generate a HCN/MAF for each repairable subassembly approved in the Material Approval Function. Each additional MAF will be automatically assigned a suffix to the same JCN (paragraph 16.2513) used for the original maintenance action, per paragraph 161 A suffix is required, even when the maintenance of the removed subassembly is performed by the same person or shop that removed it. a. Removed Repairable Subassembly When ordering or documenting the removal of a repairable subassembly in NALCOMIS the user must indicate repairable subassembly by entering a

(Y) for yes in the appropriate field. This allows NALCOMIS to set up the appropriate JCN logic for the MAF If no repairable sub-subassemblies are removed, this is the last document required (paragraph 16.2514) b. Removed Repairable Subassembly If repairable sub-subassemblies are removed, repeat the procedures in paragraphs 16.2231d and 162232 above 16.224 Support Equipment (SE) Repair Action The repair action is the maintenance action documented on the MAF. The repair is the correction of a discrepancy or the declaration that a discrepancy did not exist. The term "documented in the normal manner", used throughout this section, refers to repair action documentation procedures. 16.225 Support Equipment (SE) Inspections and Periodic Maintenance 16.2251 All inspections (except preoperational and postoperational), PM, and preservation/depreservation actions are documented using NALCOMIS Inspection Control MAF initiation procedures (paragraph 16.2515) 16.2252 MRC An MRC describes

an inspection or PM action that must be performed at a specified interval or situation. A group of MRCs comprising one inspection is commonly referred to as an MRC DECK. 16-25 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2253 Look Phase MAF Procedures Look phase MAFs (paragraph 162516) are used to document inspection and PM actions dictated by MRCs. WUC 030 is used for inspections occurring on a one time basis, such as acceptance, transfer, and conditional. All other inspections will be documented using WUC 030000 with the seventh position assigned per Appendix E based on the interval of the inspection. 16.2254 For JCN structure refer to paragraph 161 16.2255 Fix Phase Refer to paragraph 162517 16.226 Support Equipment (SE) Corrosion Documentation 16.2261 Corrosion prevention and treatment of SE is performed as part of a scheduled maintenance requirement or as an unscheduled maintenance action. 16.2262 Corrosion prevention requirements found while complying with MRCs (scheduled

maintenance) will be documented on the inspection look phase MAF. This includes SE washing performed as part of a scheduled inspection. 16.2263 Corrosion treatment requirements found during the look phase of an inspection will be documented on a fix phase MAF. Use AT Code Z and Malfunction Codes C01 through C33 The treatment of bare metal is included in this category. 16.2264 All unscheduled corrosion prevention is documented on a MAF Unscheduled SE cleaning and temporary repairs of bare metal are included in this category. Multiple items processed may be documented. Use Work Unit Code 040, AT Code 0, Malfunction Code 000, WD Code O, and TM Code D. 16.2265 Unscheduled corrosion treatment actions are documented on the MAF using AT Code Z and Malfunction Codes C01 through C33. 16.227 Support Equipment (SE) Preservation and Depreservation 16.2271 MAFs are used to document preservation/depreservation of end items per NAVAIR 17-1-125 and NAVAIR 15-01-500. 16.2272 When Production Control

approves the preservation/depreservation MAF, NALCOMIS will automatically assign a numeric serial number JCN. This MAF will be used as the control document WUC 049 and TM code D will be used. 16.2273 Upon completion of the preservation/depreservation action the control document will be processed by Production Control with 1 item processed entered in the items processed field of the MAF. 16.2274 MAFs are issued to each work center participating in the preservation/depreservation action If only one work center is involved in preservation/depreservation action, man-hours may be accounted for on the control document. 16.228 Support Equipment (SE) Technical Directive (TD) Compliance 16.2281 TD compliance is documented on the MAF (paragraphs 162518 through 162522) Production Control schedules all TD compliance actions and initiates all TD compliance MAFs except TD compliance turn-in documents for modification of supply stock. A numeric JCN is assigned to a TD compliance action per paragraph

16.1 A separate MAF with the same JCN is initiated for each work center involved. 16-26 COMNAVAIRFORINST 4790.2C 15 Jan 2017 NOTE: TDs must be on file within NALCOMIS prior to TD MAF initiation. 16.2282 Figure 16-36 shows the types of TD compliance VIDS/MAFs used to document TDs that apply to end items, for example, an NC-8A power unit or ALM-157 test set. If a component is removed for offequipment inspection or modification, in compliance with an end item TD, the TD compliance VIDS/MAF documenting the end item TD compliance accounts for man-hours and elapsed maintenance time (EMT) expended removing and reinstalling the component. A separate TD compliance VIDS/MAF is required for each component removed. 16.2283 Figure 16-37 shows the types of VIDS/MAFs used to document TDs that apply only to a component, for example, a gear box or test set module. When an RFI component is removed for offequipment inspection or modification in compliance with a component TD, a TD compliance

supporting MAF is generated to account for man-hours and EMT expended removing and reinstalling the component. A separate VIDS/MAF with a different JCN is required for each component removed, and a TD compliance turn-in document is generated (Figure 16-33). 16.2284 Figure 16-38 shows the types of VIDS/MAFs used when a failed component is removed as part of an end item TD. The end item TD compliance MAF accounts for the man-hours and EMT expended removing and replacing the component. 16.2285 Figure 16-39 shows the types of VIDS/MAFs used when a failed component is removed in conjunction with a component TD. The on-equipment repair action VIDS/MAF accounts for the manhours and EMT expended removing and replacing the component Two turn-in documents are required; one to initiate the TD compliance action, and one to initiate the repair action. If the component was originally removed on a TD compliance facilitate MAF, the TD facilitate VIDS/MAF is converted into a repair action VIDS/MAF by

identifying the removed component in the removed/old item section, changing the AT Code to R, and ordering a replacement component. Documentation then continues in the normal manner of a repair MAF per paragraph 16.224 16.229 Support Equipment (SE) Inventory Reporting Procedures 16.2291 The SE inventory reporting system provides the SE reporting custodian with a list of major assets on hand. SE may be inventoried using an inventory code of 0 These reporting system requirements are in addition to the AMMRL Program and do not negate the reporting requirements published in NAVAIRINST 13650.1 16.2292 Definition of Terms The following terms are used throughout this section in describing how to document inventory transactions. a. Controlling Custodian SECAs are responsible for fleet distribution and management of SE assets b. Reporting Custodian Reporting custodian is the activity (usually I-level) having primary custody of the SE as indicated on the IMRL. c. Inventory Codes (1) Inventory

status codes define the reporting requirements and current status of SE in the inventory reporting system. Inventory codes are listed in Appendix E (2) Utilization Reportable. All equipment listed in Mission Essential Subsystem Matrix (MESM) (provided on CNAP Share portal) require utilization reporting. Inventory Code 0 applies to training devices and missile targets that are inventoried but for which no mission capability data is collected. 16-27 COMNAVAIRFORINST 4790.2C 15 Jan 2017 d. Transaction Codes Inventory transactions are described by the transaction codes in Appendix E (1) Inventory Gain (Transaction Code 00). An inventory gain is the receipt of an SE unit into inventory reporting by a reporting custodian. SE and missile targets will be gained with an inventory status of 0 only. (2) Inventory Loss (Transaction Code 03). An inventory loss is when a reporting custodian transfers an SE unit or strikes it from naval service. An inventory loss is documented only if the unit

has previously been gained and is in the inventory system. (3) Implementation. SE inventory reporting by an activity that is not currently using the MAF for inventory control. The implementation date is normally the first day of a reporting period (a) Prior to implementation, the reporting custodians Production Control generates a list of all assigned SE that requires utilization reporting. This list contains: 1. Organization code. 2. Equipment TEC. 3. Equipment serial number. 4. Equipment inventory code (Appendix E). 5. Equipment meter reading. (b) Production Control prepares MAFs for all reportable equipment. (c) The SSCA generates a machine prepared listing and returns a minimum of two copies to Production Control for distribution. (d) Production Control reviews the lists for completeness and accuracy. Corrections will be made by normal submission of proper source data (Chapter 14). (e) The SSCA will correct the master file. (4) Inventory System Documentation Procedures

(a) The following lists the codes necessary to properly document inventory transactions: Transaction Code Inventory Code Inventory Transaction 00 0 Gain into inventory of an equipment that is inventoried but for which no mission capability data is collected. These items will only be gained or lost and will require no change in material condition reporting status (MCRS) reporting. This code is used for SE, training devices, and missile target inventory reporting and is not applicable to aircraft. 03 0 Loss from inventory of equipment that is inventoried but for which no mission capability data is collected. These items will only be gained or lost and will require no change in MCRS reporting. This code is used for SE, training devices, and missile target inventory reporting and is not applicable to aircraft. (b) Examples of MAFs used to document equipment gain or loss are in paragraphs 16.2523 and 162524 16-28 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2210 Change of Reporting

Custodian All maintenance actions are terminated when an equipment transfer involves a change of reporting custodian. This is done by completing the maintenance action on the completed line as of 2400 on the date of the equipment transfer. Transaction Code 11, AT Code N, and 0 items processed will be used The only name required is that of the supervisor. Refer to paragraph 16229 for a description of inventory procedures required for the change of reporting custodian. 16.2211 Calibration Actions 16.22111 METER Card PME Work Center (Work Center 670) of activities participating in the MEASURE Program documents all calibration and repair actions on the METER Card per OP43P6B. A METER Card is initiated as a turn-in document for any end item or component processed to the PME Work Center for any reason. The provisions of this paragraph are not applicable to any maintenance actions performed on the calibratable building blocks (BBs) of the any automatic test equipment (ATE). These maintenance

actions, including those incident to an off-line or on-line calibration action, shall be documented on the MAF. The calibration actions associated with any calibratable ATE BB shall be documented on the METER Card. 16.22112 MAF The MAF is used by work centers, other than precision measuring equipment (PME), to document all maintenance actions except calibration. When a component is removed from an end item for processing to the PME Work Center (for calibration or repair), a supporting MAF is generated to account for man-hours and EMT expended removing and reinstalling the component. A separate MAF with a different JCN is required for each component removed. Paragraph 162525 is an example of a MAF documenting the removal of a component for processing to the PME work center on a METER Card. NOTE: Only PME that requires parts to be ordered will be inducted using NALCOMIS procedures. All other repair actions will be completed on the METER Card. NO EXCEPTIONS 16.23 Aeronautical Component

and Item Documentation Procedures When processing repairable components and locally repaired consumables, a MAF is used to document removal and subsequent IMA processing. These procedures will also apply to consumable components that are inducted into the IMA for repair. The MAF will be completed per paragraph 16213 and submitted for processing even though the removal, repair, and reinstallation of a component occurs within a single work center. 16.231 Component Repair 16.2311 If administrative screening of the turn-in component (paragraph 162526) reveals that check, test, and repair capability exists or the repair capability has not been established within the IMA, the screening unit will notify the IMA Production Control that the component is available for scheduling into the appropriate work center for screening and repair. The screening unit will enter the Julian date the item was received in the RECD Field. When the screening unit is notified of the repair schedule for the

component by Production Control, the following information will be entered on the MAF. Paragraph 16.2527 is an example of a BCM action by AMSU a. Work Center Enter work center code of the work center assigned direct responsibility for repair of the component (Appendix E). b. Action Organization Enter the organization code assigned to the Intermediate Maintenance Activity (IMA). 16-29 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2312 The screening unit delivers the component and MAF to the appropriate work center The MAF remains open until final disposition of the component is known. Any supporting documentation will be done on additional MAFs. Some of the situations requiring supporting documentation are: a. Close Out A close out of incomplete maintenance actions may be required by local managers for the end of each reporting period. Each maintenance action will be closed out as of the last day of the reporting period or upon transfer of the equipment. b. Work stoppages due to a lack

of parts c. Troubleshooting When it is necessary to separate troubleshooting man-hours from repair manhours, the troubleshooting man-hours are accounted for on a separate MAF The existing MAF remains outstanding until the repair action is completed. Documentation of failed/required material and removed or installed items is done only on the repair action MAF (paragraph 16.2528) d. Assisting Work Centers Supporting the Basic Repair Action When more than one work center works on the same maintenance action, one work center is designated the primary work center and the other work centers are assisting work centers. The primary work center will generate a separate MAF for each assisting work center with the same JCN and WD Code V. If the assisting and primary work centers work on the same WUC item, the assisting work center accounts for 0 items processed. Assist MAF documentation will be to the work center that the personnel performing the task are permanently assigned regardless of the

physical location of the repair station (paragraphs 16.2529 and 162530) 16.2313 If repairable subassemblies or modules are faulty, a new MAF is initiated for each subassembly or module per paragraph 16.2531 a. Suffix and Double Suffix MAF For each removed subassembly, module, or sub-subassembly, document per paragraphs 16.213, 162532, and 162533 b. Material Requisitioning When a demand is placed on supply for a replacement subassembly, module, or sub-subassembly using the suffix or double suffix JCN, NALCOMIS will enter the JCN on the DOD Single Line Item Requisition System Document (DD 1348) issue document that is generated at ASD. This action is necessary to establish the requirement for a local repair cycle asset of subassemblies and modules to stock PEBs. The suffix or double suffix MAF is forwarded to Supply, with the remainder of the suffix or double suffix MAF processed the same as for any repairable item. 16.2314 Failed/Required Material The requirement for repairable

subassemblies, modules, or subsubassemblies will be recorded in this field of the original (major component) or subassembly MAF per paragraph 16.213 with the following additional requirements: a. Project Enter the MILSTRIP project code assigned by Production Control b. Priority Enter the MILSTRIP priority assigned to the material requisition c. Date Ordered NALCOMIS generated d. Requisition Number NALCOMIS generated e. Date Received NALCOMIS generated 16.2315 Retain the major component, subassembly, or module MAF In the case of an AWP situation, the major component, subassembly, or module MAF will be forwarded with the defective component to the AWP unit. 16-30 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2316 When it becomes necessary to transfer a repairable item off ship or station because of a lack of parts (BCM-4), the unavailable items are entered in the Failed/Required Material fields and Maintenance/Supply Record fields will be completed to reflect AWP time. Use of AT Code 4 is

restricted to occasions when the same AT code is entered for a major assembly identified by the WUC. Complete the MAF via normal MAF clearing cycle. When the maintenance action is completed, the Work Center Supervisor gives the component, the MAF, and material condition tag to the material delivery representative, and retains a copy of the MAF for MDR verification. 16.2317 Cannibalization Any order to cannibalize must come from Production Control who will issue and approve a cannibalization action for the removal and replacement of a component being cannibalized. Document cannibalization actions per paragraphs 16.2534, 162535, and 162536 16.2318 Matched Set The repair of matched sets will be documented in the same manner shown in paragraph 16.2537 16.2319 Tire and Wheel Documentation The built up tire and wheel assembly will be turned into IMA on a MAF turn-in document. When documenting the built up wheel and tire assembly, it is treated as a major repairable component with repairable

subassemblies. In the event a wheel assembly is found to have different SERNOs on each wheel half, the SERNO of the valve core half will be used for control and documentation purposes. Man-hours for routine processing of the wheel, such as cleaning and painting, will be documented on the turn-in MAF. NDI will be documented on an assist MAF A MAF work request prepared by supply will be required when a wheel assembly replacement must be built up to replenish supporting supply activity pool. The Work Center Supervisor will inspect the tire to determine serviceability. If unserviceable, the tire carcass will be marked for retread or scrap and BCM Code 1 or 9 used (as appropriate) (paragraph 16.2538) NOTE: The unserviceable tire will be returned to supply and identified with the appropriate code to indicate retread or scrap. Supply will establish a pool based on the appropriate wheel assembly, part numbers, stock numbers, or pool index numbers. All requests will be against this number.

Supply shall pre-expend or subcustody tires to the tire shop as required Tires requisitioned on a one-for-one basis shall be ordered using the Failed/Required Material Fields of the MAF. Enter AT Code R for tires that are categorized as repairable and must be accounted for on the turn-in MAF. A turn-in suffix MAF is generated automatically for each tire that is BCM. 16.23110 Battery Documentation Batteries will be turned in to the IMA on a MAF turn-in document They will be documented as follows: a. Batteries received for scheduled maintenance and not requiring maintenance other than servicing, use Transaction Code 31, AT Code A, and MAL Code 804. b. Batteries received for repair or scheduled maintenance and requiring maintenance other than servicing, use Transaction Code 31 or 32, AT Code C, and an appropriate MAL Code. c. EMT does not include the clock hours for charging time when maintenance personnel are not actually monitoring the work. 16.23111 Inter-IMA Support In some instances

an IMA will be required to transfer NRFI repairables to another IMA for repair, such as post deployment off-load by a carrier IMA, or shipment of a BCM item to an IMA known to have repair capability. Documentation procedures in these instances are as follows: a. Transferring IMA Close Out (post and predeployment) Paragraph 162539 is an example of a MAF for post and predeployment close out. 16-31 COMNAVAIRFORINST 4790.2C 15 Jan 2017 (1) Close out the original MAF, entering the appropriate AT Code (Appendix E) and any manhours and EMT expended prior to transfer. In the case of post deployment off-load, use of AT Code D is mandatory, whether the item was AWP, AWM, or IN WORK at the time of off-load. In other instances, a BCM Code will ordinarily be appropriate. The MAF will be submitted by the transferring IMA for processing; a copy of this MAF will accompany the item to the AMSU or AWP unit and will be shipped with the component to the receiving IMA. (2) WRAs must have all D-level

repairable SRAs installed prior to closing out the MAF for shipment to the receiving IMA. Likewise, SRAs with attaching D-level repairable SSRAs must have attaching SSRAs installed prior to closing out the MAF for shipment of the SRA to the receiving IMA. (3) WRAs missing FLR components will have such components installed prior to closing out the MAF for shipment to the receiving IMA provided the component is still available. Otherwise, document the missing FLR component per the following paragraph. (4) When a field level repairable SRA has been removed from the WRA and no replacement SRA is installed prior to off-load, document the close-out (original) MAF as follows: Failed/Required Material Index - Enter H-Z for each "missing" module, subassembly or sub-subassembly (as appropriate). Failed Part - Enter an X (as appropriate). Awaiting Parts - Enter an X (as appropriate) AT code - Enter P MAL, FSCM, Part Number, Ref Symbol, Qty, Date Ordered, Requisition Number - Enter

appropriate data to identify the missing unit. Date Received - Enter date the requisition was cancelled Transaction Code Enter 32 (5) On turn-in MAF, ensure FSCM, PN, Ref Symbol, Qty, Date Ordered, and Ref Number of HZ field are filled in for each "missing" module, subassembly, or sub-subassembly (as appropriate). NOTE: To allow for proper supply documentation ensure CCS is notified of missing FLR SRAs from the WRA to be shipped off-station. Supply shall cancel any off-ship/station requisitions for missing FLRs prior to closing out the MAF. The importance of proper documentation cannot be overemphasized. b. Receiving IMA Reinitiation Document Paragraph 162540 is an example of a reinitiated MAF from a transferring IMA. Upon receipt of a repairable item from another IMA, receiving AMSU will forward a copy of the MAF to the local supply CCS. Subsequent repair/disposition will be documented on the new MAF per paragraph 16.213, except that the RECEIVED DATE field will reflect

the date the component was received from the transferring IMA. 16.23112 Receipt of Unsatisfactory Material from the Supply Department When components received from supply prove unsatisfactory, these procedures will be followed. a. Component received, installed, and determined to be NRFI: (1) Complete original MAF, Failed/Required Material fields. (2) Requisition a replacement component using original MAF, Failed/Required Material Fields. NALCOMIS will automatically generate a turn-in document to accompany the NRFI component. Ensure the MAF is completed per paragraph 16.213 with the following exception: WD CODE field must be "Y" (received bad from Supply). b. Component received NRFI (not installed) or improper replacement received Turn-in the NRFI/improper component to the AWP unit. The AWP unit will prepare a DOD Single Line Item Release Receipt Document (DD 1348-1) using Record Type 62 for return of the material to Supply Response Section (SRS). Ensure all accompanying

documentation, for example, RFI tag, SRC Card, and MAF are returned with all items. 16-32 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.23113 Component Received Missing SRC Card, ASR, MSR, or AESR Components, assemblies, or equipment received from supply missing SRC cards, ASRs, MSRs, or AESRs shall be considered as NRFI and turned in on a DOD Single Line Item Release Receipt Document (DD 1348-1) prepared by Material Control. If the component is installed and cannot be determined to be new, it shall be considered as faulty Paragraph 16.2541 is an example of a MAF documented for turn-in of a component that is missing the SRC card. Items missing ASRs, MSRs, or AESRs should be documented in a similar manner NOTE: If the determination can be made that the component is in fact new, an SRC Card, ASR, MSR, or AESR will then be initiated by the requisitioning activity. 16.23114 Corrosion Supporting MAF Documentation of man-hours expended for corrosion prevention during the repair of WRAs/SRAs

are considered part of the repair process and are included on the repair MAF (paragraph 16.2542) 16.23115 Processing of Items Not Having a WUC or Not Identifiable to a Specific Type Equipment The maintenance effort in check, test, servicing of items or equipment for which no WUC exists or that cannot be identified to a specific TEC is documented as described in paragraph 16.232, MAF Work Request. 16.23116 Repair of Supply Assets The repair of supply assets will be documented in the same manner as discussed in paragraph 16.213 with the following exceptions: a. The local supply department will initiate a MAF completing all required data elements b. JCN assignment will be made by the Supply Department using the organization code assigned to the Supply Department, for example, A8D or C84. Refer to Maintenance Data VALSPEC in Appendix F c. When in receipt of an applicable TD for compliance, the Supply Department, working with the IMA QA, will screen all assets to ensure modification

incorporation (where applicable). d. The IMA Production Control and Supply will schedule applicable/required maintenance actions in a timely manner. Paragraph 162543 is an example of the MAF documented for an end item turned in from a supply activity for TD compliance. 16.232 Maintenance Action Form (MAF) Work Request 16.2321 The MAF Work Request is used to document man-hours expended in support of work or assistance that is beyond the requesting activitys capability and does not involve repair of aeronautical material. It is used primarily for, but is not limited to, the following: a. Inducting items from supply for buildup, such as engines and propellers b. Inducting items not having a WUC or not identifiable to a specific type equipment for check, test, service, manufacture, or fabrication. c. Requesting NDI either on-site or at the IMA when a TD is not involved NOTE: Work requests for items removed for local manufacture or fabrication must be approved and signed by the requesting

activitys Maintenance Control Supervisor and the supporting activitys Production Control Supervisor. Batteries received for check, test, or service will be documented per paragraph 16.2324 ALSS and AEP will be documented per paragraph 16.2325 16.2322 Examples of MAF Work Requests are in paragraphs 162544 through 162552 16-33 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2323 This and subsequent paragraphs outline the procedures for documentation and processing of maintenance requirements when approved and signed by both the requesting activitys Maintenance Control Supervisor and the supporting activitys Production Control Supervisor or their authorized representatives. Upon receipt of the MAF work request and item(s), Production Control will sign a copy of the MAF work request, acknowledging receipt of the item(s), and return it to the originating activity. Upon completion of check, test, or manufacture, the work center will notify Production Control of job completion. A copy of the

MAF will be attached to the item(s) and routed to Production Control who will notify the originating activity that the item(s) is/are ready for pickup. Production control will issue the item(s), with a MAF attached to the item(s) and inform the originating activity that the item(s) is/are ready for pickup. 16.2324 Items completing check, test, or local manufacture will be processed as described in paragraphs 16.2544 through 162552 16.2325 ALSS/AEP MAF Documentation Procedures ALSS/AEP will be turned into the I-level maintenance activity on a MAF turn-in document. They will be documented as follows: a. ALSS/AEP received for scheduled maintenance and not requiring maintenance, use Transaction Code 31, AT Code "A" and MAL Code 804. b. ALSS/AEP received for unscheduled or scheduled maintenance and requiring maintenance use Transaction Code 31 or 32, AT Code "C" and an appropriate MAL Code. c. EMT does not include clock hours for leak check time when maintenance

personnel are not actually monitoring the work. d. Requisition and turn-in procedures for ALSS/AEP assemblies and repair parts shall be per standard induction/requisition procedures. All turn-ins will be delivered directly to the respective pool work center. 16.2326 Examples of ALSS/AEP MAF documentation are in paragraphs 162553 through 162563 16.2327 Supply Asset Induction Used to induct supply assets for repair for items missing the material condition tag/history records (paragraphs 16.2564 and 162565) 16.233 Technical Directive (TD) Compliance 16.2331 If a TD is complied with at the O-level (on-equipment work), all maintenance actions will be documented using the MAF. 16.2332 If during compliance with a TD it becomes necessary to forward an item to the IMA for modification or inspection and return, the following procedures will be followed: a. If the IMA informs the O-level activity that the item requires repair, the O-level activity must initiate another MAF for turn-in and

requisitioning purposes using the original JCN and will be documented by the IMA. The outstanding TD compliance MAF originally provided to the IMA will be destroyed. After the repair action is complete, Production Control will then initiate a replacement TD compliance MAF using a supply JCN. b. Items processed in excess of 1 may be entered only when the TEC Field contains a code beginning with Y, D, S, H, or G or ending with 9 and is either a nonserialized item or does not include a part number change in the REMOVED/OLD ITEM or INSTALLED/NEW ITEM fields. Serialized items for which a 16-34 COMNAVAIRFORINST 4790.2C 15 Jan 2017 part number change is reflected in fields E or G must be accomplished on an individual TD compliance MAF. 16.2333 Examples of TD MAFs are in paragraphs 162566 through 162570 16.234 Recovery and Reclamation of Crash Damaged Aircraft 16.2341 General procedures and policies for recovery, reclamation, and transfer of crash damaged aircraft are in Chapter 5 and

OPNAVINST 3750.6 16.2342 Supply Department The Supply Officer notifies the supporting IMA that the aircraft is available for reclamation and provides the reclaiming activity with the Master Salvage List (MSL). No one, other than the I-level activity reclamation team, is allowed access to stricken aircraft. Disposition of components obtained from reclamation is performed by initiation of a MAF work request and induction of the defective component to the I-level activity. A copy of the MAF is retained in the CCS suspense file This MAF is annotated with the word "reclaimed" (paragraphs 16.2564 and 162565) When reclaimed components are returned from the IMA RFI, they are put in stock as a gain by inventory. If NRFI, they are shipped to a designated repair point. 16.2343 IMA When notified by Supply Department that a stricken aircraft is available for reclamation, the IMA assembles a team and reclaims all potential repairable components in addition to those listed in the current

MSL, as provided by the supporting Supply Officer. In addition, some usable consumable items may also be reclaimed. All components not reclaimable are destroyed to the point where they will not be accepted by the Supply Department for an exchange item. All salvaged components will be turned over to the supply department immediately, whether or not they are included on the MSL. Repair of salvaged components is documented on a MAF. 16.2344 Requests for stricken aircraft, components, or assemblies will be directed to the CO of the salvaging activity, marked Attention: Supply Officer. 16.2345 O-level activities that have NTCSS Optimized OMA NALCOMIS CM ALS records must coordinate with the Supply Department and IMA to ensure the integrity of NTCSS Optimized OMA NALCOMIS CM ALS records. Records must be properly stricken or removed from the aircraft NTCSS Optimized OMA NALCOMIS CM ALS records and transferred to the supply department for further documentation. 16.24 I-Level Engine, Auxiliary

Power Unit (APU), and Support Equipment Gas Turbine Engine (SEGTE) Maintenance Documentation Procedures 16.241 Documentation Procedures Documentation procedures are broken down into two parts; conventional engines (paragraphs 16.2571 through 16.25102) and modular engines (paragraphs 1625103 through 1625131) 16.242 Documentation Procedures Exceptions Documentation procedures, whether an aircraft engine, APU, or SEGTE are the same with the following exceptions: 16.2421 Failed/Required Material FSCM Field When identifying an APU or SEGTE always enter numeric 1 for engine position; for example, PHAB1. 16-35 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2422 Removed/Old Item or Installed/New Item FSCM Fields When identifying an APU or SEGTE always enter numeric 1 for engine position; for example, PHAB1. 16.2423 Removed/Old Item or Installed/New Item Time/Cycles Fields When documenting APU or SEGTE enter the engine hour meter or start counter reading (as appropriate). 16.243 Engine, APU, and

SEGTE Corrosion Documentation Corrosion prevention and treatment of engine, APU, and SEGTE is performed as part of a scheduled maintenance requirement or as an unscheduled maintenance action. 16.244 Corrosion Prevention Requirements Corrosion prevention requirements found while complying with MRCs (scheduled maintenance) will be documented on the inspection look phase MAF. 16.245 Corrosion Treatment Requirements Corrosion treatment requirements found during the look phase of an inspection will be documented on a fix phase MAF. Use AT Code Z and Malfunction Codes C01 through C33 The treatment of bare metal is included in this category. 16.246 All Unscheduled Corrosion Prevention All unscheduled corrosion prevention is documented on a MAF. Unscheduled aircraft cleaning and temporary repairs of bare metal are included in this category. Multiple items processed may be documented. Use Work Unit Code 040, AT Code 0, Malfunction Code 000, WD Code O, and TM Code D. 16.247 Unscheduled Corrosion

Treatment Unscheduled corrosion treatment actions are documented on the MAF using AT Code Z and Malfunction Codes C01 through C33. 16.248 Engine Repair 16.2481 Control Document The turn-in document will be retained as a control document until the repair is complete. 16.2482 All man-hours and EMT expended in accomplishing the repair will be documented on the MAF. 16.2483 The same JCN will be used for repair actions requiring the removal and replacement of consumable components and fix-in-place discrepancies. 16.2484 Suffix JCNs will be used for repair actions requiring the removal and replacement of repairable components. 16.2485 Examples of conventional engine repair documentation are in paragraphs 162571 through 16.2583 16-36 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.249 Major Engine Inspections 16.2491 Major engine inspections to be performed at the IMA fall into two categories; inspections on engines inducted for the sole purpose of inspection, and inspections subsequent to

repair. As part of the repair action the I-level activity must perform the next major inspection due using the criteria in this instruction. 16.2492 General instructions for documentation of major engine inspections are in the following paragraphs. 16.2493 Control Document a. For engines turned in solely for inspection, the turn-in document will serve as the control document for the inspection. b. For major engine inspections after repair, IMAs will initiate a MAF to serve as the inspection control document. The JCN will be provided by the O-level activity in the Discrepancy Field of the turnin MAF c. If only one work center is involved in the inspection, look phase man-hours and elapsed maintenance time may be entered on the control document. If more than one work center is involved, a supporting MAF must be documented for each work center involved in the inspection. d. The WUC for engine inspections will be constructed in the following manner: (1) First three positions will be 030.

(2) Fourth through sixth positions will reflect the hour level of the engine inspection (divided by 10) being performed. For example, a 900-hour engine inspection would be recorded in these positions as 090. (3) Seventh position is zero. (4) The WUC for a 900-hour engine inspection would be as follows: 0300900 e. When MRCs do not specify a specific interval such as, T56, F404, for a major inspection, the hour level will be calculated by multiplying the number of aircraft phases times the phase interval. As an example, for the T56-A-14, the WUC 0301200 would be used for the major inspection. 16.2494 Repair Document Job Control Number Fields Enter the same data elements as on the control document but with sequential numbering in the second and third positions of the serial number for example, A01, A02. If more than 99 numbers are required for this purpose, refer to paragraph 161 for additional information. 16.2495 Examples of major engine inspection documentation are in paragraphs 162584

through 16.2591 16.2410 Technical Directive (TD) Compliance 16.24101 It shall be the policy of the IMA to incorporate all immediate changes, within their capability, while the engine is in the possession of the I-level activity for repair. 16.24102 Technical Directive Compliance MAF Initiation TD compliance MAF initiation can be originated from three sources; supply activity, O-level, and I-level Production Control: 16-37 COMNAVAIRFORINST 4790.2C 15 Jan 2017 a. The supply activity originates the TD compliance MAF using a supply JCN for TD compliance on all engines or engine components held as supply stock. Examples of documentation are in paragraphs 16.2592, 162593, and 162594 b. O-level activities originate the TD compliance MAF using an O-level JCN for engines or engine components sent to the IMA solely for TD compliance. Examples of documentation are in paragraphs 16.2595, 162596, and 162597 c. I-level Production Control originates the TD compliance MAF for engines or engine

components inducted for repair which require TD compliance. Examples of documentation are in paragraphs 162598 and 16.2599 16.24103 O-level activities requesting assistance from the IMA in the incorporation of a TD shall use the procedures per paragraphs 16.25100, 1625101, and 1625102 16.2411 Modular Engine Repair Paragraphs 16.25103 through 1625117 are examples of repairs on modular engines and associated components. The TEC Field will reflect the equipment category and model/series of the engine For modules, the engine application series (fourth position) will be X, for example, the F404-GE-400 module would be TXAX. 16.2412 Modular Engine Major Inspections 16.24121 The major engine inspections to be performed at the IMA fall into two categories; the inspections on engines inducted for the sole purpose of the inspection, and inspections subsequent to repair. As part of the repair action the IMA must perform the next major inspection due using the criteria in this instruction. 16.24122

General instructions for documentation of the major engine inspections follow: a. Control Document: (1) For engines turned in solely for inspection, the turn-in document will serve as the control document for the inspection. (2) For major engine inspections subsequent to repair, the IMA will initiate a MAF to serve as the inspection control document. The inspection JCN will be provided by the O-level activity in the Discrepancy Field of the turn-in MAF. (3) If only one work center is involved in the inspection, look phase man-hours and EMT may be entered on the inspection control document. If more than one work center is involved, a separate supporting MAF must be documented for each work center involved in the inspection. b. The inspection WUC and repair JCN are described in paragraph 16249 16.24123 Examples of major engine inspection documentation are in paragraphs 1625118 through 16.25126 16.2413 Modular Engine Technical Directive (TD) Compliance 16.24131 It shall be the policy of

the IMA to incorporate all immediate changes, within their capability, while the engine is in the possession of the I-level activity for repair. 16-38 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.24132 All TDs for modular engines will be issued against the module 16.24133 WUC will be that of the module or component of the module but never the engine 16.24134 The TEC Field will reflect the equipment category and model/series of the engine For modules, the engine application series (fourth position) will be "X", for example, the F404-GE-400 module would be TXAX. If a component is being sent from supply for TD compliance, the TEC will be for the equipment category model/series with an X in the application series (fourth position), for example, an F404-GE-400 engine component separate from a module would be TXAX. 16.24135 If the TD applies to more than one module, a separate MAF will be issued for each module 16.24136 Transaction Code 41 will be used with modules that do not have

a part number change 16.24137 Transaction Code 47 will be used for either a module with a part number change or a TD incorporation on a component. Removed/Old Item Fields and Installed/New Item Fields will be completed. 16.24138 JCN will be that of the activity requesting the TD compliance 16.24139 When a complete engine is being turned in for a TD compliance, the propulsion system serial number (PSSN) will be reflected in the Discrepancy Field. NOTE: If an engine or engine component sent to the IMA for a TD compliance is found to require repair, the IMA will inform the O-level activity which must provide a turn-in MAF for documenting the repair action. The original TD compliance MAF is destroyed and Production Control initiates a replacement TD compliance MAF using a supply JCN. 16.241310 Examples of TD compliance on modular engines, modules, and their associated components are in paragraphs 16.25127 through 1625131 16.2414 Engine or Module Component Cannibalization Actions for the

I-Level Activities Production Control, when authorized by Supply, will initiate cannibalization actions for awaiting parts repair or not mission capable supply or partial mission capable supply situations. The removal of components for cannibalization and the replacement of components after cannibalization will be documented on one MAF using the procedure outlined in paragraph 16.25132 16.2415 Cartridges (CARTs), Cartridge Actuated Devices (CADs), and Propellant Actuated Devices (PADs) Documentation Replacement of installed explosive devices requires an individual MAF for removal and replacement of each device. The removal and replacement action will be documented in the REMOVED/OLD ITEM and INSTALLED/NEW ITEM blocks using Transaction Code 18 or 19 (as appropriate). The WORK UNIT CODE block (A22) shall reflect the WUC that is assigned in OOMA NALCOMIS baseline or, for NALCOMIS users, obtained from the WUC manual. The PART NUMBER blocks (E23 and G23) shall reflect the lot number of the

devices being removed and installed. TIME/CYCLES blocks (E42 and G38) shall have an entry using Time/Cycle Prefix Code H and the container open date for CARTs or CADs and the propellant manufacture date for PADs. An example is in paragraph 1625133 16-39 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25 Documentation Explanations 16.251 End Item Repair (No Removed Component) Figure 16-13 is an example of a VIDS/MAF documented when repairing an end item if no repairable components are removed. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 11 or 12. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate

AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed; first position must be D,G,H,M,S,V, or Y. BU/SERNO - Enter the appropriate bureau/serial number; must be on database. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - JCN system generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E)

DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.252 End Item Repair of a SEGTE (No Removed Component) Figure 16-14 is an example of a VIDS/MAF documented when repairing an end item if no repairable components from an SEGTE are removed. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data to identify the SEGTE, always enter numeric one (1) for engine position in FSCM field; for

example, PDCA1: enter the failed part(s)/record supply requisition(s). A/T is 0, MAL Code is 000, and QTY is 00000 WORK UNIT CODE - Enter the specific WUC of the item being processed. TRANS - Must be 12. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number; must be on database. 16-40 COMNAVAIRFORINST 4790.2C 15 Jan 2017 W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC -

Enter appropriate job status, Julian dates and times. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.253 End Item Repair (Removed Repairable Component) Figure 16-15 is an example of a VIDS/MAF documented when repairing an end item that involved removal and replacement of a repairable component. A VIDS/MAF with a different JCN is required for each removed repairable component. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is

electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisitions(s). WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Must be 23. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number; must be on database. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time;

system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates the contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates the contract number JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the

MAF, based on the individuals SMQ. 16-41 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.254 Facilitate Other Maintenance (FOM) Action Figure 16-16 is an example of a FOM VIDS/MAF. A FOM action is the removal and reinstallation of an RFI component from the same end item in support of another maintenance action on the end item. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisitions(s). WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Must be 11. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Must be S. (Appendix E) MAL CODE - Must be 800 or 802 if corrosion related. (Appendix E) I/P - Enter

the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED

BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.255 Primary Work Center Repair Action When more than one work center works on the same maintenance action (Figures 16-17, 16-18, and 1619), one of them is designated the primary work center and the others are assisting work centers. Each work center participating in the maintenance action must generate a separate MAF with the same JCN. The primary work center describes the original method of discovery and accounts for the number of items processed. Assisting work centers document WD Code V If the assisting and the primary work centers work on the same work unit coded item, the assisting work center accounts for 0 items processed. If they work on different work unit coded items, the assisting work center accounts for its number of items processed. Refer to paragraph 16254 for

an example of FOM actions Figure 16-17 is an example of the VIDS/MAF documented for a repair action requiring an assisting work center. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisitions(s). WORK UNIT CODE - Enter the specific WUC of the item being processed. 16-42 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ACT ORG - System generated. TRANS - Must be 11 or 12. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Must be 800. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the

TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals

SMQ. 16.256 Assisting Work Centers (Same WUC) Figure 16-18 is an example of an assisting work center working on a same work coded item. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisitions(s). WORK UNIT CODE - Must be the same as the primary work centers MAF. ACT ORG - System generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Items processed must be 0. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System

generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. 16-43 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.257

Assisting Work Centers (Different WUC) Figure 16-19 is an example of an assisting work center working on a different work unit coded item. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisitions(s). WORK UNIT CODE - Must be the different than the primary work center. ACT ORG - System generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System

generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.258 On-Equipment

Cannibalization Cannibalization is the removal of an RFI item from one piece of equipment so that it may be used in a different piece of equipment. Cannibalization is controlled by Maintenance Control/Production Control, and should be authorized only when it appears that Supply cannot respond in time to avoid the curtailment of the operational commitment. The cancellation of a cannibalization JCN should occur only if no cannibalization action has been physically started. In the event that the actual removal for cannibalization action has been initiated/completed and the requirement is cancelled, reinstall the cannibalized item, documenting the action as if it were to FOM. Figure 16-20 is an example of cannibalization and subsequent replacement of a component from an end item and is documented on a VIDS/MAF in normal manner of a removed and replaced component. The following data fields require entries for a completed action. Some data fields are system generated or updated by using

on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - System generated. 16-44 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - System generated. (Appendix E) M/L - System generated. A/T - System generated. (Appendix E) MAL CODE - Enter the appropriate MAL Code; must be 812, 813, or 814. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the equipment. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Enter WD Code; must be O. (Appendix E) T/M - TM Code; must be B. (Appendix E) POSIT - Enter the appropriate PSI (if applicable) SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate

meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT

CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.259 Support Equipment (SE) Turned-In by a Supported Activity for Scheduled or Unscheduled Maintenance (Excluding PME) Figures 16-21 and 16-22 are examples of a turn-in VIDS/MAF from a supported activity requesting scheduled or unscheduled maintenance on a piece of SE. The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code SI ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - Not required. M/L* - System generated. A/T - Not required. MAL CODE - Not required. I/P - Not required. HOURS - Not required. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO*

- Enter the appropriate serial number. W/D* - Enter WD Code O. (Appendix E) T/M* - Enter the appropriate TM Code. (Appendix E) POSIT - Not required. SFTY/EI - Not required. 16-45 COMNAVAIRFORINST 4790.2C 15 Jan 2017 REPAIR CYCLE - Received date/time; system generated. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER* - Enter the JCN from the activity turning in the equipment. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. Enter the point of contact CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Not required. 16.2510 Turn-In Document Off-Equipment Repair Figure 16-23 is an example of the turn-in document to initiate an off-equipment repair of a removed component. A separate turn-in document with the same JCN as the removal MAF is

required for each removed component to be repaired. The following data fields are system generated Automated Aeronautical Material Screening Unit (AMSU) induction displays the following information: WORK UNIT CODE - System generated. ACT ORG - I-level Organization Code; system generated. TRANS - (Appendix E) M/L - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. (Optional) MAINTENANCE/SUPPLY REC - System generated. (Optional) REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. WORK CENTER - System generated. DISCREPANCY - System generated. CORRECTIVE ACTION - Applies

to auto BCM actions. CORRECTED BY/INSPECTED BY/SUPERVISOR - Applies to auto BCM actions. MAINT CONTROL - No entry allowed. 16.2511 Turn-In Document SEGTE Repair Figure 16-24 is an example of the turn-in document to initiate an off-equipment repair of SEGTE. The following data fields are system generated. Automated AMSU induction displays the following information: WORK UNIT CODE - System generated. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code. (Appendix E) M/L - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP - System generated. BU/SERNO - System generated. 16-46 COMNAVAIRFORINST 4790.2C 15 Jan 2017 W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system

generated. (Optional) MAINTENANCE/SUPPLY REC - System generated. (Optional) REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. WORK CENTER - System generated. DISCREPANCY - System generated. CORRECTIVE ACTION - Applies to auto BCM actions. CORRECTED BY/INSPECTED BY/SUPERVISOR - Applies to auto BCM actions. MAINT CONTROL - No entry allowed. 16.2512 Off-Equipment Component Repair Figure 16-25 is an example of a completed off-equipment component repair action documented by completing the turn-in MAF. This is the last MAF required if no repairable subassemblies are removed on the component. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields system generated from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate

data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE* - Enter the specific WUC of the item being processed. System generated ACT ORG* - I-level Organization Code. System generated TRANS - Must be 31or 32. (Appendix E) M/L* - Must be 2. System generated A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP* - Enter the TEC for the item being processed. System generated BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. System generated W/D* - Enter the appropriate WD Code. System generated (Appendix E) T/M* - Enter the appropriate TM Code. System generated (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). System generated SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the

appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM*-Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number System generated WORK CENTER* - Enter the appropriate Work Center Code. System generated (Appendix E) DISCREPANCY*- Enter the narrative description of the discrepancy. System generated CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2513 Suffix Turn-In Document Figure 16-26 is an example of the suffix VIDS/MAF turn-in document to initiate an off-equipment repair of a subassembly removed from a component. A separate turn-in document with a different suffix

of the JCN used for component removal is required for each removed subassembly. The following data fields are system generated. Automated AMSU Induction displays the following information: 16-47 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE - System generated. ACT ORG - I-level Organization Code. System generated TRANS - (Appendix E) M/L - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. MAINTENANCE/SUPPLY REC - System generated. REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. WORK CENTER - Blank. DISCREPANCY - System generated. CORRECTIVE ACTION -

Applies to auto BCM actions. CORRECTED BY/INSPECTED BY/SUPERVISOR - Applies to auto BCM actions. MAINT CONTROL - No entry allowed. 16.2514 Off-Equipment Subassembly Repair Figure 16-27 is an example of a completed off-equipment component repair action documented by completing the turn-in suffix VIDS/MAF. This is the last MAF required if no repairable subsubassemblies are removed from the subassembly The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions An asterisk (*) denotes those data fields from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE* - Enter the specific WUC of the item being processed. System generated ACT ORG* - I-level Organization Code. System

generated TRANS - Must be 31or 32. (Appendix E) M/L* - Must be 2. System generated A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. TYPE EQUIP* - Enter the TEC for the item being processed. System generated BU/SERNO* - Enter the appropriate bureau/serial number. System generated W/D* - Enter the appropriate WD Code. System generated (Appendix E) T/M* - Enter the appropriate TM Code. System generated (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). System generated SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third

time cycle indicates contract number System generated JOB CONTROL NUMBER* - JCN system generated. WORK CENTER* - Enter the appropriate Work Center Code. System generated (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. System generated CORRECTIVE ACTION - Enter the narrative description of the corrective action. 16-48 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: If repairable sub-assemblies are removed, repeat the procedures described in paragraphs 16.2513 and 162514 NALCOMIS will automatically assign a double suffix JCN as outlined in paragraph 16.1 16.2515 Inspection Control Document Figure 16-28 is an example of an inspection control document. Production Control will generate a control MAF for each look phase inspection. The control

document has a special JCN constructed per paragraph 16.1 and is used to accumulate the man-hours (NALCOMIS will track EMT) expended by the primary work center controlling the inspection. Control documents will account for 1 item processed If the primary work center performs the entire inspection, the control document is the only MAF required. If more than one work center is involved in the look phase, the control MAF will show 1 item processed and 0.0 man-hours and the supporting look phase MAF will show 0 items processed and accumulated manhours The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the total number of man-hours if combined with look phase. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - First three

positions must be 030. ACT ORG - I-level Organization Code. System generated TRANS - Must be 11. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - System generated. (Appendix E) MAL CODE - Must be 000. System generated (Appendix E) I/P - Must be 01. TYPE EQUIP - Enter the TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - System generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Not required. METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code (Appendix E). DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the

corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2516 Inspection Look Phase Supporting Document Figure 16-29 is an example of an inspection supporting document. Each assisting work center participating in the inspection will generate a look phase supporting MAF. NALCOMIS will provide the same JCN as the control MAF. Supporting documents are used to accumulate the man-hours expended by assisting work centers. Supporting documents will account for 0 items processed The following data fields require entries for a completed action. Some data fields are system generated or updated by using on-line functions. 16-49 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the total number of

man-hours if combined with look phase. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - First three positions must be 030. ACT ORG - I-level Organization Code. System generated TRANS - Must be 11. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - System generated. (Appendix E) MAL CODE - Must be 000. System generated (Appendix E) I/P - Must be 00. HOURS - System generated from accumulated work hours field. System generated TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - System generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Not required. METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates

and times. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2517 Inspection Fix Phase Document Figure 16-30 is an example of the fix document. Fix phase MAFs are used to document repair of discrepancies discovered during an inspection. A fix phase MAF has an alpha/numeric JCN (NALCOMIS auto assigns this JCN) constructed per paragraph 16.1 The WUC identifies the failed component/system The following data fields require entries for a completed action. Some data fields are system generated or updated by using on-line function. ENTRIES REQUIRED SIGNATURE - Check the

appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE -Enter the appropriate Malfunction Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). 16-50 COMNAVAIRFORINST 4790.2C

15 Jan 2017 REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted

to the MAF, based on the individuals SMQ. 16.2518 End Item TD Compliance (No Removal Component) Figure 16-31 is an example of a TD compliance VIDS/MAF documenting an end item TD with no removed component. For each component removed, a separate TD compliance turn-in document is generated. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. NOTE: TDs must reside in the configuration sub-system prior to the TD MAF being initiated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Trans Code 41. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Leave blank. I/P - Enter the total number of

items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Not required. T/M - Not required. POSIT - Not required. SFTY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data, if required. INSTALLED/NEW ITEM - Enter the appropriate data, if required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate work center. DISCREPANCY- Enter the narrative description of the discrepancy. System generated CORRECTIVE ACTION - Enter the narrative description. CORRECTED BY/INSPECTED

BY/SUPERVISOR - Signatures are electronically posted to the MAF. MAINT CONTROL - Signature is electronically posted to the MAF. Not required 16-51 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2519 TD Compliance Supporting VIDS/MAF Figure 16-32 is an example of a TD compliance supporting VIDS/MAF; note the TD compliance is not identified. The following data fields require entries or are of special interest Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Transaction Code 11. (Appendix E) M/L - Must be 1. A/T - AT Code must be S. (Appendix E) MAL CODE - MAL Code; must be 804. (Appendix E) I/P - Enter the total number of items processed. HOURS -

System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC. The TEC entered on the TD compliance facilitate MAF will be a G, H, M, S or V series code that identifies the end item the component was removed from. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD Code; must be O. (Appendix E) T/M - TM Code, must be B. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Not required. TECHNICAL DIRECTIVE ID - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date/time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Not required. INSTALLED NEW/ITEM - Not required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate work center. DISCREPANCY- Enter the narrative description. CORRECTIVE ACTION - Enter the narrative description.

CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF. MAINT CONTROL - Signature is electronically posted to the MAF. Not required 16.2520 TD Compliance Turn-In Document Figure 16-33 is an example of a TD compliance turn-in document to initiate off-equipment compliance with a TD. The TD compliance turn-in document is a MAF with the same JCN as the component removal document. For component TD compliance actions on supply stock, the TD compliance turn-in document will be generated by the Supply Department, NALCOMIS will auto-assign a supply JCN, no removal document is required. The following data fields require entries or are system generated/updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Enter Transaction Code 47. (Appendix E) M/L - Enter

the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Not required. 16-52 COMNAVAIRFORINST 4790.2C 15 Jan 2017 I/P - Not required. HOURS - Not required. EMT - Not required. TYPE EQUIP - Enter the TEC. The TEC must be a Y series code for a component TD compliance BU/SERNO - Enter the appropriate component serial number or 000000 if nonserialized. W/D - Not required. T/M - Not required. POSIT - Not required. SFTY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received Date/Time; system generated. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Enter the appropriate data as required. INSTALLED/NEW ITEM - Not required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code (Appendix E) DISCREPANCY - Enter the narrative description. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED

BY/SUPERVISOR - Not required. MAINT CONTROL - Not required. 16.2521 Off-Equipment TD Compliance Action Figure 16-34 is an example of a completed off-equipment TD compliance action. Off-equipment TD compliance actions are documented by completing the TD compliance turn-in document. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Transaction code must be 47. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate technical directive code. (Appendix E) MAL CODE - Leave blank. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work

hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Not required. T/M - Not required. POSIT - PSI (if applicable). SFTY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date/time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates/times. REMOVED/OLD ITEM - Enter the appropriate data, if required. INSTALLED NEW/ITEM - Enter the appropriate data, if required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description. CORRECTIVE ACTION - Enter the narrative description. 16-53 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are

electronically posted to the MAF. MAINT CONTROL - Signature is electronically posted to the MAF. Not required 16.2522 TD Compliance Removal (On-Equipment) Figure 16-35 is an example of a completed on-equipment TD compliance removal which is documented in the same manner as TD incorporations except for data field action taken. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using online functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Transaction Code must be 41. (Appendix E) M/L - Must be 1. A/T - Technical Directive Status Code must be Q. (Appendix E) MAL CODE - Leave blank. I/P - Enter the total number of items processed. HOURS -

System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Not required. T/M - Not required. POSIT - PSI (if applicable). SFTY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date/time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates/times. REMOVED/OLD ITEM - Not required. INSTALLED NEW/ITEM - Not required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description. CORRECTIVE ACTION - Enter the narrative description. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF. MAINT CONTROL - Signature is

electronically posted to the MAF. Not required 16.2523 Inventory Transaction (Gain) Figure 16-40 is an example of a VIDS/MAF documented when reporting an equipment gain. The following data fields are system generated or updated by using on-line functions: ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. WORK UNIT CODE - Not required. ACT ORG - System generated. TRANS - Transaction Code; system generated. M/L - Not required. A/T - Not required. MAL CODE - Not required. I/P - Not required. TYPE EQUIP - Enter the appropriate TEC. 16-54 COMNAVAIRFORINST 4790.2C 15 Jan 2017 BU/SERNO - Enter the serial number of the item being processed. The serial number is always six characters and not zeros. If there are fewer than six characters, prefix the number with zeros until there are six. If there are more than six characters, enter only the last six If there is no serial number (due to missing name plates, etc.) create a serial number by using

the Organization Code of the reporting custodian plus a unique, locally assigned three character serial, such as A9D001 or A9DAAT. This assigned serial number is to be affixed to the equipment and will remain with the unit until the equipment is stricken from naval inventory. W/D - Not required. T/M - Not required. METER - Enter the appropriate meter time in whole hours (no tenths) or cycle/starts from the equipment meter. Prefix with enough zeros and the letter M or S to make a total of five positions, such as M0921 If the equipment has no meter, enter A0000. INV CD - Enter the appropriate Inventory Code. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Not required. WORK CENTER - Not required. DISCREPANCY - Not required. CORRECTIVE ACTION - System generated. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. SUPERVISOR - Name of

person performing. MAINT CONTROL - Not required. 16.2524 Inventory Transaction (Loss) Figure 16-41 is an example of a VIDS/MAF documented when reporting an equipment loss. The following data fields are system generated or updated by using on-line functions: WORK UNIT CODE - Not required. ACT ORG - Enter the appropriate Organization Code. TRANS - Transaction code; system generated. M/L - Not required. A/T - Not required. MAL CODE - Not required. I/P - Not required. TYPE EQUIP - Enter the appropriate TEC. First position must be D, G, H, M, S, V, or Y BU/SERNO - Enter the serial number of the item being processed. Refer to paragraph 162523 W/D - Not required. T/M - Not required. METER - Enter the appropriate meter time in whole hours (no tenths) or cycle/starts from the equipment meter. Prefix with enough zeros and the letter M or S to make a total of five positions, such as M0921 If the equipment has no meter, enter A0000. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE -

Received date/time; system generated. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Not required. WORK CENTER - Not required. DISCREPANCY - Not required. CORRECTIVE ACTION - System generated. CORRECTED BY/INSPECTED BY/SUPERVISOR - System generated. MAINT CONTROL - Not required. 16-55 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2525 Removed Component for Calibration Figure 16-42 is an example of a VIDS/MAF documenting the removal of a component for processing to the PME work center on a METER Card. If informed that the component failed, the Transaction Code data field will be 23; Action Taken Code will be R and the REMOVED/OLD ITEM and the INSTALLED/NEW ITEM fields will be filled in. Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED

WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG* - I-level Organization Code. TRANS - Must be 11. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed; first position must be D, G, H, M, S, V, or Y. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the

appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number System generated JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2526 Component Turn-In Document Figure 16-43 is an example of a turn-in document to initiate repair of a removed component being received from an external activity. A separate turn-in document with the same JCN as the

removal MAF is required for each removed component to be repaired. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code "D" WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Not required, unless item is an auto BCM action. M/L* - Must be 2. A/T - Not required, unless item is an auto BCM action. MAL CODE - Not required, unless item is an auto BCM action. I/P - Not required, unless item is an auto BCM action. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. W/D* - Enter the appropriate WD Code. (Appendix E) 16-56 COMNAVAIRFORINST 4790.2C 15 Jan 2017 T/M* - Enter the appropriate TM Code. (Appendix E) POSIT* - Enter the appropriate PSI; if applicable. SFTY/EI* - Enter the appropriate safety/EI number; if applicable. REPAIR CYCLE* - System generated, may be updated upon

induction. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) Auto assigned if on the ICRL. DISCREPANCY* - Enter the narrative description of the discrepancy. TURN-IN DOCUMENT* - Enter the appropriate requisition number for the replacement component. CORRECTIVE ACTION* - Not required, unless item is an auto BCM action. CORRECTED BY/INSPECTED BY/SUPERVISOR* - Not required, unless item is an auto BCM action. 16.2527 BCM Action (AMSU) Figure 16-44 is an example of a BCM action at AMSU. ASD will retain a MAF as a suspense copy, and the component will be forwarded to the IMA screening unit. The AMSU performs administrative screening of the component to determine if a check/test/repair capability exists in the IMA work centers. If it does

not, the AMSU completes the MAF in the following manner. (*) denotes those data fields completed by the AMSU induction. Type MAF Code "D" AMSU and work centers will not document any man-hours on BCM 1 MAFs. WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS* - Must be 31. M/L* - Must be 2. A/T* - Must be 1 or 8. MAL CODE* - Enter the appropriate MAL Code. (Appendix E) I/P* - Must be 1. HOURS* - System generated from accumulated work hours field. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. W/D* - Enter the appropriate WD Code. (Appendix E) T/M* - Enter the appropriate TM Code. (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE* - System generated, may be updated upon induction. REMOVED/OLD ITEM* - Enter the

appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate Work Center Code 05A. Auto assigned if on the ICRL (Appendix E). DISCREPANCY* - Enter the narrative description of the discrepancy. TURN-IN DOCUMENT - Enter the appropriate requisition number for the replacement component. CORRECTIVE ACTION* - System generated. CORRECTED BY/INSPECTED BY/SUPERVISOR* - Signature is electronically posted to the MAF, based on the individual PASSWORD/SMQ. NALCOMIS will create the appropriate mailbox messages as required. MAINT CONTROL - Signature electronically posted to the MAF, based on the individuals SMQ. 16.2528 Troubleshooting Close Out Figure 16-45 is an example of a VIDS/MAF documented for the reporting of man-hours expended in troubleshooting. NALCOMIS must create the close-out MAF automatically by performing

the basic MAF update function and indicating the close-out to be performed. The following explains documentation: 16-57 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - System generated. WORK UNIT CODE - Same as original MAF. System generated ACT ORG - I-level organization code. System generated TRANS - System generated. M/L - System generated. A/T - System generated. MAL CODE - System generated. I/P - System generated. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. METER - System generated. REPAIR CYCLE - System generated. MAINTENANCE/SUPPLY REC - System generated. JOB CONTROL NUMBER - Same as original MAF. System generated WORK CENTER - System generated. DISCREPANCY - System generated. CORRECTIVE ACTION - System generated.

CORRECTED BY/INSPECTED BY/SUPERVISOR - System generated as required. 16.2529 Assisting Work Center (Same WUC) Figure 16-46 is an example of an assisting work center working on a same work unit coded item. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - Must be the same as the primary work centers MAF. ACT ORG - System generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Items processed must be 0. HOURS - System generated from accumulated work hours field. EMT

- System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. 16-58 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is

electronically posted to the MAF, based on the individuals SMQ. 16.2530 Assisting Work Center (Different WUC) Figure 16-47 is an example of an assisting work center working on a different work unit coded item. For NDI actions done on assist MAF refer to paragraphs 16.2547 and 162548 for action taken and MAL code. The transaction code will be 11 for NDI assists Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - Must be different from the primary Work Center Code. (Appendix E) ACT ORG - System generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix

E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF,

based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2531 Component Repaired Using a Repairable Subassembly Figure 16-48 is an example of removal, replacement, and subsequent repair actions on subassemblies/modules of a major component. When a defective subassembly/module is removed from a major component undergoing repair in the IMA, and the repair of these items is accomplished as a separate job, NALCOMIS will generate a proper sequenced suffix JCN after the requested parts are approved. The failed/required material field is used to document the repair of the major component Enter the following information for each subassembly/module removed. Complete the remainder of the MAF as specified in paragraph 16.213 The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. (*) denotes those data fields completed by the

AMSU induction. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. 16-59 COMNAVAIRFORINST 4790.2C 15 Jan 2017 FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). Upon approval of the requested subassemblies/modules by Production Control, NALCOMIS will auto assign a DDSN to each failed/required line of the MAF. WORK UNIT CODE - Enter the specific WUC of the unit being processed. ACT ORG - I-level Organization Code. TRANS - Must be 31or 32. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial W/D* - Enter the appropriate WD Code. (Appendix E) T/M* -

Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE* - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC* - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate removed/old item data. JOB CONTROL NUMBER* - Enter the appropriate JCN. WORK CENTER* - If the CAGE/part number is on the database ICRL, the work center will be electronically posted to the turn-in MAF for each repairable. If CAGE/part number is not on the ICRL, enter the appropriate work center code. (Appendix E) DISCREPANCY* - Enter the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is

electronically posted to the MAF, based on the individuals SMQ. 16.2532 Subassembly/Module Repair (Suffix) Figure 16-49 is an example of a subassembly repair action documented by completing the suffix MAF. This is the last MAF required if no repairable subassemblies are removed from the subassembly. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). Upon approval of the requested subassemblies/modules by Production Control, NALCOMIS will auto assign a DDSN to each failed/required line of the MAF. WORK UNIT CODE - System generated. ACT ORG - I-level Organization Code. TRANS - Must be 31 or 32. (Appendix E) M/L - System generated; must be 2. A/T - Enter

the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. 16-60 COMNAVAIRFORINST 4790.2C 15 Jan 2017 T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated. WORK CENTER - If the FSCM/part number is on the database ICRL, the work center will be electronically posted to the turn-in MAF for each repairable. If FSCM/part number is not on the ICRL, enter the appropriate Work Center Code. (Appendix E)

DISCREPANCY - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2533 Sub-Subassembly/Module Repair (Double Suffix) Figure 16-50 is an example of a sub-subassembly repair action documented by completing the double suffix MAF. The failed/required material field is used to document the repair of the sub-subassembly Enter information for those items, which are known or suspected to have contributed to the discrepancy. NALCOMIS will generate the proper sequenced double suffix JCN. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using online functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted.

ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). Upon approval of the requested sub-subassemblies/modules by Production Control NALCOMIS will auto assign a DDSN to each failed/required line of the MAF. WORK UNIT CODE - System generated. ACT ORG - I-level Organization Code. TRANS - Must be 31 or 32. (Appendix E) M/L - System generated; must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the

appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. WORK CENTER - If the FSCM/part number is on the database ICRL, the work center will be electronically posted to the turn-in MAF for each repairable. If FSCM/part number is not on the ICRL, enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action. 16-61 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2534 Cannibalization (End Item) Figure 16-51 is an example of a cannibalization of an end item. The removal of items for cannibalization will be documented on a MAF using the

appropriate function and procedures listed in paragraph 16.213 The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level organization code. System generated TRANS - System generated. (Appendix E) M/L - System generated. A/T - System generated. (Appendix E) MAL CODE - Enter the appropriate MAL code; must be 812, 813, 814, 815, 816, 817, or 818 (Appendix E). I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the equipment. BU/SERNO - Enter the appropriate

bureau/serial number; must be on the database. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the

discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2535 Cannibalization (From AWP Component) Figure 16-52 is an example of cannibalization from an AWP component. If a joint decision is made by supply and IMA to cannibalize instead of placing the repairable component AWP, the following information will be entered in the FAILED/REQUIRED MATERIAL fields on the MAF from which the serviceable repairable/consumable item is removed. NALCOMIS performs this function automatically The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. 16-62 COMNAVAIRFORINST 4790.2C 15 Jan 2017 NOTE: By performing these functions within NALCOMIS the

fields identified below as "Not required" will be completed as the MAF sign-off occurs. ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - System generated. WORK UNIT CODE - Not required. ACT ORG - Not required. TRANS - Not required. M/L - Not required. A/T - System generated. MAL CODE - System generated. I/P - Not required. HOURS - Not required. EMT - Not required. TYPE EQUIP - Not required. BU/SERNO - Not required. W/D - Not required. T/M - Not required. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Not required. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Not required. WORK CENTER - Not required. DISCREPANCY - Not required. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. MAINT CONTROL - Not required. 16.2536 Cannibalization (Off-Equipment) Figure 16-53 is an example of cannibalization of an item from a repairable

component or subassembly that is documented in the FAILED/REQUIRED MATERIAL section of the MAF for the component/subassembly from which the item was cannibalized. The removed item is considered to have caused AWP but is not a "failed part" of the component/subassembly from which it was cannibalized. It may be a failed part of the component for which it was cannibalized. Identify the removed item in the normal manner of a required part that caused AWP and transfer the requisition to this JCN. NALCOMIS performs this function automatically. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions NOTE: By performing these functions within NALCOMIS the fields identified below as "Not required" will be completed as the MAF sign-off occurs. ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Indicate (as appropriate) the

FP and AWP blocks and fill in the AT and MAL blocks (as required), QTY (as required), PROJ and PRI (as appropriate), Julian date ordered and REQ NO (as applicable). System generated WORK UNIT CODE - Not required. ACT ORG - Not required. TRANS - Not required. M/L - Not required. A/T - System generated. MAL CODE - System generated. I/P - Not required. 16-63 COMNAVAIRFORINST 4790.2C 15 Jan 2017 HOURS - Not required. EMT - Not required. TYPE EQUIP - Not required. BU/SERNO - Not required. W/D - Not required. T/M - Not required. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Not required. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Not required. WORK CENTER - Not required. DISCREPANCY - Not required. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. MAINT CONTROL - Not required. 16.2537 Matched Set (Repair and No Repair) Figures 16-54 and 16-55 are examples of a VIDS/MAF documented when

processing a matched set. Figure 16-54 illustrates repair action and Figure 16-55 illustrates no repair action. When the "no defect" component is determined at the I-level activity, it must be documented per paragraph 16.213 with the following exceptions: Action Taken Code must be A, MAL Description Code must be 806. Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code D ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed part(s), and/or record supply requisition(s). WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code. TRANS - Must be 31or 32. (Appendix E) M/L* - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix

E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number, must be on database. W/D* - Enter the appropriate WD code. (Appendix E) T/M* - Enter the appropriate TM code. (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate removed/old item data. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Enter the assigned JCN. WORK CENTER* - Enter the appropriate work center code, auto assigned if FSCM/part number

is on database ICRL. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. 16-64 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2538 Tire and Wheel Documentation (Tires Prepositioned in W/C and Ordering Replacement Tire) Figures 16-56 and 16-57 are examples of the VIDS/MAF documented for aircraft tire and wheel actions. The work center must document tire identification and BCM data in the failed and required material fields of the MAF. Using AMSU Receipt, and various on-line functions the following data fields require entry An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code D ENTRIES REQUIRED SIGNATURE - Check the appropriate field,

signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data (as required). WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG - I-level organization code. System generated TRANS - Must be 31or 32. (Appendix E) I/P* - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - Not required. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number, must be on database. W/D* - Enter the appropriate WD code. (Appendix E) T/M* - Enter the appropriate TM code. (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). METER - Not required. REPAIR CYCLE* - System generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian

dates and times. REMOVED/OLD ITEM* - Enter the appropriate removed/old item data. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Not required. JOB CONTROL NUMBER* - Assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate work center code. Auto assigned if FSCM/part number is on database ICRL. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION* - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2539 Transferring IMA Close Out (Post/Predeployment) Figure 16-58 is an example of an IMA close out for post/predeployment. The following data fields require entries to document a completed action. Some data fields are system

generated or updated by using online functions (*) denotes those data fields from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter for each "missing" FLR module, subassembly of subsubassembly (as appropriate). The action taken field must be P WORK UNIT CODE - Enter the specific WUC of the item being processed. 16-65 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ACT ORG - I-level Organization Code. TRANS - Must be 31 or 32. (Appendix E) M/L - Must be 2. A/T - Must be D. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter

the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate removed/old item data. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ.

16.2540 Receiving IMA (Reinitiation Documentation) Figure 16-59 is an example of a reinitiated VIDS/MAF from a transferring I-level activity. On receipt of a repairable item from another I-level activity, the receiving AMSU will forward a copy of the MAF to the local Supply CCS. Subsequent repair and disposition will be documented on the new MAF per paragraph 16.213, except the Received Date field will reflect the date the component was received from the transferring I-level activity. The following data fields require entries An asterisk (*) denotes those data fields completed by the AMSU induction using information taken from the transferring activity MAF. Type MAF Code D. WORK UNIT CODE* - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code. M/L - Must be 2. EMT - System generated. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - Enter the appropriate WD Code. (Appendix E)

T/M* - Enter the appropriate TM Code. (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE* - Received date/time; system generated. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Enter the appropriate JCN from the activity item is received from. WORK CENTER* - Enter the appropriate work center code, auto assigned if FSCM/part number is on database ICRL. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. TURN IN DDSN* - Enter the turn-in document from the activity item is being received from. PILOT/INITIATOR* - Enter the person’s name (as appropriate). 16-66 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2541 Component Missing SRC Card Figure 16-60 is an example of a VIDS/MAF documented for turn-in of a component that is

missing the SRC card. Using AMSU receipt, the following data fields require entry An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code D WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code, system generated. TRANS - Required if item is an auto BCM action. M/L* - Must be 2. A/T - Required if item is an auto BCM action. MAL CODE* - Enter "140". I/P - Required if item is an auto BCM action. TYPE EQUIP* - Enter the TEC for the item being processed. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - Enter the appropriate WD Code. (Appendix E) T/M* - Enter the appropriate TM Code. (Appendix E) POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE* - System generated, may be updated upon induction. MAINTENANCE/SUPPLY REC* - Not required. REMOVED/OLD ITEM* - Enter the appropriate removed/old item data. Time

cycle field enter the appropriate time/cycle prefix code (Appendix E) followed by 9999. The use of 9999 indicates the value is unknown. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate work center code. Auto assigned if on the ICRL (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. TURN-IN DOCUMENT* - Enter the appropriate requisition number for the replacement component. CORRECTIVE ACTION* - Required if item is an auto BCM action. CORRECTED BY/INSPECTED BY/SUPERVISOR* - Required if item is an auto BCM action. 16.2542 Corrosion Supporting MAF Figure 16-61 is an example of a supporting MAF documenting corrosion treatment. If corrosion caused the malfunction and treatment of that condition results in elimination of the discrepancy, then it is proper to use Transaction Code 31 or 32 with an AT Code C and MAL Codes C01 through C33. The only time a supporting MAF (Z/C01 through C33/Transaction Code

11) is required is when the corrosion treatment is separate and distinct from the malfunction cause. The following explains documentation: ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code. System generated TRANS - Enter the appropriate Transaction Code, as required. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - System generated. T/M - System generated.

POSIT - Enter the appropriate PSI (if applicable). 16-67 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SFTY/EI - Enter the appropriate safety/EI number (if applicable). METER - Not required for level 2 maintenance. REPAIR CYCLE - System generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate work center code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2543 Turn-In from Supply for TD Compliance Figure 16-62 is an example of the VIDS/MAF

documented for an end item turned in from a supply activity for TD compliance. The supply activity, after coordinating through the I-level QA, must initiate a TD compliance MAF for each item requiring TD compliance. The supply activity must complete the following data fields on the TD compliance MAF prior to issuing to Production Control for scheduling. The following explains documentation: TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. TYPE EQUIP - Enter the TEC for the equipment. BU/SERNO - Enter the appropriate bureau/serial number. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if

applicable). REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates control number JOB CONTROL NUMBER - System will generate Supply ORG JCN. DISCREPANCY - Enter the narrative description of the discrepancy and initiator. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD for supply induction of items requiring TD compliance. 16.2544 VIDS/MAF Work Request (Production Control Entries) Figure 16-63 is an example of Work Request VIDS/MAF data fields completed by Production Control. This information is provided by the requesting activity. Using the appropriate on-line function, enter the required data. The following explains documentation: TYPE MAF CODE - "WR". ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE - Enter the

specific WUC of the item being processed. ACT ORG - System generated. TRANS - Not required. M/L - Must be 2. A/T - Not required. MAL CODE - Not required. 16-68 COMNAVAIRFORINST 4790.2C 15 Jan 2017 I/P - Not required. HOURS - Not required. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number, must be on database. W/D - Enter the appropriate WD code. (Appendix E) T/M - Enter the appropriate TM code. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. May be modified prior to approval MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate Work Center Code; auto assigned if FSCM/part

number is on database ICRL. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. PILOT/INITIATOR - Signature is electronically posted to the MAF upon approval. MAINT CONTROL - Not required. 16.2545 VIDS/MAF Work Request (Local Manufacture/Fabrication) Figure 16-64 is an example of a completed Work Request VIDS/MAF documenting local manufacture or fabrication. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data as required. WORK UNIT CODE - System generated. ACT ORG - System generated. TRANS - Transaction Code must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be A. (Appendix E) MAL CODE - MAL code,

must be 000. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. WORK CENTER - System generated. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - System generated. 16-69 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAINT

CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2546 VIDS/MAF Work Request (Supply Asset Build-Up Induction) Figure 16-65 is an example of a completed Work Request VIDS/MAF documenting supply asset build-up inductions. Supply must move the item to suspense prior to performing the Work Request function The following data fields require entries. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - System generated. ACT ORG - System generated. TRANS - System generated. M/L - Must be 2. A/T - AT Code must be A. (Appendix E) MAL CODE - MAL code, must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System

generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the serial number requiring build-up. W/D - Enter W/D Code O. T/M - Enter T/M Code T. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - System generated upon initiation. WORK CENTER - Enter the appropriate work center. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - System generated. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2547 Scheduled Maintenance Work

Request (NDI In-Shop) (Passed Inspection) Figure 16-66 is an example of a completed Work Request VIDS/MAF documenting an In-Shop NDI. The following data fields require entries. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - System generated; must be 30.(Appendix E) M/L - Must be 2. A/T - AT code must be A. (Appendix E) MAL CODE - MAL code, must be 57 series. (Appendix E) I/P - Enter the total number of items being processed. 16-70 COMNAVAIRFORINST 4790.2C 15 Jan 2017 HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial

number. W/D - WD code must be O. (Appendix E) T/M - TM code (as appropriate). (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate work center. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2548 Scheduled Maintenance Work Request (NDI

On-Site) (Passed Inspection) Figure 16-67 is an example of a completed Work Request VIDS/MAF documenting an On-Site NDI Inspection. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - System generated; must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be A. (Appendix E) MAL CODE - MAL code, must be 57 series. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD code must be O. (Appendix E) T/M -

TM code (as appropriate). (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16-71 COMNAVAIRFORINST 4790.2C 15 Jan 2017 NOTE: The NDI technician shall sign-off the

squadron’s work request. Squadron Maintenance Control shall obtain the Level II copy within 48 hours. 16.2549 Scheduled Maintenance Work Request (NDI On-Site) (Failed Inspection) Figure 16-68 is an example of a completed Work Request VIDS/MAF documenting an On-Site NDI failing test. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - System generated; must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be F. (Appendix E) MAL CODE - MAL code, must be 57 series. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT -

System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD code must be O. (Appendix E) T/M - TM code (as appropriate). (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Not required. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate work center. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the

MAF, based on the individuals SMQ. 16.2550 Scheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) Figure 16-69 is an example of a completed Work Request VIDS/MAF documenting an In-Shop NDI failing test. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - System generated; must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be F. (Appendix E) MAL CODE - MAL code, must be 57 series. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. 16-72 COMNAVAIRFORINST 4790.2C 15 Jan 2017 EMT - System generated. TYPE

EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number, must be on database. W/D - WD Code must be O. (Appendix E) T/M - TM Code (as appropriate). (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate Work Center Code. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is

electronically posted to the MAF, based on the individuals SMQ. 16.2551 Unscheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) Figure 16-70 is an example of a completed Work Request VIDS/MAF documenting an In-Shop unscheduled NDI. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - Transaction code must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be A. (Appendix E) MAL CODE - MAL code must be 571. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the

appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number, must be on database. W/D - WD Code must be O. (Appendix E) T/M - TM Code must be S. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate Work Center Code. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF,

based on the individuals SMQ. 16-73 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2552 Unscheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) Figure 16-71 is an example of a completed Work Request VIDS/MAF documenting an In-Shop unscheduled NDI failing test. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - Transaction Code must be 30. (Appendix E) M/L - Must be 2. A/T - AT code must be F. (Appendix E) MAL CODE - MAL code must be 57 series. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated.

TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD code. (Appendix E) T/M - TM code. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the assigned JCN from the requesting activity. WORK CENTER - Enter the appropriate Work Center Code. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the

individuals SMQ. 16.2553 O-Level Armament Equipment Turn-In for Scheduled Maintenance Figure 16-72 is an example of an O-level armament equipment turn-in for scheduled maintenance. The following data fields require entries. Some data fields are system generated or updated by using on-line functions. (*) denotes those data fields completed by the AMSU induction. Type MAF Code "SD" ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Not required. M/L* - Must be 2. A/T - Not required. MAL CODE - Not required. I/P - Not required. HOURS - Not required. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. 16-74 COMNAVAIRFORINST 4790.2C 15 Jan 2017 BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not

required. SFTY/EI - Not required. REPAIR CYCLE* - Received date/time; system generated. MAINTENANCE/SUPPLY REC* - System generated. REMOVED/OLD ITEM* - Enter the appropriate data. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate Work Center Code, auto assigned if on database ICRL. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Not required. 16.2554 O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (No Material Required) (Completed) Figure 16-73 is an example of a completed VIDS/MAF documenting scheduled maintenance of a removed armament equipment pool item, no discrepancies. The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes

those data fields completed by the AMSU induction. Type MAF Code SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - Transaction code must be 31. (Appendix E) M/L* - Must be 2. A/T - AT Code must be A. (Appendix E) MAL CODE - MAL code must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number, must be on database. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter

the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate work center, auto assigned if on database ICRL. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16-75 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2555 O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (Maintenance and Material Required) (Completed) Figure 16-74 is an example of a completed VIDS/MAF documenting

scheduled maintenance of a removed armament equipment pool item; maintenance and material required. The following data fields require entries. Some data fields are system generated or updated by using on-line functions An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG* - System generated. TRANS - Transaction Code must be 32. (Appendix E) M/L* - Must be 2. A/T - AT Code must be C. (Appendix E) MAL CODE - MAL Code must be 804. (Appendix E) I/P - Items processed; must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC for the item being processed. BU/SERNO* - Enter the appropriate

bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. WORK CENTER* - System generated. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - System generated. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2556 Turn-In Acceptance/Functional Check on Armament Equipment Figure 16-75 is an example of a turn-in Work Request VIDS/MAF

documenting the acceptance/functional check on armament equipment received from another AEP or excess from a supported activity. The following data fields require entries. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - System generated. M/L - Must be 2. A/T - Not required. MAL CODE - Not required. I/P - Not required. 16-76 COMNAVAIRFORINST 4790.2C 15 Jan 2017 HOURS - Not required. EMT - Not required. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD Code must be O. (Appendix E) T/M - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date

and time. MAINTENANCE/SUPPLY REC - Not required. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the JCN from the activity turning in the component. WORK CENTER - Enter the appropriate Work Center Code. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. PILOT/INITIATOR - Enter the name of the person (as appropriate). MAINT CONTROL - Not required. 16.2557 Turn-In Acceptance/Functional Check on Armament Equipment (Completed) Figure 16-76 is an example of a Work Request Turn-In VIDS/MAF documenting the acceptance/functional check on armament equipment received from another armament equipment pool (AEP) or excess from a supported activity. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED

WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE - Enter the specific WUC of the item being inducted. ACT ORG - System generated. TRANS - System generated, must be 30. (Appendix E) M/L - Must be 2. A/T - AT Code must be A. (Appendix E) MAL CODE - MAL code (as appropriate). (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD Code. (Appendix E) T/M - TM Code. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data. JOB CONTROL NUMBER - Enter the assigned JCN

from the requesting/supported activity. WORK CENTER - Enter the appropriate Work Center Code. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR - Enter the name of the person (as appropriate). 16-77 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2558 Armament Equipment Pool Preservation/Depreservation Control Document (Completed) Figure 16-77 is a preservation/depreservation control document. Production Control will generate a MAF for each preservation/depreservation. The following data fields require entries Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is

electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed parts/record supply requisitions. WORK UNIT CODE - The first three positions must be 049. ACT ORG - System generated. TRANS - Transaction code must be 11. (Appendix E) M/L - Enter the appropriate maintenance level. A/T - AT Code must be 0. (Appendix E) MAL CODE - MAL Code must be 000. (Appendix E) I/P - Must be 01. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the appropriate TEC. BU/SERNO - Enter the appropriate bureau/serial number. W/D - WD Code must be O. (Appendix E) T/M - TM Code must be D. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Not required. METER - Enter the appropriate meter time (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate

job status, Julian dates and times. JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate work center. (Appendix E) WORK PRIORITY - Enter the appropriate work priority. SYSTEM REASON - Enter the short narrative description of the discrepancy. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2559 I-Level Armament Equipment Pool Component Due for Scheduled Maintenance (Completed) Figure 16-78 is an example of a completed VIDS/MAF documenting scheduled maintenance of an I-level AEP component. The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields

completed by the AMSU induction. Type MAF SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Transaction Code must be 31. (Appendix E) M/L* - Must be 2. A/T - AT Code must be A. (Appendix E) 16-78 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAL CODE - MAL Code must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time;

enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data. JOB CONTROL NUMBER* - Enter the assigned JCN from the IMA activity. WORK CENTER* - Enter the appropriate work center. Auto assigned if on the database ICRL DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2560 O-Level ALSS Equipment Due for Scheduled Maintenance (Maintenance and Material Required) (Completed) Figure 16-79 is an example of a completed VIDS/MAF documenting scheduled maintenance of ALSS equipment (maintenance and material

required). The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Transaction Code must be 32. (Appendix E) M/L* - Must be 2. A/T - AT Code must be C. (Appendix E) MAL CODE - MAL Code must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E)

POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data, as required. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - System generated. DISCREPANCY* - Enter the narrative description of the discrepancy. 16-79 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - System generated. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2561 O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Completed) Figure 16-80 is an example of a completed

VIDS/MAF documenting scheduled maintenance of ALSS personal equipment. The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Transaction Code must be 31. (Appendix E) M/L* - Must be 2. A/T - AT Code must be A. (Appendix E) MAL CODE - MAL Code must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be

O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data, as required. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate work center; auto assigned if FSCM/part number is on database ICRL. DISCREPANCY* - System generated. CORRECTIVE ACTION - System generated. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2562 O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Maintenance and

Material Required) (Completed) Figure 16-81 is an example of a completed VIDS/MAF documenting scheduled maintenance of ALSS personal equipment (maintenance and material required). The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. 16-80 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Transaction Code must be 32. (Appendix E) M/L* - Must be 2. A/T - AT Code must be C. (Appendix E) MAL CODE - MAL Code must be 804. (Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work

hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data, as required. JOB CONTROL NUMBER* - Enter the assigned JCN from the requesting activity. WORK CENTER* - Enter the appropriate Work Center Code; auto assigned if FSCM/part number is on database ICRL. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR*

- Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2563 I-Level ALSS Pool Component Due for Scheduled Maintenance (Completed) Figure 16-82 is an example of an I-level completed VIDS/MAF documenting scheduled maintenance of an ALSS pool component. The following data fields require entries Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF SD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data, as required. WORK UNIT CODE* - Enter the specific WUC of the item being inducted. ACT ORG* - System generated. TRANS - Transaction Code must be 31. (Appendix E) M/L* - Must be 2. A/T - AT Code must be A. (Appendix E) MAL CODE - MAL Code must be 804.

(Appendix E) I/P - Enter the total number of items being processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. (Appendix E) T/M* - TM Code must be D. (Appendix E) POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. 16-81 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data, as required. JOB CONTROL NUMBER* - Enter the assigned JCN of the IMA. WORK CENTER* - Enter the appropriate Work Center Code (Appendix E); auto assigned if FSCM/part number is on database ICRL. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the

corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - Enter the name of the person (as appropriate). MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2564 MAF Discrepancy (Supply Asset Induction Document) (Material Condition Tag Missing) Figure 16-83 is an example of a VIDS/MAF documented for items inducted from a supply activity for check, test, or service. Supply must move the item to suspense prior to performing the MAF function The following data fields require entries. Some data fields are system generated or updated by using online functions An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code D. ENTRIES REQUIRED SIGNATURE - Not required. ACCUMULATED WORK HOURS - Not required. FAILED/REQUIRED MATERIAL - Not required. WORK UNIT CODE* - Enter the appropriate WUC of item being inducted. ACT

ORG* - System generated. TRANS - Not required. M/L* - Must be 2. A/T - Not required. MAL CODE - Not required. I/P - Not required. HOURS - Not required. EMT - System generated. TYPE EQUIP* - Enter the appropriate TEC. BU/SERNO* - Enter the appropriate bureau/serial number. W/D* - WD Code must be O. T/M* - TM Code must be T. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC* - System generated. REMOVED/OLD ITEM - Enter the FSCM, part number, removed date, serial number of the removed item(s) and time cycle. If there is no serial number enter 0 JOB CONTROL NUMBER* - JCN will have a Supply Org code. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Not required. CORRECTED BY/INSPECTED BY/SUPERVISOR - Not required. PILOT/INIATOR* - Type name.

MAINT CONTROL - Not required. 16.2565 Completed Discrepancy MAF (Supply Asset Induction Document) (Material Condition Tag Missing) Figure 16-84 is an example of a completed VIDS/MAF documented for items inducted from a supply activity for check, test, or service. The following data fields require entries Some data fields are system 16-82 COMNAVAIRFORINST 4790.2C 15 Jan 2017 generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF code D ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the appropriate data (as required). WORK UNIT CODE* - System generated. ACT ORG* - System generated. TRANS - Transaction Code must be 31/32. (Appendix E) M/L* - System generated. A/T - AT Code. (Appendix E) MAL CODE - MAL Code. (Appendix E) I/P - Enter the total number of items being processed.

HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. W/D* - System generated. T/M* - System generated. POSIT - Not required. SFTY/EI - Not required. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated upon initiation. WORK CENTER* - System generated. DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. PILOT/INITIATOR* - System generated. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2566 TD

Compliance Turn-In Document (O-Level) Figure 16-85 illustrates the data groups to be completed by the O-level activity on the TD compliance VIDS/MAF. If the TD is applicable to an end item, such as an aircraft or NC-5, and a component is to be removed and sent to the IMA for modification or inspection as a portion of the TD compliance, the manhours required to remove and reinstall the component will be documented on a TD compliance WO. The O-level will then originate a TD compliance WO for each component forwarded to the I-level activity. This TD compliance WO will accompany the component to the I-level activity for documentation of the assisting TD compliance action, and processing. The I-level activity will sign a copy, indicating receipt of the component and return it to the O-level activity as an IOU receipt. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code TD WORK UNIT CODE* - Enter the specific WUC of the item being processed. TECHNICAL

DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the TEC for equipment. BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. 16-83 COMNAVAIRFORINST 4790.2C 15 Jan 2017 POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the

narrative description of the discrepancy. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2567 TD Compliance (IMA Assist) Figure 16-86 is an example of the VIDS/MAF documented for a TD compliance with the I-level activity assist. The I-level activity will complete the MAF as an assist work center An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code TD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code, system generated. TRANS - Transaction Code must be 47. (Appendix E) M/L* - System generated. A/T - Enter Technical Directive status code, action taken field, must be A. I/P - Must be 0. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - Enter X

(if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number (if applicable); if not enter 00. TYPE EQUIP* - Enter TEC for the equipment. BU/SERNO* - Enter the appropriate bureau/serial number. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). RECEIVED DATE/TIME - System generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW

ITEM - Entries are required when TYPE EQUIP is Y, D, S, H, or G series or whenever an incorporation is being reported against a component related modification. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16-84 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.2568 Turn-In for TD Compliance Figure 16-87 is an example of a VIDS/MAF documented

for items turned in for TD compliance. If the TD compliance is directly applicable to a component, the removal and replacement of the component and the associated man-hours will be documented on a VIDS, MAF, or WO. The O-level activity will then originate a TD compliance WO for the component being forwarded to the I-level activity. This TD compliance WO will accompany the component to the I-level activity for documenting the accomplishment of the TD compliance action and processing. If the component is not ordered, the I-level activity will sign copy 2, indicating receipt of the component and return copy 2 to the O-level activity as an IOU receipt. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code TD. WORK UNIT CODE* - Enter the specific WUC of the item being processed. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number.

TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the Y series TEC for the item or the applicable TEC of the end item. BU/SERNO* - Enter 000000 for Y series equipment or the appropriate bureau/serial number. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any

TD. 16.2569 IMA TD Compliance Figure 16-88 is an example of the VIDS/MAF documented when processing an item for TD compliance at the I-level activity. The I-level activity will complete the remainder of the TD compliance MAF accounting for the items(s) processed in IP data field. An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code TD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code, system generated. TRANS - Transaction Code must be 47. (Appendix E) M/L* - System generated. A/T - Enter Technical Directive status code, action taken field. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code.

(Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). 16-85 COMNAVAIRFORINST 4790.2C 15 Jan 2017 TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the Y series TEC for the item or the applicable TEC of the end item. BU/SERNO* - Enter 000000 if unknown or the appropriate bureau/serial number, must be on the database. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third

time cycle indicates contract number INSTALLED/NEW ITEM - Entries are required when TYPE EQUIP is Y, D, S, H, or G series or whenever an incorporation is being reported against a component related modification. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - System generated. DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2570 TD Compliance Removal Figure 16-89 is an example of a VIDS/MAF documented for a TD compliance removal. TD compliance removals will be documented in the same manner as TD compliance incorporations. An asterisk (*) denotes those data fields completed by the AMSU induction.

ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code, system generated. TRANS - Transaction Code must be 47. (Appendix E) M/L* - System generated. A/T - Enter Technical Directive status code Q. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the Y series TEC for the item or the applicable TEC of the end item. BU/SERNO*

- Enter 000000 if unknown or the appropriate bureau/serial number. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Entries are required in these blocks when TYPE EQUIP is Y, D, S, H, or G series or whenever an incorporation is being reported against a component related modification. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number 16-86 COMNAVAIRFORINST 4790.2C 15 Jan 2017 JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - System generated. DISCREPANCY* -

System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2571 O-Level Turn-In Control Document for Engine Repair Figure 16-90 is an example of a VIDS/MAF turn-in control document for engine repair initiated by the Olevel. The following data fields will be transcribed from O-level turn-in VIDS, MAF, or WO into NALCOMIS AMSU Induction. Type MAF Code D WORK UNIT CODE - Enter the specific WUC for the item being processed. MAL CODE - Enter the conditional MAL Code (if applicable); otherwise leave blank. TYPE EQUIP - Enter the TEC for the engine. BU/SERNO - Enter the PSSN. W/D - Enter the appropriate WD Code.

(Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Enter the appropriate data to reflect the PSSN as a removed component. Leave part number data field blank. Second time cycle denotes removal of a warranted item Third time cycle indicates contract number. JOB CONTROL NUMBER - Utilize O-level JCN. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. Provide inspection JCN for IMA use. INSP JCN - Enter ALPHA JCN from the discrepancy block of the Turn-In MAF. TURN-IN DOCUMENT - Enter the data from the turn-in MAF. SYSTEM REASON - Enter engine SERNO/MOM. NOTE: Before any engine can be inducted for repair or inspection the engine must be loaded to the Configuration Subsystem within NALCOMIS. 16.2572 Supply Asset Engine Depreservation Figure 16-91 is an example of a

VIDS/MAF for a supply asset engine depreservation. The following data fields require entries. WORK UNIT CODE - Enter 049. ACT ORG - System generated. TRANS - System generated 11. M/L - System generated. TYPE EQUIP - Enter the TEC for the engine. BU/SERNO - Enter the PSSN. W/D - System generated O. (Appendix E) T/M - System generated D. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). DISCREPANCY - Enter the narrative description of the discrepancy. JOB CONTROL NUMBER - System generated with Supply Org. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) 16-87 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SYSTEM REASON - Uncan/depreserve. NOTE: Before any engine can be inducted for repair or inspection the engine must be loaded to the Configuration Subsystem within NALCOMIS. 16.2573 Supply Asset Engine (Assist MAF) Test Cell Run Figure 16-92 is an example of a VIDS/MAF for a supply asset engine

(Assist MAF) test cell run. The following data fields require entries. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - System generated. TRANS - System generated 11. M/L - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated V. (Appendix E) T/M - System generated T. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). DISCREPANCY - Enter the narrative description of the discrepancy. JOB CONTROL NUMBER - System generated with Supply Org. WORK CENTER - Enter the appropriate work center code. (Appendix E) SYSTEM REASON - Enter "Test Cell Run". NOTE: Before any engine can be inducted for repair or inspection the engine must be loaded to the Configuration Subsystem within NALCOMIS. 16.2574 Fix-In-Place (Material Not Required) Figure 16-93 is an example of a supporting VIDS/MAF for a fix-in-place repair action not requiring

material. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 11. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable).

SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated from Engine Turn-in MAF. WORK CENTER - Enter the appropriate work center. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. 16-88 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2575 Fix-In-Place (Material Required) Figure 16-94 is an example of a supporting VIDS/MAF for a fix-in-place repair action requiring material. The following data fields require entries

to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Enter the failed parts, identify parts that caused AWP during repair, and/or record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Enter 12 when material is being indexed in failed required material. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can

be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2576 Removal/Replacement of a Tracked Consumable Component Figure 16-95 is an example of a supporting

VIDS/MAF for a removal and replacement of a tracked consumable. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 18. (Appendix E) M/L - System generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) 16-89 COMNAVAIRFORINST 4790.2C 15 Jan 2017 I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X.

(Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item . Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action.

CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2577 Removal/Replacement Subassemblies of a Repairable Component with No Repairable Sub- Figure 16-96 is an example of a supporting VIDS/MAF for a removal and replacement of a repairable with no repairable sub-subassemblies. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 23. (Appendix E) M/L - System generated. A/T - Must

be R. (Appendix E) MAL CODE - Enter the appropriate MAL code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation

of a warranted item. Third time cycle indicates contract number 16-90 COMNAVAIRFORINST 4790.2C 15 Jan 2017 JOB CONTROL NUMBER - System generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2578 Removal/Replacement of a Repairable Component with Repairable Sub-Subassemblies Figure 16-97 is an example of a supporting VIDS/MAF for a removal and replacement of a repairable with repairable sub-subassemblies. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED

SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being removed/replaced. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 23. (Appendix E) M/L - System generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian

date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2579 Facilitate Other Maintenance (FOM) Figure 16-98 is

an example of a supporting VIDS/MAF to FOM. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Enter the specific WUC of the item being processed. 16-91 COMNAVAIRFORINST 4790.2C 15 Jan 2017 ACT ORG - I-level Organization Code; system generated. TRANS - Must be 11. (Appendix E) M/L - Must be 2. A/T - Must be S. (Appendix E) MAL CODE - Must be 800 or 802 if corrosion related. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - Must be O. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI

(if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - System generated from engine turn-in MAF. WORK CENTER - Enter the appropriate work center. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2580 Engine Repair Control Document (Completed VIDS/MAF) Figure 16-99 is an example of a completed VIDS/MAF for an engine repair control document. The following data fields require entries to document a completed

action. Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields completed by the AMSU induction. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - Enter the specific WUC of the item being processed. ACT ORG* - I-level Organization Code; system generated. TRANS - Transaction Code must be 31. (Appendix E) M/L* - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated from engine turn-in MAF. BU/SERNO* - System generated from engine turn-in MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable).

REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. REMOVED/OLD ITEM* - Enter the appropriate data to reflect the PSSN as a removed component. Leave part number data field blank. Second time cycle denotes removal of a warranted item Third time cycle indicates contract number. JOB CONTROL NUMBER* - System generated from engine turn-in MAF. WORK CENTER* - System generated. 16-92 COMNAVAIRFORINST 4790.2C 15 Jan 2017 DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action taken and indicate if RFI or BCM. This section may also be used to report test cell run time CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2581 Supply Asset Engine Build-Up Figure 16-100 is an example of a VIDS/MAF

for a supply asset engine build-up. The following data fields require entries. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - System generated. TRANS - System generated 30. M/L - System generated. TYPE EQUIP - Enter the TEC for the engine. BU/SERNO - Enter the PSSN. W/D - Enter WD Code O. (Appendix E) T/M - Enter TM Code T. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Enter the appropriate data to reflect the PSSN as a removed component. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. Provide inspection JCN for IMA use. JOB CONTROL NUMBER - System generated with Supply Org. WORK CENTER - Enter the appropriate work center code. (Appendix E) SYSTEM REASON - Enter engine serial number and the word "QEC". NOTE: Before any engine

can be inducted for repair or inspection the engine must be loaded to the Configuration Subsystem within NALCOMIS. 16.2582 Engine Component Turn-In for Repair Figure 16-101 is an example of an engine component turned in for repair. An engine component turned in for repair will have the following data fields which are system generated when the part is ordered. WORK UNIT CODE - System generated. MAL CODE - Enter conditional MAL code (if applicable); otherwise leave blank. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. REMOVED/OLD ITEM - System generated. JOB CONTROL NUMBER - System generated. DISCREPANCY - System generated. TURN-IN DOCUMENT - System generated. 16.2583 Engine Component Repair (Completed) Figure 16-102 is an example of a completed engine component repair. To complete the repair use the turn-in document and make the following entries. Some data fields are system generated or updated by using on-line functions.

(*) denotes those data fields system generated from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. 16-93 COMNAVAIRFORINST 4790.2C 15 Jan 2017 FAILED REQUIRED MATERIAL - Enter the failed part(s), identify parts that caused AWP during repair, and/or record supply requisition(s) (if applicable). WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 31 or 32. (Appendix E) M/L - Must be 2, system generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated from engine turn-in MAF. BU/SERNO* - System generated from engine turn-in MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI

(if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. JOB CONTROL NUMBER* - System generated from engine turn-in MAF. WORK CENTER* - Enter the appropriate work center. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2584 Turn-In Document Solely for Major Engine Inspection Figure 16-103 is an example of a turn-in document from O-level activity solely for a major engine inspection. This induction MAF also serves as the inspection control MAF (*) denotes those data fields completed by the AMSU induction. Type

MAF Code "PC" WORK UNIT CODE* - Enter the seven position WUC describing the inspection. TYPE EQUIP* - Enter the TEC of the engine. BU/SERNO* - Enter the PSSN. W/D* - Must be O. T/M* - Must be J. POSIT* - Enter the appropriate PSI (if applicable). REMOVED/OLD ITEM* - Reflects the propulsion system as a removed component. Leave part number blank. JOB CONTROL NUMBER* - Enter O-level inspection JCN. DISCREPANCY* - Enter narrative description of the type of inspection to be performed and initiator. TURN-IN DOCUMENT* - Enter turn-in document from O-level turn-in. 16.2585 Control Document Solely for Major Engine Inspection (Completed) Figure 16-104 an example of a completed control document for a major engine inspection. The I-level activity will fill in the following blocks on the control document for an engine that has been inducted into the I-level activity solely for a major engine inspection. Some data fields are system generated or updated by using on-line functions. (*)

denotes those data fields system generated from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - If only one work center is involved in the inspection, look phase man-hours may be entered on the control document. EMT will be system generated If more than one work 16-94 COMNAVAIRFORINST 4790.2C 15 Jan 2017 center is involved, a separate supporting MAF must be documented for each work center involved in the inspection. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 31. (Appendix E) M/L* - Must be 2, system generated. A/T - Must be 0. (Appendix E) MAL CODE - Must be 000. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. TYPE EQUIP* - System generated from engine turn-in MAF. BU/SERNO* - System generated from engine turn-in MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT

- Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). JOB CONTROL NUMBER* - System generated from engine turn-in MAF. WORK CENTER* - System generated. DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action and indicate if RFI or BCM. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: If the engine is BCM, it should be documented using a fix phase JCN. The turn-in document and E blocks will be transferred to the BCM MAF. The inspection control document for the BCMd engine will be closed out using Transaction Code 11 and 0 items processed. 16.2586 Control Document for Major Engine Inspection (Engine Undergoing Repair) Figure 16-105 is an example of a supporting control document for an engine undergoing

repair that requires a major inspection. I-level maintenance activities will comply with this instruction when engines are turned in for repair. If an inspection is required, the IMA will initiate the MAF The following explains documentation: WORK UNIT CODE - Enter the seven position WUC describing the inspection. TYPE EQUIP - System generated from repair MAF. BU/SERNO - System generated from repair MAF. W/D - System generated. T/M - Must be J, system generated. POSIT - Enter the appropriate PSI (if applicable). JOB CONTROL NUMBER - System generated from engine turn-in MAF, must be A00, B00, etc. DISCREPANCY - Enter narrative description of the type of inspection to be performed. SYSTEM/REASON - Enter PSSN and the word INSP. 16.2587 Major Engine Inspection (Look Phase Supporting Work Center) Figure 16-106 is an example of a look phase supporting work center for a major engine inspection. If more then one work center is involved in the inspection, a separate supporting MAF must be

documented for each work center. Some data fields are system generated or updated by using on-line functions (*) denotes those data fields system generated from the control document created. Inspection look MAFs can be initiated when the control MAF is initiated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. 16-95 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE* - System generated. ACT ORG* - System generated. TRANS - Must be 11. (Appendix E) M/L* - System generated. A/T* - System generated. (Appendix E) MAL CODE* - System generated. (Appendix E) I/P* - Must be 0, system generated. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated from inspection control MAF. BU/SERNO* - System generated from inspection control MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI

(if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. JOB CONTROL NUMBER* - System generated from inspection control MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the MRC numbers to be complied with. CORRECTIVE ACTION - Enter the MRC numbers complied with and item numbers of any discrepancy discovered. Inspection supervisor will assign a fix phase MAF to cover any discrepancy found CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. SYSTEM REASON - Engine SERNO and the word "LOOK". 16.2588 Major Engine Inspection (Fix-In-Place) Figure 16-107 is an example of the VIDS/MAF documented for a fix-in-place for a major

engine inspection. Some data fields are system generated or updated by using on-line functions An asterisk (*) denotes those data fields system generated from the control document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG* - System generated. TRANS - Must be 11 or 12. (Appendix E) M/L* - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field EMT - System generated. TYPE EQUIP* - System generated from inspection control MAF. BU/SERNO* - System generated from inspection control MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate

safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. JOB CONTROL NUMBER* - System generated from inspection control MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the MRC numbers to be complied with. CORRECTIVE ACTION - Enter a narrative description of the corrective action taken. 16-96 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2589 Major Engine Inspection (Fix Phase Removal and Replacement of a Repairable Component) Figure 16-108 is an example of a removal and replacement of a repairable component during a major engine inspection. Some data fields are system generated or updated by using on-line functions An asterisk

(*) denotes those data fields system generated from the control document created in. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - This section will be used to document Supply requisitions. No index WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG* - System generated. TRANS - Must be 23. (Appendix E) M/L* - System generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated from inspection control MAF. BU/SERNO* - System generated from inspection control MAF. W/D* - System generated. T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received

date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates, and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - System generated from inspection control MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter a narrative description of the corrective action taken. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to

the MAF, based on the individuals SMQ. 16.2590 Major Engine Inspection (Component Turn-In) Figure 16-109 is an example of a component turn-in during a major engine inspection. Turn-in MAF is created. WORK UNIT CODE - System generated. TYPE EQUIP - System generated. BU/SERNO - System generated. W/D - System generated. T/M - System generated. POSIT - Enter the appropriate PSI (if applicable). JOB CONTROL NUMBER - System generated. 16-97 COMNAVAIRFORINST 4790.2C 15 Jan 2017 DISCREPANCY - System generated. SYSTEM/REASON - System generated. 16.2591 Major Engine Inspection Completed After Repair Action Figure 16-110 is an example of a major engine inspection control document after repair action. I-level maintenance activities will comply with this instruction when engines are turned in for repair. If an inspection is required, the I-level maintenance activity will initiate the MAF. When the original repair action is complete and the inspection is complete, there should be two

completed control documents MAFs. The transaction code will be 31 for the repair control document and 11 for the inspection control document. Some data fields are system generated or updated by using on-line functions (*) denotes those data fields system generated from the turn-in document. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - If only one work center is involved in the inspection, look phase man-hours may be entered on the control document. EMT will be system generated If more than one work center is involved, a separate supporting MAF must be documented for each work center involved in the inspection. WORK UNIT CODE* - System generated. ACT ORG - I-level organization code; system generated. TRANS - Must be 11. (Appendix E) M/L* - Must be 2; system generated. A/T - Must be 0. (Appendix E) MAL CODE - Must be 000. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. TYPE

EQUIP* - System generated from engine turn-in MAF. BU/SERNO* - System generated from engine turn-in MAF. W/D* - System generated. T/M* - System generated. (Appendix E) REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). JOB CONTROL NUMBER* - System generated from Engine Turn-in MAF. WORK CENTER* - System generated. DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter a narrative description of the corrective action taken. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.2592 Supply Asset (TD Compliance Request) Figure 16-111 is an example of the entries required by the Supply Department for TD compliance on all engines or

engine components held as supply stock. The following explains documentation: TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. TYPE EQUIP - Enter the TEC that identifies the type of engine to which the TD applies. BU/SERNO - Enter the PSSN of the engine or serial number of the component to which the TD applies. 16-98 COMNAVAIRFORINST 4790.2C 15 Jan 2017 REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates control number JOB CONTROL NUMBER - System generated. DISCREPANCY - Enter the narrative description of the discrepancy and initiator.

NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2593 Supply Asset TD Compliance Request (IMA Production Control Entries) Figure 16-112 is an example of the entries required by Production Control for TD compliance on all engines or engine components held as supply stock. An asterisk (*) denotes entries completed when MAF was initiated. ENTRIES REQUIRED SIGNATURE - Check LOGS and REC boxes and upon completion of TD compliance enter name/rate/rank to certify all applicable logs/records have had appropriate entries made. WORK UNIT CODE - Enter the WUC which identifies the engine or component to which the TD applies. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 41 or 47 (as appropriate); system generated. (Appendix E) M/L - Must be 2; system generated. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL

DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the TEC that identifies the type of engine to which the TD applies. BU/SERNO* - Enter the PSSN of the engine or serial number of the component to which the TD applies. JOB CONTROL NUMBER* - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) REMOVED/OLD ITEM - Enter the appropriate data for PSSN. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY* - Enter the narrative description of the discrepancy and initiator. NOTE: Production Control will initiate separate MAFs for each work center involved, using the same JCN as the control document. 16.2594 Supply Asset (TD Compliance Completed) Figure 16-113 is

an example of the completed TD compliance (work center entries) for supply stock. (*) denotes those data fields previously completed by Supply and Production Control. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code, system generated. TRANS - Transaction Code must be 41 or 47 (as appropriate). M/L* - System generated. A/T - Enter TD Status Code. (Appendix E) I/P - Enter the total number of items processed. The following conditions will apply to the number of items processed being recorded. (1) TD Status Codes A or W will require 0s (2) TD Status Codes C, D, P, or Q will require a minimum of 1 in this data field. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E)

16-99 COMNAVAIRFORINST 4790.2C 15 Jan 2017 TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the TEC that identifies the type of engine to which the TD applies. BU/SERNO* - Enter the PSSN of the engine or serial number of the component to which the TD applies. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. JOB CONTROL NUMBER* - System generated. WORK CENTER* - Enter the appropriate work center code. (Appendix E) REMOVED/OLD ITEM - Enter the appropriate data for PSSN. Second time cycle denotes removal of a warranted item. Third time cycle

indicates contract number DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2595 O-Level Engine TD Compliance Request Figure 16-114 is an example of the O-level originating the TD compliance VIDS/MAF (turn-in) using an O-level JCN for engines or engine components sent to the I-level activity solely for TD compliance. The following data fields will be filled in at the I-level activity. Type MAF Code TD WORK UNIT CODE - Enter the specific WUC of the item being processed. TYPE EQUIP - Enter the TEC that identifies the type of engine to which the TD

applies. BU/SERNO - Enter the PSSN of the engine or serial number of the component to which the TD applies; otherwise enter 000000. TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Enter the appropriate data for the PSSN. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. JOB CONTROL NUMBER - Utilize O-level JCN from turn-in. TURN-IN DOCUMENT - Enter the data from turn-in MAF. If engine/component

is not ordered but simply turned in for TD compliance, leave blank. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2596 O-Level Engine TD Compliance Request (Production Control Entries) Figure 16-115 is an example of Production Control entries for an O-level engine TD compliance. (*) denotes those data fields that are system generated. 16-100 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE* - Enter the specific WUC of the item being processed. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the TEC for equipment.

BU/SERNO* - Enter the appropriate bureau/serial number; must be on database. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM* - Enter the appropriate data for the PSSN. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Utilize O-level JCN. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. PRI - Enter 1, 2, or 3. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2597 O-Level Engine TD Compliance Request (Completed) Figure 16-116 is an example of a completed I-level work center VIDS/MAF for an engine TD compliance request. An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is

electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG* - System generated. TRANS - Transaction Code must be 41. (Appendix E) M/L* - System generated. A/T - Enter the appropriate TD Status Code that describes the action taken by the reporting work center. (Appendix E) I/P - Enter the total number of items processed. The following conditions will apply to the number of items processed: (1) TD Status Codes A or W will require 0s. (2) TD Status codes C, D, P, or Q will require a 1 in this data field. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - System generated. TECHNICAL DIRECTIVE ID CODE* - System generated. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - System generated. TECHNICAL DIRECTIVE ID RV* - System generated. TECHNICAL DIRECTIVE ID AM* - System generated. TECHNICAL DIRECTIVE ID PART* - System generated. TECHNICAL DIRECTIVE ID KIT* - System

generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. POSIT* - System generated. SFTY/EI* - System generated. REMOVED/OLD ITEM* - System generated. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. JOB CONTROL NUMBER* - System generated. WORK CENTER* - System generated. (Appendix E) DISCREPANCY* - System generated. 16-101 COMNAVAIRFORINST 4790.2C 15 Jan 2017 CORRECTIVE ACTION - Enter the narrative description of the discrepancy. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.2598 I-Level Originated TD Compliance Request (Engine Component) Figure 16-117 is an example of an I-level originated

TD compliance. documentation: The following explains ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. FAILED/REQUIRED MATERIAL - This section will be used to record supply requisitions. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 41 or 47. (Appendix E) M/L - Enter the appropriate maintenance level. TYPE EQUIP - Enter the TEC that identifies the type of engine to which the TD applies. Enter YE series TEC for components. BU/SERNO - Enter the PSSN of the engine or serial number of the component to which the TD applies, otherwise enter 000000. TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if

applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. REMOVED/OLD ITEM - Enter the FSCM, serial number, part number, and Julian date removed. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - Enter a supply JCN. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. NOTES: 1. TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 2. Production Control will initiate separate MAFs for each work center involved 16.2599 I-Level Originated TD Compliance (Completed) Figure 16-118 is

an example of a completed VIDS/MAF for an I-level originated TD compliance. The following explains documentation. An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL* - This section will be used to record supply requisitions. WORK UNIT CODE* - Enter the specific WUC for the item being processed. ACT ORG* - I-level Organization Code; system generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L* - System generated. 16-102 COMNAVAIRFORINST 4790.2C 15 Jan 2017 A/T - Enter the appropriate TD Status Code. (Appendix E) I/P - Enter the total number of items processed. The following conditions will apply to the number of items processed: (1) TD Status Codes A or W will require 0s. (2) TD Status Codes C, D, P, or Q will require 01. HOURS - System generated from accumulated work hours

field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE* - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - Enter basic number. TECHNICAL DIRECTIVE ID RV* - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM* - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART* - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT* - Enter kit number. TYPE EQUIP* - Enter the TEC for the equipment. BU/SERNO* - Enter the appropriate bureau/serial number; must be on the database. POSIT* - Enter the appropriate PSI (if applicable). SFTY/EI* - Enter the appropriate safety/EI number; if applicable. REMOVED/OLD ITEM* - Enter the FSCM, serial number, part number, and Julian date removed. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED NEW ITEM - Enter the FSCM, serial number, part number, and Julian date installed. Second Time cycle denotes

installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - Supply JCN. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.25100 O-Level Request for TD Compliance Assist (Engine Component) Figure 16-119 is an example of the entries on the turn-in VIDS/MAF from the O-level activity. Type MAF Code TD. WORK UNIT CODE - Enter the specific WUC of the item being processed. TYPE EQUIP - Enter the TEC that identifies the type of engine to which the TD

applies. Enter YE series TEC for components. BU/SERNO - Enter the PSSN of the engine or serial number of the component to which the TD applies, otherwise enter 000000. TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Enter the FSCM, serial number, part number, Julian date removed. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. NOTE: TD identification information must be loaded to the

NALCOMIS Configuration Subsystem prior to the induction of any TD. 16-103 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25101 O-Level Request for TD Compliance Assist (AMSU/Production Control Entries) Figure 16-120 is an example of the entries required by AMSU/Production Control for an O-level TD compliance assist. Type MAF code "TD" ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 41 or 47 (as appropriate). (Appendix E) M/L - Must be 2. TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if

applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. TYPE EQUIP - Enter the TEC that identifies the type of engine to which the TD applies. Enter YE series TEC for components. BU/SERNO - Enter the PSSN of the engine or serial number of the component to which the TD applies; otherwise enter 000000. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Enter the FSCM, serial number, part number, and Julian date removed. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - Utilize O-level JCN. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. PRI - Enter 1, 2, or 3. NOTES: 1. TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 2. Production Control will initiate separate MAFs for each work

center involved, using the same JCN as the control document. 16.25102 O-Level Request for TD Compliance Assist (Completed) Figure 16-121 is an example of a completed VIDS/MAF for an O-level TD compliance assist. The following explains documentation. An asterisk (*) denotes those data fields that are system generated. Type MAF Code TD. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG* - System generated. TRANS - Enter the appropriate Transaction Code. (Appendix E) M/L* - System generated. A/T - Enter the appropriate TD Status Code. (Appendix E) I/P - Must be 0. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - System generated. TECHNICAL DIRECTIVE ID CODE* - System generated. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - System generated. TECHNICAL DIRECTIVE ID RV* - System

generated. TECHNICAL DIRECTIVE ID AM* - System generated. 16-104 COMNAVAIRFORINST 4790.2C 15 Jan 2017 TECHNICAL DIRECTIVE ID PART* - System generated. TECHNICAL DIRECTIVE ID KIT* - System generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. POSIT* - System generated. SFTY/EI* - System generated. REMOVED/OLD ITEM* - System generated. INSTALLED NEW ITEM - Enter the FSCM, serial number, part number, and Julian date installed. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - System generated. WORK CENTER* - System generated. (Appendix E) DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTES: 1. TD identification

information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 2. If an engine or engine component sent to the IMA for TD compliance is found to require repair, the IMA will inform the O-level activity, which must provide a turn-in MAF for documenting the repair action. The original TD compliance MAF is destroyed and Production Control initiates a replacement TD compliance MAF using a supply JCN. 16.25103 O-Level Turn-In Control Document for Engine Repair (Modular Engine) Figure 16-122 is an example of an O-level turn-in VIDS/MAF for a modular engine repair. Type MAF Code D. WORK UNIT CODE - Enter the specific WUC for the item being processed. MAL CODE - Enter the conditional MAL code (if applicable); otherwise leave blank. TYPE EQUIP - Enter the TEC of the engine. BU/SERNO - Enter the PSSN. W/D - Enter the applicable WD code. (Appendix E) T/M - Enter the appropriate TM code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable).

SAFETY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Reflects the PSSN as a removed component on the turn-in MAF. Leave part number blank. Second time cycle denotes removal of a warranted item Third time cycle indicates contract number. DISCREPANCY - Enter narrative description of the discrepancy and initiator. Provide inspection JCN for IMA use. INSPECTION JCN - Enter inspection JCN from discrepancy field. TURN-IN DOCUMENT - Transcribe the data from O-level turn-in. 16.25104 Fix-In-Place (Not Requiring Material) Figure 16-123 is an example of a supporting VIDS/MAF for a fix-in-place repair action on a modular engine not requiring material. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - System

generated from engine turn-in MAF. ACT ORG - I-level Organization Code. System generated TRANS - Must be 11. (Appendix E) 16-105 COMNAVAIRFORINST 4790.2C 15 Jan 2017 M/L - Must be 2; system generated. A/T - System generated from engine turn-in MAF. MAL CODE - System generated from engine turn-in MAF. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER -

JCN system generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25105 Fix-In-Place (Requiring Material) Figure 16-124 is an example of a supporting VIDS/MAF for a fix-in-place repair action on a modular engine requiring material. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Enter the failed parts, identify parts

that caused AWP during repair, and/or record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code, system generated. TRANS - Enter 12 when material is being indexed in failed/required material. (Appendix E) M/L - System generated from engine turn-in MAF, must be 2. A/T - System generated from engine turn-in MAF. MAL CODE - System generated from engine turn-in MAF. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the

appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. JOB CONTROL NUMBER - JCN system generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. 16-106 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25106 Removal/Replacement of a Repairable Subassembly with No Repairable SubSubassemblies Figure 16-125 is an example of a removal/replacement of a repairable subassembly with no repairable subsubassemblies. The following data fields require entries for a completed action Some data fields are system generated or updated by using

on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level organization code, system generated. TRANS - Must be 23. (Appendix E) M/L - System generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time;

enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - JCN system generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25107

Removal/Replacement of a Repairable Module/Component with Repairable SubSubassemblies Figure 16-126 is an example of a supporting VIDS/MAF for a removal/replacement of repairable modules/components with repairable sub-subassemblies. The following data fields require entries for a completed action. Some data fields are system generated or updated by using on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 23. (Appendix E) M/L - System generated. 16-107 COMNAVAIRFORINST 4790.2C 15 Jan 2017 A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE

EQUIP - System generated from engine turn-in MAF. BU/SERNO - System generated from engine turn-in MAF. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - JCN system generated from engine turn-in MAF. WORK CENTER - Enter the appropriate Work Center

Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25108 Engine Repair Control Document (Completed) Figure 16-127 is an example of a completed engine repair control document. Use the turn-in document and complete the following blocks. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions An asterisk (*) denotes those data fields completed by the AMSU induction. Type MAF Code "D" ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System

generated. ACT ORG* - System generated. TRANS - Transaction code must be 31. (Appendix E) M/L* - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. W/D* - System generated. (Appendix E) T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates, and times. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. WORK CENTER* - System generated. (Appendix E) 16-108 COMNAVAIRFORINST 4790.2C 15 Jan 2017 DISCREPANCY* - System generated.

CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25109 Turn-In of Repairable Module with Repairable Sub-Subassemblies Figure 16-128 is an example of a turn-in VIDS/MAF for repairable sub-subassemblies. An engine module turned in for repair will have the following data fields system generated when the part is ordered. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* - System generated. MAL CODE - Enter conditional MAL code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for modules with an X in the fourth position. BU/SERNO* - System generated. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated.

DISCREPANCY* - System generated. TURN-IN DOCUMENT - System generated. 16.25110 Removal/Replacement of a Repairable Sub-Subassembly from a Module Figure 16-129 is an example of a supporting VIDS/MAF for a removal/replacement of a repairable subsubassembly from a module. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being removed/replaced. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 23. (Appendix E) M/L - System generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP

- System generated for the engine module with fourth position X. BU/SERNO - System generated for the engine module. W/D - System generates W; it can be changed to R or X. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code.

(Appendix E) 16-109 COMNAVAIRFORINST 4790.2C 15 Jan 2017 DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25111 Module Repair (Completed) Figure 16-130 is an example of a completed VIDS/MAF for module repair. Use the turn-in document and complete the following blocks. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - Enter the specific WUC

for the item being removed/replaced. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 31. (Appendix E) M/L - Must be 2; system generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated for the engine module with fourth position X. BU/SERNO* - System generated for the engine module. W/D* - System generates W; it can be changed to R or X. (Appendix E) T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates, and times. REMOVED/OLD ITEM* - Enter the appropriate data for

the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - System generated. WORK CENTER* - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY* - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25112 Turn-In of Repairable Sub-Subassembly from a Repairable Component Figure 16-131 is an example of a turn-in VIDS/MAF for a repairable sub-subassembly from a repairable component. A repairable sub-subassembly turned in for repair will have the following data fields system generated when the part is ordered. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* -

System generated. MAL CODE - Enter conditional MAL Code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for modules with an X in the fourth position. BU/SERNO* - System generated to reflect module serial number. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. 16-110 COMNAVAIRFORINST 4790.2C 15 Jan 2017 JOB CONTROL NUMBER* - System generated. DISCREPANCY* - System generated. TURN-IN DOCUMENT - System generated. 16.25113 Repair of a Repairable Component with Required Material Figure 16-132 is an example of a repair of a repairable component with required material. Use the turn-in document and complete the following blocks. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is

electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE* - Enter the specific WUC for the item being removed/replaced. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 31 or 32. (Appendix E) M/L - Must be 2; system generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated for the engine module with fourth position X. BU/SERNO* - System generated for the engine module. W/D* - System generates W; it can be changed to R or X. (Appendix E) T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time;

enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25114 Turn-In of a Repairable Component Sub-Subassemblies Figure 16-133 is an example of a turn-in VIDS/MAF for a repairable component. Use for turn-in of defective sub-subassembly for sub-subassembly repair in the I-level

activity when the repair of these items is accomplished as a separate job. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* - System generated. MAL CODE - Enter conditional MAL code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for modules with an X in the fourth position. BU/SERNO* - System generated to reflect module serial number. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. 16-111 COMNAVAIRFORINST 4790.2C 15 Jan 2017 DISCREPANCY* - System generated. TURN-IN DOCUMENT* - System generated. 16.25115 Repair of a Sub-Subassembly from a Component Subassembly (Completed) Figure 16-134 is an example of a completed VIDS/MAF for repair of a sub-subassembly from a component subassembly. Use the turn-in document and complete the following blocks The following data fields require entries to document a completed action. Some data fields are system

generated or updated by using on-line functions. An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE* - Enter the specific WUC for the item being removed/replaced. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 31 or 32. (Appendix E) M/L - Must be 2; system generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP* - System generated for the engine module with fourth position X. BU/SERNO* - System generated for the engine module. W/D* - System generates W; it can be changed to R or X. (Appendix E) T/M* - System generated. (Appendix E) POSIT - Enter

the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates, and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25116 Removal/Replacement of a Repairable

Sub-Subassembly from a Module Figure 16-135 is an example of a removal and replacement of a repairable sub-subassembly VIDS/MAF from a module. The following data fields require entries to document a completed action Some data fields are system generated or updated by using on-line functions. An asterisk (*) denotes those data fields that are system generated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE* - Enter the specific WUC for the item being removed/replaced. ACT ORG - I-level Organization Code; system generated. TRANS - Transaction Code must be 23. (Appendix E) M/L - Must be 2; system generated. A/T - Must be R. (Appendix E) 16-112 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT -

System generated. TYPE EQUIP* - System generated for the engine module with fourth position X. BU/SERNO* - System generated for the engine module. W/D* - System generates W; it can be changed to R or X. (Appendix E) T/M* - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM* - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the

individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - System generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) 16.25117 Turn-In of a Repairable Sub-Subassembly from a Module Figure 16-136 is an example of a turn-in of a repairable sub-subassembly from a module. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* - System generated. MAL CODE - Enter conditional MAL Code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for modules with an X in the fourth position. BU/SERNO* - System generated to reflect module serial number. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. DISCREPANCY* - System generated. TURN-IN DOCUMENT* - System generated. 16.25118 O-Level Turn-In Control Document Modular Engine Turn-In (Solely for Major Engine Inspection)

Figure 16-137 is an example of an O-level turn-in control document. Use for turn-in from the O-level activity to accomplish the induction of the engine. Type MAF Code PC WORK UNIT CODE - Enter the seven position WUC describing the inspection. TYPE EQUIP - Enter the TEC of the engine. BU/SERNO - Enter the PSSN for the engine. W/D - Must be O. T/M - Must be J. POSIT - Enter the appropriate PSI (if applicable). REMOVED/OLD ITEM - Reflects the PSSN as a removed component. Leave part number blank JOB CONTROL NUMBER - Use O-level phase JCN. DISCREPANCY - Enter narrative description of the type of inspection to be performed and initiator. TURN-IN DOCUMENT - Use O-level turn-in document number. SYSTEM/REASON - Enter the engine PSSN and the word MOM. 16-113 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25119 Major Modular Engine Inspection (Look Phase Supporting Work Center) Figure 16-138 is an example of a look phase supporting work center for a major engine inspection not requiring any

material. If more than one work center is involved in the inspection, a separate supporting MAF must be documented for each work center. The following data fields require entries for a completed action. Some data fields are system generated or updated by using on-line functions ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Same as control document. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 11, system generated. (Appendix E) M/L - System generated. A/T - Must be 0. (Appendix E) MAL CODE - Must be 000. (Appendix E) I/P - Must be 0. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Same as control document, system generated. BU/SERNO - Same as control document, system generated. W/D - Same as control document, system generated. (Appendix E) T/M - Same as control document, system generated.

(Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. DISCREPANCY - Enter the card numbers of the MRC to be complied with. CORRECTIVE ACTION - Enter the MRC card numbers complied with and item numbers of any discrepancy discovered. Any discrepancy found will have a fix phase JCN assigned CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) SYSTEM/REASON - Enter the engine serial number and the word LOOK. 16.25120 Major Modular Engine

Inspection (Look Phase Supporting Work Center) (Engine Test Cell Run) Figure 16-139 is an example of a look phase supporting work center for a major engine inspection (Engine Test Cell Run). The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE - Same as control document. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 11, system generated. (Appendix E) M/L - System generated. A/T - Must be 0. (Appendix E) MAL CODE - Must be 000. (Appendix E) I/P - Must be 0. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Same as control document, system generated. 16-114 COMNAVAIRFORINST 4790.2C 15 Jan 2017 BU/SERNO - Same as control document, system generated. W/D - Same as

control document, system generated. (Appendix E) T/M - Same as control document, system generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. DISCREPANCY - Enter the card numbers of the MRC to be complied with. CORRECTIVE ACTION - Enter the MRC card numbers complied with and item numbers of any discrepancy discovered. Any discrepancy found will have a fix phase JCN assigned CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix

E) SYSTEM/REASON - Enter the engine serial number and the word RUN. 16.25121 Major Engine Inspection (Fix-In-Place) Figure 16-140 is an example of a fix-in-place VIDS/MAF during a major engine inspection. The following data fields require entries for a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the failed parts(s), identify parts that caused AWP during repair, and/or record supply requisition(s) (if applicable). WORK UNIT CODE - Enter the specific WUC. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 11 or 12. (Appendix E) M/L - System generated. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from

accumulated work hours field. EMT - System generated. TYPE EQUIP - Same as control document, system generated. BU/SERNO - Same as control document, system generated. W/D - Must be M, system generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER -

Enter the appropriate Work Center Code. (Appendix E) 16-115 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25122 Major Engine Inspection (Fix Phase Module Replacement) Figure 16-141 is an example of a fix phase module replacement VIDS/MAF during a major engine inspection. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC for the item being requisitioned. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 23. (Appendix E) M/L - Must be 2; system generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated.

TYPE EQUIP - Same as control document. BU/SERNO - Same as control document. W/D - Must be M. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data to reflect the old module. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data to reflect the new module. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR -

Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) 16.25123 Major Engine Inspection (Module Turn-In) Figure 16-142 is an example of a fix phase module replacement MAF during a major engine inspection. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* - System generated. MAL CODE - Enter conditional MAL code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for modules with an X in the fourth position. BU/SERNO* - System generated to reflect module serial number. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. DISCREPANCY* - System generated. TURN-IN DOCUMENT* - System generated. 16-116 COMNAVAIRFORINST 4790.2C

15 Jan 2017 16.25124 Major Engine Inspection (Fix Phase Repairable Component Replacement) Figure 16-143 is an example of a fix phase repairable component replacement VIDS/MAF during a major engine inspection. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 23. (Appendix E) M/L - Must be 2; system generated. A/T - Must be R. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated for the engine. BU/SERNO - System

generated for the engine. W/D - System generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to

the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) 16.25125 Major Engine Inspection (Fix Phase Component Turn-In) Figure 16-144 is an example of a fix phase component turn-in VIDS/MAF during a major engine inspection. An asterisk (*) denotes those data fields that are system generated. WORK UNIT CODE* - System generated. MAL CODE - Enter conditional MAL Code (if applicable); otherwise leave blank. TYPE EQUIP* - System generated for engine TEC. BU/SERNO* - System generated to reflect engine. W/D* - System generated. T/M* - System generated. REMOVED/OLD ITEM* - System generated. JOB CONTROL NUMBER* - System generated. DISCREPANCY* - System generated. TURN-IN DOCUMENT - System generated. 16-117 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25126 Completed Major Inspection Control Document

(Modular Engine Turned-In Solely for Major Inspection) Figure 16-145 is an example of a major inspection control document for an engine turned-in solely for inspection. The following data fields require entries for a completed action Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - If only one work center is involved in the inspection, look phase man-hours and EMT may be entered on the control document. If more than one work center is involved, a separate supporting MAF must be documented for each work center involved in the inspection. WORK UNIT CODE - Enter the specific WUC for the item being processed. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 31. (Appendix E) M/L - Must be 2; system generated. A/T - Must be 0. (Appendix E) MAL CODE - Must be 000. (Appendix E) I/P - Must be 1. HOURS - System generated from

accumulated work hours field. EMT - System generated. TYPE EQUIP - System generated for the engine. BU/SERNO - System generated for the engine. W/D - System generated. (Appendix E) T/M - System generated. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. REMOVED/OLD ITEM - Reflects the PSSN as a removed component on the control document only. All other supporting documents will not have the PSSN identification listed in the "E" record. Second time cycle denotes removal of a warranted item. Third time cycle indicates contract number DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED

BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) 16.25127 O-Level Activity Request for a Modular Engine TD Compliance by I-Level Activity Figure 16-146 is an example of the O-level originating the TD compliance VIDS/MAF using an O-level JCN for modular engine sent to the I-level activity solely for TD compliance. Type MAF Code TC WORK UNIT CODE - Enter the module or component WUC. TECHNICAL DIRECTIVE ID INT - Enter X (if applicable). TECHNICAL DIRECTIVE ID CODE - Enter appropriate code. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO. - Enter basic number TECHNICAL DIRECTIVE ID RV - Enter revision (if applicable). TECHNICAL DIRECTIVE ID AM - Enter amendment (if applicable). TECHNICAL DIRECTIVE ID PART - Enter part (if

applicable). TECHNICAL DIRECTIVE ID KIT - Enter kit number. TYPE EQUIP - Enter the TEC for module to which the TD applies. BU/SERNO - Enter the appropriate bureau/serial number for the module. POSIT - Enter the appropriate PSI (if applicable). 16-118 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SFTY/EI - Enter the appropriate safety/EI number (if applicable). REMOVED/OLD ITEM - Must be filled in under the following circumstances: 1) If module will have a part number change; 2) If the TD applies to a component within the module, enter the information concerning the component. Second time cycle denotes removal of a warranted item Third time cycle indicates contract number. JOB CONTROL NUMBER - Use O-level JCN. DISCREPANCY - Enter the narrative description of the discrepancy and initiator. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.25128 Production Control Entries (O-Level Activity Request for TD

Compliance) Figure 16-147 is an example of Production Control entries on an O-level activity request for a TD compliance VIDS/MAF. An asterisk (*) indicates data entered from the O-level turn-in document. WORK UNIT CODE* - System generated. ACT ORG* - System generated. TRANS - Transaction Code must be 41 or 47 (as appropriate). (Appendix E) M/L* - System generated. Must be 2 TECHNICAL DIRECTIVE ID INT* - System generated. TECHNICAL DIRECTIVE ID CODE* - System generated. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - System generated. TECHNICAL DIRECTIVE ID RV* - System generated. TECHNICAL DIRECTIVE ID AM* - System generated. TECHNICAL DIRECTIVE ID PART* - System generated. TECHNICAL DIRECTIVE ID KIT* - System generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. POSIT - Enter the appropriate PSI (if applicable). SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter

the appropriate Julian date and time. REMOVED/OLD ITEM - Must be filled in under the following circumstances: 1) If module will have a part number change; 2) If the TD applies to a component within the module, enter the information concerning the component. Second time cycle denotes removal of a warranted item Third time cycle indicates contract number. DISCREPANCY - Enter the narrative description of the discrepancy and initiator. JOB CONTROL NUMBER - Use O-level JCN. WORK CENTER* - System generated. (Appendix E) NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.25129 Completed TD Compliance (Applies to a Module With No Module or Repairable Component P/N Change) Figure 16-148 is an example of a TD compliance VIDS/MAF documenting an end item TD with no removed component. For each component removed, a separate TD compliance turn-in document is generated per paragraph 16.2520 The following data fields require

entries to document a completed action. Some data fields are system generated or updated by using on-line functions NOTE: All TDs must reside in the configuration sub-system prior to the TD MAF being initiated. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. 16-119 COMNAVAIRFORINST 4790.2C 15 Jan 2017 WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Must be 41. (Appendix E) M/L - Must be 1. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Leave blank. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Not required. T/M - Not required. POSIT - Not

required. SAFETY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates/times. REMOVED/OLD ITEM - Enter the appropriate data, if required. INSTALLED/NEW ITEM - Enter the appropriate data, if required. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code (Appendix E). DISCREPANCY - Enter the narrative description. CORRECTIVE ACTION - Enter the narrative description. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF. Not required 16.25130 TD Compliance (Applies to a Module With P/N Change) Figure 16-149 is an example of a VIDS/MAF

documented when processing an item for TD compliance at the IMA. The IMA will complete the remainder of the TD compliance MAF accounting for the item(s) processed in an IP data field. An asterisk (*) denotes those data fields previously completed by AMSU induction. Type MAF Code TD ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. WORK UNIT CODE* - System generated. ACT ORG - I-level Organization Code; system generated. TRANS - Must be 47. (Appendix E) M/L* - System generated. A/T - Enter the TD Status Code. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TECHNICAL DIRECTIVE ID INT* - System generated. TECHNICAL DIRECTIVE ID CODE* - System generated. (Appendix E) TECHNICAL DIRECTIVE ID BASIC NO.* - System generated. TECHNICAL DIRECTIVE ID RV* - System generated. TECHNICAL DIRECTIVE ID AM* - System

generated. TECHNICAL DIRECTIVE ID PART* - System generated. TECHNICAL DIRECTIVE ID KIT* - System generated. TYPE EQUIP* - System generated. BU/SERNO* - System generated. POSIT* - System generated. 16-120 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SFTY/EI - Enter the appropriate safety/EI number (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates, and times. REMOVED/OLD ITEM* - System generated. INSTALLED NEW ITEM - Entries are required when a Y, D, S, H, or G series TEC is entered or whenever an incorporation is being reported against a component related modification. Second time cycle denotes installation of a warranted item. Third time cycle indicates contract number JOB CONTROL NUMBER* - System generated. WORK CENTER* - System generated. DISCREPANCY* - System generated. CORRECTIVE ACTION - Enter the narrative description of

the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. NOTE: TD identification information must be loaded to the NALCOMIS Configuration Subsystem prior to the induction of any TD. 16.25131 TD Compliance (Applies to a Component Within A Module) Figure 16-150 is an example of a completed off-equipment TD compliance action. Off-equipment TD compliance actions are documented by completing the TD compliance turn-in document. The following data fields require entries to document a completed action. Some data fields are system generated or updated by using on-line functions. ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Enter the parts required information. WORK UNIT CODE - Enter

the specific WUC of the item being processed. ACT ORG - System generated. TRANS - Must be 47. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Leave blank. I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the TEC for the item being processed. BU/SERNO - Enter the appropriate bureau/serial number. W/D - Not required. T/M - Not required. POSIT - PSI (if applicable). SAFETY/EI - Not required. TECHNICAL DIRECTIVE ID - Enter the appropriate TD information for the Code/Basic No/Kit. REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates/times. REMOVED/OLD ITEM - Enter the appropriate data, if required. INSTALLED/NEW ITEM - Enter the appropriate data, if required. JOB CONTROL NUMBER - System generated upon

Production Control approval. WORK CENTER - Enter the appropriate Work Center Code (Appendix E). DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF. Not required 16-121 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.25132 Engine or Module Cannibalization (For A Supported Activity) Figure 16-151 is an example of cannibalization action of a removal and subsequent replacement of a component from an engine or module under repair. Removed for a supported activity Some data fields are system generated or updated by using on-line functions. The following explains documentation: ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate

data. FAILED/REQUIRED MATERIAL - This section will be used to document or record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being cannibalized. ACT ORG - I-level Organization Code, system generated. TRANS - Must be 18. (Appendix E) M/L - Must be 2. A/T - Must be T. (Appendix E) MAL CODE - Must be 813, 814, 815, 816, 817, or 818. (Appendix E) I/P - Must be 1. HOURS - System generated from accumulated work hours field. EMT - System generated. TYPE EQUIP - Enter the general TEC for the engine or module, for example, JHDX. BU/SERNO - Enter the SERNO of the engine or SERNO of the uninstalled module. W/D - Must be O, system generated. (Appendix E) T/M - Must be B, system generated. (Appendix E) REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. REMOVED/OLD ITEM - Enter the FSCM, serial number, part number, Julian date removed, and appropriate time/cycle data for the removed item.

INSTALLED/NEW ITEM - Enter the FSCM, serial number, part number, Julian date removed, and appropriate time/cycle data for the installed item. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates and times. DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action taken. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. JOB CONTROL NUMBER - JCN system generated from module inspection control MAF. PRI - Production control or authorized personnel will fill in this data field to approve the initiated MAF. SYSTEM/REASON - Enter a brief (snap shot) description of the reported discrepancy. 16.25133 Removal and Replacement of Cartridges (CART), Cartridge Activated Devices (CAD), and Propellant Actuated Devices(PAD) (I-Level

Maintenance) Figure 16-152 is an example of a VIDS/MAF documented for the removal and replacement of aircraft installed explosive devices. The following explains documentation: ENTRIES REQUIRED SIGNATURE - Check the appropriate field, signature is electronically posted. ACCUMULATED WORK HOURS - Enter the appropriate data. FAILED/REQUIRED MATERIAL - Record supply requisitions. WORK UNIT CODE - Enter the specific WUC of the item being processed. ACT ORG - I-level Organization Code. System generated TRANS - Must be 18. (Appendix E) M/L - Must be 2. A/T - Enter the appropriate AT Code. (Appendix E) MAL CODE - Enter the appropriate MAL Code. (Appendix E) I/P - Enter the total number of items processed. HOURS - System generated from accumulated work hours field. EMT - System generated. 16-122 COMNAVAIRFORINST 4790.2C 15 Jan 2017 TYPE EQUIP - Enter the TEC for the item being processed; first position must be D, G, H, M, S, V, or Y. BU/SERNO - Enter the appropriate bureau/serial number,

must be on database. W/D - Enter the appropriate WD Code. (Appendix E) T/M - Enter the appropriate TM Code. (Appendix E) POSIT - Enter the appropriate PSI (if applicable). REPAIR CYCLE - Received date/time; system generated. In-work/completed date/time; enter the appropriate Julian date and time. MAINTENANCE/SUPPLY REC - Enter the appropriate job status, Julian dates/times. REMOVED/OLD ITEM - Enter the appropriate data for the removed/old item. The part number block (E23) shall reflect the lot number of the device removed. The time/cycle block (E42) shall have an entry using time/cycle prefix code H and the container open date (MMYY) for CARTs or CADs and the manufacture date (MMYY) for PADs. INSTALLED/NEW ITEM - Enter the appropriate data for the installed/new item. The part number block (G23) shall reflect the lot number of the device installed. The time/cycle block (G38) shall have an entry using time/cycle prefix code H and the container open date (MMYY) for CARTs or CADs and the

manufacture date (MMYY) for PADs. JOB CONTROL NUMBER - System generated upon Production Control approval. WORK CENTER - Enter the appropriate Work Center Code. (Appendix E) DISCREPANCY - Enter the narrative description of the discrepancy. CORRECTIVE ACTION - Enter the narrative description of the corrective action. CORRECTED BY/INSPECTED BY/SUPERVISOR - Signatures are electronically posted to the MAF, based on the individual SMQ/PASSWORD. MAINT CONTROL - Signature is electronically posted to the MAF, based on the individuals SMQ. 16.25134 Fleet Readiness Centers (FRC) NALCOMIS Optimized Intermediate Activity (OIMA) Documentation Procedures and Processes This paragraph provides procedures and processes for the documentation of maintenance actions and associated Supply data in the FRC, using NALCOMIS. The FRC sites are responsible for training the D-level Artisan on OIMA NALCOMIS procedures and ensuring the documentation is accomplished correctly. NOTE: The FRC NALCOMIS Documentation

Handbook provides additional information, with illustrations. 16.251341 I-Level Induction, D-Level RFI A component is received from supply and is inducted by JASU through the automated or manual induction process into an I-level work center, such as in work and order parts. If the determination is made that the repair action is beyond their repair capability, the following will occur: a. The I-level work center performs a closeout MAF to document man hours invested in the attempt to repair. b. Production Control changes the work center code to the appropriate D-level work center code that will perform the repair. c. The D-level work center goes in work, orders parts, repairs the component, and signs off the MAF as RFI. NOTE: All parts required by an artisan to accomplish the repair must be ordered with a D-level work center and identified as a failed part (indexed) on the MAF. 16.251342 I-Level Induction, D-Level RFI Documentation Procedures The following explains documentation:

16-123 COMNAVAIRFORINST 4790.2C 15 Jan 2017 a. The I-level work center will change the current status of the MAF to M1 (AWM Depot) b. The work center will update work hours and tools and complete Transaction Code, Action Taken Code, Malfunction Code, and Items Processed prior to validating the MAF. The work center shall use the “Notes” tab to provide additional information to the D-level work center. c. The work center will select the Validate button and correct any errors (if applicable) d. The work center will create a closeout MAF to account for the I-level technician’s time attempting the repair and troubleshooting the component by checking the “Trbl shoot” button in the MAF Sign Off Tab and follow the prompts. e. A closeout MAF is automatically initiated using the same JCN, but with a new MCN The closeout MAF is automatically filled out with all pertinent information and can be located under the “Awaiting Supervisor” mailbox or in the originating work center’s

workload queue. f. NOTE: Select the closeout MAF. All required data under Basic MAF will be completed automatically Do not attempt to make changes to a closeout MAF. If changes are attempted, Discrepancy MAF validations re invoked, resulting in numerous problems and errors. g. A Supervisor Sign-off is all that is required on a closeout MAF h. The original MAF EMT and man-hours are closed out The MAF is still in an M1 status and still has the I-level work center code on it. i. Production Control needs to change the work center block to the appropriate D-level work center, change the Awaiting Maintenance Code, and delete all CO accumulated work hours under the JS Hours tab (if required). j. The D-level work center can go in work, order parts, update accumulated work hours, shift, and tool box information. NOTE: All parts required by an artisan to accomplish the repair must be ordered within a D-level work center and identified as a failed part (indexed) on the MAF. k. After the

D-level work center completes repair, the artisan updates the job status to M1 This allows the artisan to update/change the MAF prior to moving to a JC status. If the artisan is a contractor support services (CSS), the ETS block must be checked prior to MAF Validation. l. On the Sign-off tab, validate the MAF Errors will be displayed in the Error Message List subscreen All errors must be corrected prior to the MAF being moved to a JC status m. Once all errors are corrected, validate MAF again, change the MI status to JC and perform signoffs in the Corrected by, Inspected by and Supervisor blocks NOTE: Specific OIMA NALCOMIS workarounds are required to allow artisans to inspect their own work. Separate logons are required to complete the “corrected by” block and the “inspected by” block. (Refer to the FRC NALCOMIS Handbook for details) n. Production Control scan locate the sign-off in the PC Review Mailbox and clear it 16-124 COMNAVAIRFORINST 4790.2C 15 Jan 2017 16.251343

I-Level, D-Level Repair, and I-Level RFI A component is received from JASU and inducted into an I-level work center. The I-level work center determines that depot repair is required; however, the final RFI function belongs to the I-level work center. The following will occur: a. The I-level work center performs all initial work required and performs a closeout MAF to document man-hours invested in the initial maintenance. b. Production Control changes the work center code to the D-level work center that will perform the next step of repair, changing the Awaiting Maintenance Code, and deleting all CO accumulated work hours under the JS Hours tab (if required). c. The D-level work center goes in work, orders parts, and completes their portion of the repair d. The D-level work center then performs a closeout MAF to document man hours invested in their portion of the repair. e. Production Control changes the work center code to the I-level work center that will perform the final steps of

repair, changing the Awaiting Maintenance Code, and deleting all CO accumulated work hours under the JS Hours tab (if required). 16.251344 I-level, D-level Repair, I-level RFI Documentation Procedures The following explains documentation: a. A component is received from Supply and is inducted by JASU through the automated or manual induction process into an I-level work center. b. The I-level work center can go in work, order parts, etc c. The I-level work center determines that required repair is beyond I-level capability and will change the status of the MAF to M1 (AWM Depot). d. The I-level work center will notify Production Control of the need for the D-level work center repair. e. The I-level work center must validate the repair MAF to ensure that it is as correct as possible before initiating a closeout MAF. All tools must be accounted for on the MAF and all work hours must be correct. The work center shall use the “Notes” tab to provide additional information to the D-level

work center. f. The I-level work center will generate a closeout MAF by selecting the “Trbl Shoot” button and following the prompts. The closeout MAF is automatically generated, filled out, and the man hours are moved. The original MAFs man-hours and EMT are zero NOTE: Do not attempt to make changes to a closeout MAF. If changes are attempted, Discrepancy MAF validations are invoked, resulting in numerous problems and errors. g. The Supervisor sign-off is all that is required on the closeout MAF h. Production Control needs to change the work center block to the appropriate D-level work center and delete all CO accumulated work hours under the JS Hours tab (if required). 16-125 COMNAVAIRFORINST 4790.2C 15 Jan 2017 i. The D-level work center Artisan can now go in work, order repairable and consumable parts and complete the repair action. NOTE: j. All parts required by an artisan to accomplish the repair must be ordered with a D-level work center and identified as a failed

part (indexed) on the MAF. Once the repair is complete, the D-level work center will update the MAF to M6 Status. k. The D-level work center will notify Production Control that the repair is complete and the need for further I-level work center maintenance. l. The D-level work center will validate the MAF to ensure the MAF is correct and all tools have been accounted for. m. The D-level work center may use the “Notes” tab to provide additional information that assists the I-level technicians in the final RFI of the component. n. If the artisan is a CSS, the ETS block must be verified to be checked prior to closing out the MAF The D-level work center will generate a closeout MAF by selecting the “Trbl Shoot” button and following the prompts. The closeout MAF is automatically generated, filled out, and the man hours are moved The original MAFs man-hours and EMT are now zero. o. The Supervisor sign-off is all that is required on the closeout MAF p. Production Control will change

the work center code on the MAF to the I-level work center and delete all CO accumulated work hours under the JS Hours tab (if required). q. The I-level work center completes the maintenance/RFI run and signs-off MAF NOTE: If parts were ordered by an artisan to accomplish the repair, the I-level work center must use Transaction Code 32 when completing MAF. Failure to use Transaction Code 32 will result in loss of visibility of artisan material requirements in the up-line data. 16.251345 D-Level SRA Induction and RFI This scenario is basically the same as an internal SRA repair performed currently, but the ICRL will need to be updated to reflect the D-level work center’s capability to repair the SRA. 16.251346 D-level SRA Induction and RFI Documentation Procedures The following explains documentation: a. The turn-in MAF is generated from the I-level or D-level work center’s DDSN b. The MAF and retrograde SRA will be inducted to the D-level work center through JASU and Production

Control. c. The D-level work center can go in work, order parts, document man-hours, RFI the part, and ensure MAF is validated prior to sign-off attempt. If the artisan is a CSS, the ETS block must be checked NOTES: 1. All parts required by an artisan to accomplish the repair must be ordered with a D-level work center and identified as a failed part (indexed) on the MAF. 2. The FRC NALCOMIS Handbook shows examples of processing if SRA was repaired, returned to supply and issued back to a D-level work center for WRA repair. The D-level 16-126 COMNAVAIRFORINST 4790.2C 15 Jan 2017 work center will use the same process as internal FRC/MALS (“back shop”) support currently being used. 16.251347 New Capability This scenario uses the same processes that are currently used when adding new capability to an I-level work center. The following will occur: a. The ICRL will be updated with the CAGE/PARTNO and D-level work center code b. If multiple work centers repair the same part, such as

I-level and D-level work centers,, the “Prime W/C” block will be used. c. Once inducted, the D-level work center will go in work, order parts (as required) and RFI the component. NOTE: All parts required by an artisan to accomplish the repair must be ordered with a D-level work center and identified as a failed part (indexed) on the MAF. 16.251348 New Capability Documentation Procedures The following explains documentation: a. JASU performs ICRL screening and adds the new component to the D-level work center’s ICRL b. If capability does not exist in ICRL, enter appropriate D-level work center and put a check in the “ICRL Ovrd” box. c. The above action will generate an ICRL error notice Double click on the Cage/Part Number line to open next screen. d. Click the “Add” button e. The “Prime WC” box allows multiple work centers to show repair capability for the same component. If the work center listed in the work center box is the primary repair work center, put a check

in the “Prime WC” box. If not, leave blank f. The MAF is assigned to the D-level work center by Production Control The D-level work center goes in work, orders parts (as required), and RFIs the component. If the artisan is a CSS, the ETS block must be checked. NOTES: 1. All parts required by an artisan to accomplish the repair must be ordered with a D-level work center and identified as a failed part (indexed) on the MAF. 2. Maintenance level on the MAF in OIMA NALCOMIS can not be changed without using the contingency methods. 3. The ICRL in OIMA NALCOMIS supports the identification of multiple like items in ICRL with different work centers and capabilities. The ICRL accepts multiple listings of the same CAGE and PARTNO combination by using the “Prime W/C” block. Either I-level or D-level will be the primary with a “Y” in this block. The other work center will have an “N” in this block. 4. The ETS block is a “check” box only A check in this block signifies that the

hours on the MAF are from a CSS. 16-127 COMNAVAIRFORINST 4790.2C 15 Jan 2017 5. Minimal training should be required for I-level technicians D-level artisans will require OIMA NALCOMIS training and access. 16.251349 D-Level Assist A component is inducted by JASU into an I-level or D-level work center. During the repair, assistance is required. Regardless of the maintenance level required for the assist, an assist MAF will be initiated using existing O-level or I-level NALCOMIS assist MAF procedures. This applies when repairable parts are not required. Examples include, but are not limited to: NDI, 2M repairs, welding, etc NOTE: By definition, a 2M artisan is unable to determine if an item is RFI until the item is tested using an approved procedure defined in NAVAIR approved publications, therefore, 2M Artisan procedures are the same as I-level 2M procedures. Specifically, the original work center will order required parts and forward, with SRA (circuit card assembly, etc.) and an

assist MAF to the D-level 2M artisan. Once the required repair is complete, the SRA (circuit card assembly) will be forwarded back to the original work center to verify RFI status. 16-128 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SUFFIX LOGIC TABLE DOES THE REPAIRABLE SUBASSEMBLY HAVE REPAIRABLE SUB-SUBASSEMBLIES? IF NO, ASSIGN: (Note 1) 1A 1B 1C . . . . . . . . . . . . . . . . 2A 2B . . . . . 9A . . . . . 9Z (216 total) IF YES, ASSIGN: SUFFIX ASSIGNED TO SUB-SUBASSEMBLIES? (Note 1) (Note 1) A B C D E F G H J K L . . . . . . . . . . . . . . . . . . . . . Z (24 total) AA, AB, AC, BA, BB, BC CA, CB, CC DA, DB, DC, EA, EB, EC, FA, FB, FC, GA, GB, GC AZ (24 total) BZ (24 total) CZ (24 total) DZ EZ (Note 2) FZ GZ (576 total) NOTES 1. Alphabetic I and O are not used. Numeric 1 is used, but 0 is not 2. If more than 24 double suffix JCNs are required, use suffixes from the next available suffix letter. For example, if suffix letters A through G have been used and more suffixes are

required for JCNs with suffixes beginning with E, the next available letter, H, would be used. Continue JCN assignment with HA, HB, HV, and so on. Figure 16-1: JCN Suffix Logic Table 16-129 COMNAVAIRFORINST 4790.2C 15 Jan 2017 EXAMPLE OF JCN SUFFIX SELECTION REPAIRABLE COMPONENT REMOVED AND REPAIRED ON JCN XYZ 234 487. XYZ 234 487 1A 1st REPAIRABLE SUBASSEMBLY REMOVED HAS NO REPAIRABLE SUBSUBASSEMBLIES. JCN ASSIGNED: XYZ 234 487 1A. 1B 2nd REPAIRABLE SUBASSEMBLY REMOVED HAS NO REPAIRABLE SUBSUBASSEMBLIES. JCN ASSIGNED: XYZ 234 487 1B. 3rd REPAIRABLE SUBASSEMBLY REMOVED HAS REPAIRABLE SUB-SUBASSEMBLIES. JCN ASSIGNED: XYZ 234 487A. A 1st REPAIRABLE SUBSUBASSEMBLY REMOVED IS ASSIGNED JCN: XYZ 234 487 AA. AA AB 2nd REPAIRABLE SUBSUBASSEMBLY REMOVED IS ASSIGNED JCN: XYZ 234 487 AB. THE NEXT REPAIRABLE SUBASSEMBLY REMOVED HAVING NO REPAIRABLE SUBSUBASSEMBLIES WOULD BE ASSIGNED JCN XYZ 234 487 1C. THE NEXT REPAIRABLE SUBASSEMBLY REMOVED HAVING REPAIRABLE SUBSUBASSEMBLIES

WOULD BE ASSIGNED JCN XYZ 234 487 B. Figure 16-2: Example of JCN Suffix Selection 16-130 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2S21601 N211 *WORKLOAD INQ 18 FEB 97 (97049) ENTER DATA FOR ONE OPTION 1. WORK CENTER 2. WORK CENTER WUC WC WUC MCN 41M 41M 41M 41M 41M 41M 0300900 0300900 0300900 0300900 0300900 0300900 A9BSJGP 0240228 0240227 A9BRLCB A9BREZN A9BSJGE JCN BF0309A00 AL1287A00 B10301B00 BF0252A00 B10235A00 B10308A00 TOTAL OUTSTANDING MAFS BY PRIORITY FOR WC 1. 00000 2. 00000 WORK PRI POOL TYPE MGMT CD OWED ORG 3 3 3 3 3 3 SYSTEM REASON 900 HR INSP 900 HR 281636 900 HR 282083 900 HR INSP 900 HR 900 HR INSP 3. 00006 4. 00000 Figure 16-3: Workload Inquiry 16-131 EQUIP STATJS DATE TIME M8 M8 M8 M8 M8 M8 96323 96323 96323 96323 96314 96320 2030 2030 2030 1330 1713 1430 COMNAVAIRFORINST 4790.2C 15 Jan 2017 MSG DATA ANALYST QA AMSU INDUCTION INITIATION PC APPROVAL MAF UPDATE CDI SUPERVISOR HARDCOPY MAF PC REVIEW HARDCOPY MAF Figure 16-4:

Off-Equipment Documentation Flow 16-132 LOGS/ RECORDS HARDCOPY MAF COMNAVAIRFORINST 4790.2C 15 Jan 2017 SE INVENTORY GAIN DISCREPANCY MAF INITIATION MSG DATA ANALYST QA PC APPROVAL MAF UPDATE CDI SUPERVISOR PC REVIEW HARDCOPY MAF HARDCOPY MAF Figure 16-5: On-Equipment Work Initiated by I-level Documentation Flow 16-133 LOGS/ RECORDS HARDCOPY MAF COMNAVAIRFORINST 4790.2C 15 Jan 2017 W ARNING: Unauthorized persons removing defacing, or destroying this tag may be subject to a fine of not more than $1,000 or imprisonment for not more than one year or both. (18USC 1361) INSPECTION ACTIVITY A 9B 7RH 1560-00-123-4567PF 215-04123-1 VALVE SERIAL NUMBER/LOT NUMBER 0123 REASON FOR REPAIRABLE CONDITION BCM -1 UNIT OF ISSUE REMOVED FROM EA INSPECTORS NAME OR STAMP AND DATE CONTRACT OR PURCHASE ORDER NO. QUANTITY 1 SSGT GOTT 96285 REMARKS AAFF PD4-123-456 Figure 16-6: Unserviceable Label-Material (DD 1577-2) 16-134 CONDITION CODE F DD F o r m 1577-2

(10/66) S/N 0102- LF-016-0000 UNSERVICEABLE (REPAIRABLE) TAG -MATERIAL FSN, PART NO. AND ITEM DESCRIPTION COMNAVAIRFORINST 4790.2C 15 Jan 2017 ISSUE/RECEIPT INVENTORY AND LOCATOR 1 2 I N V E N T O R Y L O C A T O R C A R D T A B 1 I N V E N T O R Y C A R D 2 1 2 1 2 1 L O C A T O R I N V E N T O R Y L O C A T O R I N V E N T O R Y L O C A T O R I N V E N T O R Y T A B C A R D T A B C A R D T A B NOTE: This board will be used for issue/receipt inventory and locator only. Figure 16-7: IRIL Board 16-135 C A R D 2 L O C A T O R T A B COMNAVAIRFORINST 4790.2C 15 Jan 2017 Fold on dotted line TEC MODEL SERIAL OWNER NOTE: The pocket indicator strip is a method of visually identifying each accountable item of SE displayed on the VIDS board. This indicator strip will show the TEC, model, serial number, and owner of each piece of equipment in custody. RED VR-56 BLUE VFA-103 NOTE: Locator tabs are locally produced and are color coded or indexed to

indicate the physical location of the equipment IMAs supporting large numbers of squadrons may prefer to index the locator tabs rather than color code. Figure 16-8: Pocket Indicator Strips and Locator Tabs 16-136 GREEN VFA-34 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SE Transfer Report Part I SERNO 5MH259 TEC = "GPC7" AND BUNO/SERNO = "5MH259" AND COMPLETION DATE BETWEEN "09/01/1997" AND "08/31/1997" TRANS MAL JCN W/C SYSTEM REASON WUC CD MI WD TM AT MCN C9CAAR8 C9CAFM9 C9CATY1 C9C094011 C9C100A00 C9C114A00 980 950 950 T/T TT259 14 DAY TT259 PM 23BX400 030000A 030000A 11 11 11 1 1 1 C O O B P P 320 000 000 C 0 0 IP MAN HRS EMT HRS SE METER COMP DATE 1 1 1 0.7 2.0 8.0 0.7 1.0 4.0 A0000 M0000 M0000 97094 97101 97115 SE Transfer Report Part 2 SERNO 5MH259 TEC = "GPC7" AND BUNO/SERNO = "5MH259" AND COMPLETION DATE BETWEEN "09/01/1997" AND "08/31/1997" WORKER QA/CDI SUPER SIGN SIGN SIGN

DISCREPANCY MCN C9CAAR8 C9CAFM9 C9CATY1 CTFOX B EVANS B EVANS REBROWN LGGRANADOS LGGRANADOS DJRABCHENUK LGGRANADOS LGGRANADOS CORR ACTION UNIT HAS NO BRAKES C/W 14 DAY STEERING GEARBOX C/W 14 DAY STEERING GEARBOX BLED AIR FROM COMPRESSOR C/W 14 DAY TORQUE STEERING GE C/W 14 DAY STEERING GEARBOX T SE Transfer Report Part 3 SERNO 5MH259 MCN C9CBQX8 C9CCAZ8 C9CCVY1 TEC = "GPC7" AND BUNO/SERNO = "5MH259" AND TRANS CD = "23" AND COMPLETION DATE BETWEEN "09/01/1997" AND "08/31/1997" REMOV REMOV REMOV INSTALL JCN W/C SYSTEM REASON AT MAL CAGE P/N SERNO CAGE C9C137004 C9C147003 C9C165018 980 910 980 FLAT TIRE TIRE WORN R/F TIRE R R R 787 787 787 96906 29510 29510 GPC7/750X1 HA1321 HA1321 0 0 0 96906 29510 29510 INSTALL P/N INSTALL SERNO GPC7/750X1 HA1321 HA1321 0 0 0 SE Transfer Report Part 4 SERNO 5MH259 TEC = "GPC7" AND BUNO/SERNO = "5MH259" AND (TRANS CD = "23" OR TRANS CODE =

"12" AND COMPLETION DATE BETWEEN "09/01/1997" AND "08/31/1997" F/P IND MCN JCN W/C SYSTEM REASON WUC C9CBQX8 C9CCAZ8 C9CCVY1 C9C137004 C9C147003 C9C165018 980 910 980 FLAT TIRE TIRE WORN R/F TIRE 23BX330 23BX900 23BX900 AT MAL QTY CAGE FAILED P/N 96906 29510 29510 GPC7/750X16-IN 1 1 HA1321 1 HA1321 SE Transfer Report Part 5 SERNO 5MH259 TEC = "GPC7" AND BUNO/SERNO = "5MH259" AND TRANS CD = "41" AND COMPLETION DATE BETWEEN "09/01/1997" AND "08/31/1997" MCN JCN W/C C9CSS75 C9C311111 910 TD INT TD CODE TD BASIC 62 4124 TD REV TD AM TD PART TD KIT A1 Figure 16-9: SE Transfer Report (Sample) 16-137 ORD DATE 97137 97147 97165 DDSN RCPT DATE COMNAVAIRFORINST 4790.2C 15 Jan 2017 (1) WC & EQUIP (2) (3) SE QTY (4) LRCA LIMITS HI LOW (5) P R I (6) (7) (8) (9) AWM IN WORK AWP COMPLETED 610 6217100 62172 6528100 620 7343100 7351100 640 76240 76290 76310

Figure 16-10: VIDS Board Layout 16-138 COMNAVAIRFORINST 4790.2C 15 Jan 2017 SSC PRODUCTION CONTROL IMA - AMSU 1 WORK CENTER 1 1 2 2 4 4 5 1. Receives component for delive r y to A I MD , f or w a r ds c ompo nent with Copies 1, 2, 3, 4, and 5 attached to the IMA AMSU. 1 5 on board 4 5 3. Schedules item and ins e r ts Co p y 3 o n th e V I D S board. 3 2. Receives component, inserts date received in Block B08 and work center in Block A19. Forwards Copy 3 to Production Control and returns Copy 2 to SSC. 1 4 4 3 3 MATERIAL CONTROL WORKER 4. Receives component with Copies 1, 4, and 5 a tta c he d, inse r ts Copy 5 on the VIDS board. 5 on board 2 Condition Tag 1 4 Upon receipt of Copy 2, file. 1 4 Condition Tag 3 1 4 9. Receives component with Copy 4 and Material Condition Tag attached. Signs Copy 1. 8. Notifies SSC that component is ready for turn-in Removes and obtains SSC signature on Copy 1. 11. Records necessary data, verifies Copy 3, holds Copy 3 in

suspense file until Copy 1 is returned from QA/A. 1 7. Screens and signs the VIDS/MAF. Turns component over to AMSU with Copies 1, 4, a nd Ma te r ia l Cond i t i o n T a g a t t a c h e d. Retains Copy 5 for MDR verification 5 1 10. Returns Copy 1 to production control 1 12. Filed Figure 16-11: Off-Equipment VIDS/MAF Flow 16-139 5 . A s s i g n e d j o b, completes action and VIDS/MAF. C o m p l e t e s M a t eerial Condition Tag and attaches to component. Returns VIDS/MAF to supervisor for screening and completion of maintenance data . To QA/A From QA/A 6. Requisition parts if necessary. Completes necessary data on the VIDS/MAF. COMNAVAIRFORINST 4790.2C 15 Jan 2017 VIDS/M AF 1 On-Equipment (End Item) VIDS/MAF 1 * ON-EQUIPM ENT WORK. A VIDS/M AF is generated for all work performed on an end item . of SE. If no repairable component is removed, this is the only document required JCN : XYZ123 456 VIDS/M AF 2 Turn-In (Component) * VIDS/MAF 2 TURN-IN DOCUM ENT. A

VIDS/M AF is generated whenever a repairable component is removed from an end item for off-equipment work. A turn-in document will have the same JCN as the removal document, and will be submitted to AM SU. JCN : XYZ 123 456 VIDS/M AF 2a Off-Equipment (Component) * VIDS/MAF 2a OFF-EQUIPM ENT. Complete the maintenance action on the removed component by completing - If no repairable subassemblies are removed, this is the last document required. the turn-in document. JCN : XYZ123 456 VIDS/M AF 3 Suffix Turn-In (Subassembly) VIDS/MAF 3 * SUFFIX TURN-IN . A VIDS/M AF is generated for each repairable subassembly removed from component during off-equipment work. A suffix VIDS/M AF will have a suffix of the original . JCN JCN : XYZ 123 456A VIDS/M AF 3a Off-Equipment (Subassembly) * VIDS/MAF 3a OFF-EQUIPM ENT. Complete the maintenance action on a removed subassembly by completing the suffix turn-in - document. If no repairable sub-subassembly is removed, this is the last document

required. JCN : XYZ 123 456A NOTE: If a repairable sub-subassembly is removed from a subassembly, repeat the procedures shown in VIDS/M AF 3 and VIDS/M AF 3a. - Figure 16-12: Types of VIDS/MAFs Used for SE, Training Devices, and Missile Target Documentation 16-140 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JHTRACY 1 D9891A7 JBS 96020 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 1 C 105 01 1.5 1.5 48KAE10 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GBGB 460640 D B S0691

REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96020 1500 IN WORK 96020 1500 96020 1630 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96020 1500 DISCREPANCY THERMOCOUPLE LEADS ARE PILOT/INITIATOR IW 96020 1500 JC 96020 1630 LOOSE AN STEELE CORRECTIVE ACTION TIGHTENED LOOSE LEADS CF QA REQ REQ CORRECTED BY JHTRACY INSPECTED BY IMWILSON JOB CONTROL NUMBER ORG DAY SER SUF D98020099 WORK CENTER 91A SUPERVISOR JBSMITH STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN AIR START SWP4826 Figure 16-13: End Item Repair (No Removed Component) 16-141 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE

TRACY 1 D9891A4 KLD 96332 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.9 96332 1045 3 2.8 LOCAL USE REFERENCE INDEX F/P AWP H A/T 0 FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PDCA1 000 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC 00000 48P206 E0360 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 48KA1N0 D98 12 1 C 127 01 0.9 0.9 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GBGB CYP138 C B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 1045 96332 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1330 IN WORK 96332 1425 96332 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 2.8 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96332 1045 DISCREPANCY LOAD CONTROL VALVE STAYS PILOT/INITIATOR 96332 1330 IW 96332 1425 JC

OPEN LT DEAN CORRECTIVE ACTION ADJUSTED LOAD CONTROL VALVE AND THERMOSTAT CORRECTED BY JHTRACY JOB CONTROL NUMBER ORG DAY SER SUF D98332496 INSPECTED BY IMWILSON WORK CENTER 91A CF QA REQ REQ SUPERVISOR JBSMITH STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN HUFFER SWP4826 Figure 16-14: End Item Repair of a SEGTE (No Removed Component) 16-142 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE NERI 1 D9865Q7 SWP 96129 HARRIS 1 D9865Q4 SWP 96129 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 96129 0700 3 1.0 1.5 LOCAL USE REFERENCE INDEX F/P FSCM AWP A/T 77327 FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 BK0 247AS20-100-005 03 DATE ORD 96129 REQ NO 6129D911 DATE REC 96129 WORK ACT MAL TECHNICAL

DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 23 1 R 064 01 2.5 2.5 78HP800 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M1111 GVAB 000060 C B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0700 96129 0800 77327 1002 77327 005 IN WORK 96129 1200 96129 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS20-100-005 96129 247AS20-100-005 M3 1.0 TIME/CYCLES TIME/CYCLES M7626 M2772 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES W8000 W8000 X0129 X0111 STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96129 0700 DISCREPANCY BB20 FAILS MODULATION TEST PILOT/INITIATOR 96129 0800 IW 96129 0900 WP AEC CREWS 96129 1030 IW JC 96129 1200 CORRECTIVE ACTION R & R BB20. TESTS GOOD CF QA REQ REQ CORRECTED BY JHHARRIS INSPECTED BY IBSMITH JOB CONTROL NUMBER ORG DAY SER SUF D98129456 WORK CENTER 65Q SUPERVISOR IMLOGAN STATUS DOWN

INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN BB20 SWP4826 Figure 16-15: End Item Repair (Removed Repairable Component) 16-143 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DUNN/WRIGHT 1 D9892A6 RIM 96198 DUNN/WRIGHT 1 D9892A2 RIM 96199 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 6.0 96198 1110 8 25.2 6.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 11 1 S 800 01 12.0 6.0 12DCF TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M0123 GECB 014009 O B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM

INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0810 96198 0810 IN WORK 96198 1520 96199 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M8 25.2 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0810 DISCREPANCY REMOVE REFRIGERATION DUCTING PILOT/INITIATOR 96198 0810 IW 96198 1110 M8 FOR W/C 970. REINSTALL WHEN NOTIFIED AEC LEMPICKI 96199 1220 IW JC 96199 1520 CORRECTIVE ACTION R & R DUCTING CF QA REQ REQ CORRECTED BY JHDUNN JOB CONTROL NUMBER ORG DAY SER SUF D98198420 INSPECTED BY MMLONG WORK CENTER 92A SUPERVISOR RIMILLER STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN AIR COND SWP4826 Figure 16-16: Facilitate Other Maintenance Action 16-144 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN

NAME/SHIFT TOOLBOX/INT DATE TRACY/LALLY 1 D989704 SWS 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 6.0 96198 0800 3 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 12DCH D98 11 1 B 037 01 6.0 3.0 TYPE BU/SER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD EQUIP NUMBER GECB 014009 C B M0123 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0800 0800 IN WORK 96198 96198 1200 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 1.0 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0800 DISCREPANCY EVAPORATOR WORKS PILOT/INITIATOR IW 96198 0900 JC 96198 1200

INTERMITTENTLY AMCS KOVICH CORRECTIVE ACTION REPAIRED LOOSE CONTROL BRACKET CF QA REQ REQ CORRECTED BY JHTRACY JOB CONTROL NUMBER ORG DAY SER SUF D98198419 INSPECTED BY IMWILSON WORK CENTER 970 SUPERVISOR JBSMITH STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN AIR COND SWP4826 Figure 16-17: Primary Work Center Repair Action 16-145 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE TRACY 1 D9892A2 SWJ 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.5 96198 0800 3 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 12DCH D98 11

1 B 037 00 2.5 2.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GECB 014009 V B M0123 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 96198 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0900 IN WORK 96198 96198 1130 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 1.5 TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96198 0800 DISCREPANCY ASSIST W/C 970 (EVAP IW 96198 0900 JC 96198 1130 INTERMITTENT) TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AT2 DEAN CORRECTIVE ACTION ASSISTED IN REPAIR OF LOOSE BRACKET CF QA REQ REQ CORRECTED BY JHTRACY JOB CONTROL NUMBER ORG DAY SER SUF D98198419 INSPECTED BY IMWILSON WORK CENTER 92A SUPERVISOR JBSMITH STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN AIR COND SWP4826 Figure 16-18: Assisting Work Centers (Same WUC) 16-146 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN

SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X LLEMBACH ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE TRACY 1 D989304 KLD 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 12DCD D98 11 1 Z C01 01 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GECB 014009 V B M0123 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0830 0830 IN WORK 96198 96198 1030 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 1.5 TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96198 0830 DISCREPANCY

ASSIST W/C 970 (EVAP IW 96198 0830 JC 96198 1030 INTERMITTENT) TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AT2 DEAN CORRECTIVE ACTION REMOVED CORROSION FROM POWER TAKE OFF CONNECTOR TERMINAL. CORRECTED BY JHTRACY JOB CONTROL NUMBER ORG DAY SER SUF D98198419 INSPECTED BY IMWILSON WORK CENTER 930 SUPERVISOR JBSMITH STATUS DOWN INSPT JCN CF QA REQ REQ MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN AIR COND SWP4826 Figure 16-19: Assisting Work Centers (Different WUC) 16-147 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JHASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE HOYA 1 D989304 R/S 96198 HOYA 1 D989304 R/S 96199 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 1.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 94990 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001

8RV3006 BK0 02 DATE ORD 96198 REQ NO 6198D114 DATE REC 96199 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 44FM820 D98 18 1 T 814 01 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GAC6 263755 O B M3144 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0800 0800 94990 12949 94990 12887 IN WORK 96198 96199 1000 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 8RV3006 96198 8RV3006 TIME/CYCLES TIME/CYCLES A0000 A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0800 DISCREPANCY REMOVE VOLTAGE REGULATOR PILOT/INITIATOR IW 96198 0800 WP 96198 0900 FOR #263730 AS1 SMITH IW 96199 0900 IW 96199 1000 CORRECTIVE ACTION REMOVED AND REPLACED REGULATOR CF QA REQ REQ CORRECTED BY JHHOYA JOB CONTROL NUMBER ORG DAY SER SUF D98198012 INSPECTED BY

IBSMITH WORK CENTER 930 SUPERVISOR RISILVER STATUS DOWN INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 1 Figure 16-20: On-Equipment Cannibalization 16-148 RFI BCM SYSTEM/REASON MCN VOLT REG SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI A/T FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 030000B TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GLCA AE4999 O P A0000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER IN WORK COMP DATE

AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY PERFORM 4 WEEK PM INSP NEXT INSP DUE 96228. POC VF-102 AMS1 KING EXT 4255 PILOT/INITIATOR AS2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AE4200C00 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN BCM SYSTEM/REASON MCN 4 WEEK INSP SWP4826 Figure 16-21: Support Equipment Turned-In by a Supported Activity for Scheduled Maintenance (Excluding TMDE) 16-149 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI A/T FSCM PART

NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31EL000 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD A0000 GLCA AE4999 C B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY JACK RAM LEAKING. POC VF-102 AMH1 KING EXT 2455. PILOT/INITIATOR AS2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AE4200545 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN BCM SYSTEM/REASON MCN JACK RAM LK SWP4826 Figure 16-22: Support Equipment Turned-In by a Supported Activity for

Unscheduled Maintenance (Excluding TMDE) 149 16-150 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 78HPY00 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GVAB 000060 C B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 77327 005 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS20-100-005 96129 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96129 1000 TIME/CYCLES

TIME/CYCLES TIME/CYCLES DISCREPANCY M7626 W8000 X0129 TIME/CYCLES TIME/CYCLES TIME/CYCLES BB20 FAILS MODULATION TEST PILOT/INITIATOR AEC CWERS CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D98129456 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6129D911 SYSTEM/REASON MCN BB20 FAILURE SWP4826 Figure 16-23: Turn-In Document (Off-Equipment Repair) 16-151 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI A/T FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT

48KA100 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD PDCA 7P2932 F B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96247 PDCA1 7P2932 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96247 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96247 0745 E7981 TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY TEETH BROKEN OFF STARTER GEAR SHAFT. //NOTE: INSP JCN AUTO ASSIGNED//// PILOT/INITIATOR AS2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D98247911 WORK CENTER STATUS INSPT JCN B00 PRI TURN-IN DDSN 6247D123 SYSTEM/REASON MCN STARTER SWP4826 Figure 16-24: Turn-In Document SEGTE Repair 16-152 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS

REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE AYERS 1 D9865Q3 SWP 96129 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 96129 1100 3 1.0 LOCAL USE REFERENCE INDEX H F/P AWP A/T X FSCM 77327 R FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 20A1A40 064 00001 BK1 PART NUMBER 247AS20-244-001 FSCM PART NUMBER FSCM PART NUMBER 03 DATE ORD REQ NO 6129D511 96129 DATE REC 96129 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 064 01 3.0 3.0 78HP800 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GVAB 000060 C B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1000 96129 1200 77327 005 IN WORK 96129 1500 96129 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS20-100-005 96129 M3 1.0 TIME/CYCLES TIME/CYCLES M7626 MAINTENANCE/SUPPLY REC TIME/CYCLES

TIME/CYCLES W8000 X0129 STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96129 1000 DISCREPANCY BB20 FAILS MODULATION TEST PILOT/INITIATOR 96129 1100 M3 96129 1200 IW AS2 SMITH 96129 1500 JC CORRECTIVE ACTION R & R 20A1A40. CHECKS GOOD CORRECTED BY JHAYERS INSPECTED BY IBSMITH JOB CONTROL NUMBER ORG DAY SER SUF D98129456 WORK CENTER 65Q SUPERVISOR IMLOGAN STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 1 6129D911 SYSTEM/REASON MCN BB20 SWP4826 Figure 16-25: Off-Equipment Component Repair 16-153 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL

TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 78HPY27 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GVAB 000060 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1215 96129 77327 0031 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS20-244-001 96129 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96129 1215 TIME/CYCLES TIME/CYCLES TIME/CYCLES M3500 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY BB20 20A1A40 CAUSES MODULATION TEST TO FAIL PILOT/INITIATOR AS2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D98129456A WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6129D511 Figure 16-26: Suffix Turn-In Document 16-154 BCM SYSTEM/REASON MCN BB20 FAILURE SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502

MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RICH 1 D986902 SWP 96130 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96130 1100 3 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X FSCM 77327 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI A40Z1 R 064 00001 BK1 PART NUMBER 247AS20-400-002 FSCM PART NUMBER FSCM PART NUMBER 03 DATE ORD REQ NO 6130D661 96130 DATE REC 96130 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 78HPY27 D98 32 2 C 064 01 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GVAB 000060 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96129 1215 1215 77327 0031 IN WORK 96129 96130 1400 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3

247AS20-244-001 96129 1.0 TIME/CYCLES TIME/CYCLES M3500 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96129 1215 DISCREPANCY BB20 20A1A40 CAUSES PILOT/INITIATOR M3 96129 1100 IW 96129 1200 MODULATION TEST TO FAIL AE2 SMITH JC 96129 1400 CORRECTIVE ACTION R & R A40Z1. CHECKS GOOD CORRECTED BY TTRICH JOB CONTROL NUMBER ORG DAY SER SUF D98129456A INSPECTED BY IBSMITH WORK CENTER 690 SUPERVISOR IMLOGAN STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6129G511 SYSTEM/REASON MCN BB20 SWP4826 Figure 16-27: Off-Equipment Subassembly Repair 16-155 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X TNBOLYARD ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI

FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 030000L D98 11 1 0 000 01 0.0 0.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GPDB 003145 O P M4687 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0800 0800 IN WORK 96198 96198 1400 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0800 DISCREPANCY COMPLY WITH MRCS FOR 250 HR PILOT/INITIATOR IW 96198 0800 JC 96198 1400 AM1 ROBINSON INSPECTION CORRECTIVE ACTION COMPLETED MRCS. CF QA REQ REQ CORRECTED BY JHROSS JOB CONTROL NUMBER ORG DAY SER SUF D98198A00 INSPECTED BY KRJOE WORK CENTER 950 SUPERVISOR KRJOE STATUS DOWN INSPT JCN MAINT CONTROL

IBMERCER PRI TURN-IN DDSN 1 Figure 16-28: Inspection Control Document 16-156 RFI BCM SYSTEM/REASON MCN 250 HR INSP SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X TNBOLYARD ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JHROSS 1 D989202 JBS 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 96198 1000 3 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 030000L D98 11 1 0 000 00 1.0 1.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GPDB 003145 O P M4687 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 1000 1300 IN

WORK 96198 96198 1400 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 1000 DISCREPANCY COMPLY WITH MRCS 7, 9, & 14 PILOT/INITIATOR IW 96198 1300 JC 96198 1400 AZ2 STEELE CORRECTIVE ACTION COMPLETED CARDS 7, 9, & 14. CF QA REQ REQ CORRECTED BY JHROSS INSPECTED BY KRJOE JOB CONTROL NUMBER ORG DAY SER SUF D98198A00 WORK CENTER 920 SUPERVISOR KRJOE STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN PM INSP SWP4826 Figure 16-29: Inspection Look Phase Supporting Document 16-157 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X TNBOLYARD ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE REED/TAYLOR 1 D989103 KLD 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 LOCAL USE REFERENCE

INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 00001 FSCM 92679 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER BK0 03 DATE ORD 96198 REQ NO 6198D113 DATE REC 96198 113120 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 23 1 R 135 01 4.0 2.0 48HX8L0 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M4826 GPDB 003145 M P REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1100 96198 1100 92679 106111 92679 106279 IN WORK 96198 1300 96198 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1113120 96198 1113120 TIME/CYCLES TIME/CYCLES A0000 A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 1100 DISCREPANCY STARTER NOISY AND DRAGGING PILOT/INITIATOR 96198 1100 IW 96198 1300 JC AS1 SMITH CORRECTIVE ACTION R & R

STARTER. CF QA REQ REQ CORRECTED BY JHREED JOB CONTROL NUMBER ORG DAY SER SUF D98198A02 INSPECTED BY IBSMITH WORK CENTER 910 SUPERVISOR RESILVER STATUS DOWN INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 1 Figure 16-30: Inspection Fix Phase Document 16-158 RFI BCM SYSTEM/REASON MCN STARTER SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X TNBOLYARD ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DAVIS 1 D989302 THT 96059 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 30003 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 ZO9 2345LKA128750SX 06 DATE ORD 96055 REQ NO 6055D912 DATE REC 96059 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 62 2345 A1 41 1 C 01 1.0 1.0 44FM820 D98

TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M1234 GAC6 261163 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1030 96055 1030 IN WORK 96055 1100 96059 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96055 1030 DISCREPANCY INCORPORATE SEC 2345 PILOT/INITIATOR 96055 1030 IW 96055 1030 WP AMCS KOVICH 96059 1000 IW JC 96059 1100 CORRECTIVE ACTION INCORPORATE SEC 2345 CF QA REQ REQ CORRECTED BY JHDAVIS INSPECTED BY IMJONES JOB CONTROL NUMBER ORG DAY SER SUF D98055965 WORK CENTER 930 SUPERVISOR JBLOWE STATUS UP INSPT JCN MAINT CONTROL MTMCKEEN PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN SEC 2345 SWP4826 Figure 16-31: End Item TD Compliance (No Removal Component) 16-159 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-32: TD Compliance

Supporting VIDS/MAF 16-160 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 15EE6 62 0023 00 47 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YGAA 001063 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 82598 1063 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267 96198 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES A0000 TIME/CYCLES

TIME/CYCLES TIME/CYCLES DISCREPANCY INCORPORATE SEC 23 IN PRESSURE REGULATOR PILOT/INITIATOR AS3 CREWS CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D98198111 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN SEC 23 SWP4826 Figure 16-33: TD Compliance Turn-In Document 16-161 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE WEST 1 D989405 KLD 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 62 0023 00 D98 47 2 C 01 1.0

1.0 15EE6 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YGAA 001063 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96198 0800 82598 1063 82598 1063 IN WORK 96198 0900 96198 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267 96198 1267-1 TIME/CYCLES A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96198 0800 DISCREPANCY INCORPORATE SEC 23 IN 96198 0800 IW 96198 0900 JC PRESSURE REGULATOR TIME/CYCLES TIME/CYCLES TIME/CYCLES A0000 PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION INCORPORATED SEC 23 CF QA REQ REQ CORRECTED BY DAWEST JOB CONTROL NUMBER ORG DAY SER SUF D98198111 INSPECTED BY GSKEYS WORK CENTER 940 SUPERVISOR GSKEYS STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN SEC 23 SWP4826 Figure 16-34: Off-Equipment TD Compliance Action 16-162 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502

MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X TNBOLYARD ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE FRYE 1 D989301 SWH 96270 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 62 2345 A1 41 1 Q 01 1.0 1.0 44FM820 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M1234 GAC6 261163 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1000 96270 1000 IN WORK 96270 1100 96270 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES

TIME/CYCLES M3 96270 1000 DISCREPANCY REMOVE SEC #2345 AS PER PILOT/INITIATOR 96270 1000 IW 96270 1100 JC NAVAIRSYSCOM MSG 270800Z SEP 93 BRINKMAN CORRECTIVE ACTION REMOVED SEC #2345 AS PER NAVAIRSYSCOM MSG 270800Z SEP 93 CORRECTED BY JHFRYE INSPECTED BY SWHILL JOB CONTROL NUMBER ORG DAY SER SUF D98270065 WORK CENTER 930 CF QA REQ REQ SUPERVISOR SWHILL STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN SEC2345 SWP4826 Figure 16-35: TD Compliance Removal (On-Equipment) 16-163 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 TD Compliance VIDS/M AF 1 On-Equipment (End Item) * TD COMPLIANCE VIDS/MAF 1 END ITEM TD COM PLIANCE. A TD compliance VIDS/M AF is generated for all TDs incorporated on an end item of SE. If no component is removed, this is the only document required JCN: XYZ 123 456 TD Compliance VIDS/M AF 2 Turn-In (Component) * TD COMPLIANCE VIDS/MAF 2 TD COM PLIANCE TURN-IN DOCUMENT. A TD compliance turn-in document is generated

whenever a component is removed for off-equipment inspection or modification in . compliance with an end item. JCN: XYZ 123 456 TD Compliance VIDS/M AF2a Off-Equipment (Component) * JCN: XYZ 123 456 A TD COMPLIANCE VIDS/MAF 2a OFF-EQUIPM ENT TO COM PLIANCE. Complete the assist offequipment portion of the end item TDs by completing the turn-in document. Figure 16-36: VIDS/MAF Required for End Item TD Compliance Concurrent with a Failed Part 16-164 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Supporting VIDS/M AF 1 On-Equipment (End Item) * SUPPORTING VIDS/MAF 1 COM PONENT TD COMPLIANCE. A TD compliance supporting VIDS/M AF is generated to account for onequipment work, whenever a RFI component is removed for off-equipment inspection or modification in compliance with a TD that applies only to the components. The TD compliance is not identified on the supporting VIDS/M AF . JCN: XYZ 123 567 TD Compliance VIDS/M AF 2 Turn-In (Component) * TD COMPLIANCE VIDS/MAF 2 TD COM PLIANCE

TURN-IN DOCUMENT. A TD compliance turn-in document is generated, whenever a component is removed for off-equipment inspection or modification in compliance with a TD that applies only to the component. . JCN: XYZ 123 567 TD Compliance VIDS/M AF 2a Off-Equipment (Component) TD COMPLIANCE VIDS/MAF 2a OFF-EQUIPM ENT TD COM PLIANCE. Complete the compliance portion of the component TD by completing the turn-in document. * JCN : XYZ 123 567 Figure 16-37: VIDS/MAF Required for Component TD Compliance 16-165 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Repair VIDS/M AF 1 On-Equipment (End Item) * REPAIR VIDS/MAF 1 ON-EQUIPM ENT WORK. A VIDSW/M AF is generated to document the end item failure and order a replacement component. M an-hours and EM T expended removing and replacing the component are accounted for on the TD compliance on-equipment VIDS/M AF (#3 below). JCN : XYZ 123 234 Repair VIDS/M AF 2 Turn-In (Component) REPAIR VIDS/MAF 2 TURN-IN DOCUM ENT. A turn-in document is generated

to initiate repair of the removed component This is in addition to the TD compliance turn-in document (#4 below). * JCN : XYZ 123 234 Repair VIDS/M AF 2a Off-Equipment (Component) * REPAIR VIDS/MAF 2a OFF-EQUIPM ENT REPAIR. Complete the repair action on the removed component by completing the turn-in document. JCN : XYZ 123 234 TD Compliance VIDS/M AF 3 On-Equipment (End Item) TD COMPLIANCE VIDS/MAF 3 END-ITEM TD COM PLIANCE. A TD compliance VIDS/M AF is generated to document the TD compliance on the end item. M an-hours and EM T expended for component removal will be documented on this VIDS/M AF * JCN : XYZ 123 235 TD Compliance VIDS/M AF 4 Turn-In (Component) * TD COM PLIANCE VIDS/M AF 4 TD COM PLIANCE TURN-IN DOCUMENT. A VIDS/M AF is generated to initiate the off-equipment portion of the end item TD compliance action. This is in addition to the repair turn-in document (#2 above). JCN : XYZ 123 235 TD Compliance VIDS/M AF 4a Off-Equipment (Component) * TD COMPLIANCE VIDS/MAF

4a OFF-EQUIPM ENT TD COM PLIANCE. Complete the assist (off-equipment) portion of the end item TD by completing the turn-in document. JCN : XYZ 123 235 Figure 16-38: VIDS/MAF Required for End Item TD Compliance Concurrent With a Failed Part 16-166 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Repair VIDS/M AF 1 On-Equipment (End Item) * REPAIR VIDS/MAF 1 ON-EQUIPM ENT WORK. When a TD applies to a component that is removed for failure, the M AF that documents the failure will also account for the man-hours and EM T expended removing and replacing the component. JCN : XYZ 123 456 Repair VIDS/M AF 2 Turn-In (Component) * REPAIR VIDS/MAF TURN-IN DOCUM ENT. A turn-in document is generated to initiate repair of the removed component This is in addition to the TD compliance turn-in document. JCN : XYZ 123 456 Repair VIDS/M AF 2a Off-Equipment (Component) * REPAIR VIDS/MAF 2a OFF-EQUIPM ENT REPAIR. Complete the repair action on the removed component by completing the turn-in document. JCN

: XYZ 123 456 TD Compliance VIDS/M AF 3 Turn-In (Component) TD COMPLIANCE VIDS/MAF 3 TD COM PLIANCE TURN-IN DOCUMENT. A VIDS/M AF is generated to initiate the off-equipment portion of the end item TD compliance action. This is in addition to the repair turn-in document (#2 above) * JCN : XYZ 123 457 TD Compliance VIDS/M AF 3a Off-Equipment (Component) * TD COMPLIANCE VIDS/MAF 3a OFF-EQUIPM ENT TD COM PLIANCE. Complete the compliance portion of the component TD by completing the turn-in document. JCN : XYZ 123 457 Figure 16-39: VIDS/MAF Required for Component TD Compliance With a Failed Part 16-167 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Repair MAF 1 On-Equipment (End Item) * REPAIR MAF 1 ON-EQUIPMENT WORK. When a TD applies to a component that is removed for failure, the MAF that documents the failure will also account for the man-hours and EMT expended removing and replacing the component. JCN: XYZ 123 456 Repair MAF 2 Turn-In (Component) * REPAIR MAF 2 TURN-IN DOCUMENT.

A turn-in document is generated to initiate repair of the removed component. This is in addition to the TD compliance turn-in document JCN: XYZ 123 456 Repair MAF 2a Off-Equipment (Component) * REPAIR MAF 2a OFF-EQUIPMENT REPAIR. Complete the repair action on the removed component by completing the turn-in document JCN: XYZ 123 456 TD Compliance MAF 3 Turn-In (Component) * TD COMPLIANCE MAF 3 TD COMPLIANCE TURN-IN DOCUMENT. A MAF is generated to initiate the off-equipment portion of the end item TD compliance action. This is in addition to the repair turn-in document (#2 above). JCN: XYZ 123 457 TD Compliance MAF 3a Off-Equipment (Component) * TD COMPLIANCE MAF 3a OFF-EQUIPMENT TD COMPLIANCE. Complete the compliance portion of the component TD by completing the turn-in document. JCN: XYZ 123 457 Figure 16-40: Inventory Transaction (Gain) 16-168 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE

LOGS REC X MLHAGAN ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 03 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M0100 0 GPMF PXF299 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER IN WORK 2400 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC JC 96027 2400 TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY PILOT/INITIATOR CORRECTIVE ACTION INVENTORY LOSS CF QA REQ REQ CORRECTED BY JOB CONTROL NUMBER ORG DAY SER SUF INSPECTED

BY WORK CENTER SUPERVISOR ICBUTLER STATUS INSPT JCN MAINT CONTROL PRI TURN-IN DDSN Figure 16-41: Inventory Transaction (Loss) 16-169 RFI BCM SYSTEM/REASON MCN SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE WHITE 1 D989104 HRD 96198 WHITE 1 D989104 HRD 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.5 96198 0900 8 6.5 0.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 19BC5 D98 11 1 S 804 01 1.0 1.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GDCD 001222 O P M1234 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM

INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0830 0830 IN WORK 96198 96198 1600 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0830 DISCREPANCY PRESSURE GAUGE 1641 DUE FOR PILOT/INITIATOR IW 96198 0830 M8 96198 0900 CALIBRATION AZ3 LLOYD IW 96198 1530 JC 96198 1600 CORRECTIVE ACTION R & R GAUGE 1641. CHECKED GOOD AT CAL LAB CF QA REQ REQ CORRECTED BY JHWHITE JOB CONTROL NUMBER ORG DAY SER SUF D98198217 INSPECTED BY IMLONG WORK CENTER 910 SUPERVISOR HRDRAPAL STATUS DOWN INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN GAUGE SWP4826 Figure 16-42: Removed Component for Calibration 16-170 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE

ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7336200 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 06481 AAM025 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 866542 96028 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY M0625 W1000 X0123 TIME/CYCLES TIME/CYCLES TIME/CYCLES ASQ-61 WILL NOT ZERO OUT PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF

AC3028009 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6028G112 Figure 16-43: Component Turn-In Document 16-171 BCM SYSTEM/REASON MCN ASQ-61 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 1 703 01 0.0 0.0 7363200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96028 0800 06481 AAM025 IN WORK 96028 0800 96028

COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 866542 96028 TIME/CYCLES TIME/CYCLES M0625 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES W1000 X0123 STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96028 0800 DISCREPANCY ASQ-61 WILL NOT ZERO OUT PILOT/INITIATOR 96028 0800 IW 96028 0800 JC AZ3 SMITH CORRECTIVE ACTION BEYOND CAPABILITY OF MAINTENANCE BCM-1 CORRECTED BY JOB CONTROL NUMBER ORG DAY SER SUF AC3028009 INSPECTED BY WORK CENTER 05A SUPERVISOR IMLOGAN STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6028G112 Figure 16-44: BCM Action (AMSU) 16-172 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN ASQ-61 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DAVIS 1 D9865A4 SWJ 96032 DAVIS 1 D9865A4 SWJ 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 6.0 96032 1700 3 15.0 4.5 96033

1230 3 19.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 39 2 Y 160 01 10.5 105 7363200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158589 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1100 96032 1100 IN WORK 96032 0800 96034 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 34.5 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96032 1100 DISCREPANCY ASQ-61 WILL NOT ZERO OUT PILOT/INITIATOR 96032 1100 IW 96032 1700 M3 AT1 DEAN 96033 0800 IW M3 96033 1230 CORRECTIVE ACTION CLOSE OUT TROUBLESHOOTING IW 96034 0800 JC 96034 0800 CF QA REQ

REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI BCM JBSMITH IBMERCER JOB CONTROL NUMBER ORG DAY SER SUF AC3032009 WORK CENTER 65A STATUS INSPT JCN PRI TURN-IN DDSN 3 Figure 16-45: Troubleshooting Close Out 16-173 SYSTEM/REASON MCN ASQ-61 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BENDER 1 D9851A4 SWP 96028 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7336200 D98 11 2 C 780 00 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 V B REPAIR CYCLE

DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96028 0830 0830 IN WORK 96028 96028 1030 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96028 0830 DISCREPANCY CHASSIS BENT AND REQUIRES POP PILOT/INITIATOR IW 96028 0830 JC 96028 1030 RIVETS (MOUNTING BRACKETS) AIRFRAME ASSIST AM2 DEAN CORRECTIVE ACTION STRAIGHTENED AND STRENGTHED LOWER MOUNTING BRACKET CORRECTED BY JHBENDER JOB CONTROL NUMBER ORG DAY SER SUF AC3028009 INSPECTED BY BNPOWELL WORK CENTER 51A CF QA REQ REQ SUPERVISOR JBTALLEY STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN BRACKET SWP4826 Figure 16-46: Assisting Work Center (Same WUC) 16-174 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES

ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE FORD 1 D989403 SWJ 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 12DCD D98 11 2 Z C01 01 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GECB 014009 V B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0830 0830 IN WORK 96198 96198 1030 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96198 0830 DISCREPANCY ASSIST W/C 970 (EVAP IW 96198 0830 JC 96198 1030 INTERMITTENT) TIME/CYCLES TIME/CYCLES TIME/CYCLES

PILOT/INITIATOR AS3 DEAN CORRECTIVE ACTION REMOVED CORROSION FROM POWER TAKE OFF CONNECTOR TERMINAL CORRECTED BY JHFORD JOB CONTROL NUMBER ORG DAY SER SUF D98198419 INSPECTED BY IMWILSON WORK CENTER 940 SUPERVISOR SWJONES STATUS INSPT JCN CF QA REQ REQ MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN CORROSION SWP4826 Figure 16-47: Assisting Work Center (Different WUC) 16-175 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE SOX 1 D9865A3 SWP 96028 WHITE 1 D9865A2 SWP 96029 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96029 0900 3 3.5 1.5 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 06481 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI SA3 R 255 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 BK1 03 DATE ORD 96028 REQ NO 6028D212 DATE REC 96029 866554 WORK ACT

MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 958 01 3.5 3.5 7336200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96028 0800 06481 AAM025 IN WORK 96028 1400 96029 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 866542 96028 M3 3.5 TIME/CYCLES TIME/CYCLES M0625 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES W1000 X0111 STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96028 0800 DISCREPANCY ASQ-61 WILL NOT ZERO OUT PILOT/INITIATOR 96028 0800 IW 96028 1000 WP AT3 SMITH 96029 0900 M3 IW 96029 1230 CORRECTIVE ACTION REPLACED SA3 MODULE, REPAIRED WIRING. JC 96029 1400 HOT/SAC CHECKS GOOD. CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI BCM JHWHITE IBSMITH SWPATTERSON ECMERCER JOB CONTROL NUMBER ORG DAY SER SUF AC3028009

WORK CENTER 65A STATUS UP INSPT JCN PRI TURN-IN DDSN 3 6028G112 SYSTEM/REASON MCN ASQ-61 SWP4826 Figure 16-48: Component Repaired Using a Repairable Subassembly 16-176 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RED 1 D986908 SWP 96028 RED 1 D986908 SWP 96029 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96028 1030 3 0.5 1.0 96029 1400 3 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 06481 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI TB1A17 R 255 00001 PART NUMBER 746386 FSCM PART NUMBER FSCM PART NUMBER BK1 03 DATE ORD REQ NO 6028D229 96028 DATE REC 96029 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 255 01 3.0 3.0 7336240 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD

PERM CD AAEG 158689 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1000 96028 1100 06481 AAM025 IN WORK 96028 1600 96029 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 866542 96028 M3 1.5 TIME/CYCLES TIME/CYCLES M0625 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96028 1000 DISCREPANCY SA3 MODULE HAS NO OUTPUT PILOT/INITIATOR 96028 1030 M3 96028 1100 IW AT2 SMITH 96029 1300 WP M3 96029 1400 CORRECTIVE ACTION REPLACED CARD 673 LAMINATE 1 LOGIC IW 96029 1500 JC 96029 1600 TYPE 2 (TB1A17) CHECKS GOOD. CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM JHRED IBSMITH SWPATTERSON ECMERCER JOB CONTROL NUMBER ORG DAY SER SUF AC3028009A WORK CENTER 690 STATUS INSPT JCN PRI TURN-IN DDSN 3 6028D212 SYSTEM/REASON MCN SA3 MODULE SWP4826 Figure 16-49: Subassembly/Module Repair (Suffix) 16-177 COMNAVAIRFORINST 4790.2C 15 Jan 2017

N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MILLER 1 D9869B5 RSB 96029 MILLER 1 D9869B5 RSB 96030 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.3 96029 0800 3 1.0 0.4 96030 1000 3 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 06481 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R502 R 070 00001 PART NUMBER 74638-2 FSCM PART NUMBER FSCM PART NUMBER BK1 03 DATE ORD 96029 REQ NO 6029D601 DATE REC 96030 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 450 01 0.7 0.7 736324A D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1300 96028 0900 06481 36578 IN WORK 96029 1120 96030 COMP DATE AWAITING MAINTENANCE

HRS PART NUMBER REMOVED PART NUMBER 746386 96029 M3 2.0 TIME/CYCLES TIME/CYCLES M0625 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96028 1300 DISCREPANCY LOGIC BOARD OPEN PILOT/INITIATOR 96029 0800 M3 96029 0900 IW AT2 SMITH 96029 0915 WP M3 96030 1000 CORRECTIVE ACTION REPAIRED LOGIC BOARD. REPLACED RESISTOR IW 96030 1100 JC 96030 1120 CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM JHMILLER IBSMITH SWBRIGGS ECMERCER JOB CONTROL NUMBER ORG DAY SER SUF AC3028009AA WORK CENTER 69B STATUS INSPT JCN PRI TURN-IN DDSN 3 6028D229 SYSTEM/REASON MCN CARD 673 SWP4826 Figure 16-50: Sub-Subassembly/Module Repair (Double Suffix) 16-178 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DOE 1 D9865Q4 RIH 96129 DOE 1 D9865Q5 RIH 96138 ACCUMULATED AWM HOURS HOURS

DATE TIME REASON HOURS 1.0 1.5 LOCAL USE REFERENCE INDEX F/P FSCM AWP 77327 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 BK0 247AS10-100-001 02 DATE ORD 96126 REQ NO DATE REC 6126D111 96138 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 18 1 T 814 01 2.5 2.5 78HFG TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD M1124 GVAB 000060 O B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96129 0800 77327 UOI002 77327 IOU001 IN WORK 96129 1430 96138 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS10-100-001 96129 247AS10-100-001 M7676 M2121 TIME/CYCLES TIME/CYCLES M5000 M0101 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96129 0800 DISCREPANCY REMOVE BB10 FROM VAST # 1

PILOT/INITIATOR IW 96129 0800 WP 96138 0900 FOR VAST #2 AT3 SMITH IW 96138 1300 JC 96138 1430 CORRECTIVE ACTION R & R BB10 IN VAST #1 CF QA REQ REQ CORRECTED BY JHDOE JOB CONTROL NUMBER ORG DAY SER SUF D98129082 INSPECTED BY IBBOSSWELL WORK CENTER 65Q SUPERVISOR RIHAUGE STATUS UP INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 Figure 16-51: Cannibalization (End Item) 16-179 RFI BCM SYSTEM/REASON MCN BB10 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RICH 1 D986902 SWP 96028 JONES 1 D9869A3 96034 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX H I F/P AWP X X FSCM 06481 X FSCM 06481 FSCM A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 615 TB1A22 00001 PART NUMBER 17864-3 T 814 TB1A17 00001 PART NUMBER 746386 DATE ORD REQ NO BK1 03 96028 6028D114 BK1 03

96034 6034D101 DATE REC PART NUMBER WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7363240 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 152672 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96028 0800 0800 06481 13747 IN WORK 96028 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 866554 96028 TIME/CYCLES M0231 MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96028 0800 DISCREPANCY 5A3 OPEN IW 96028 0800 WP 96028 0900 VOLTAGE OUTPUT WT 96028 1100 WQ 96028 1200 CORRECTIVE ACTION WB 96034 0800 IW 96034 0900 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AT3 SMITH CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3028002A WORK CENTER 69A STATUS UP INSPT JCN PRI TURN-IN DDSN 3 6028D341 SYSTEM/REASON

MCN 5A3 CARD SWP4826 Figure 16-52: Cannibalization (From AWP Component) 16-180 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RICH 1 D986902 SWP 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX H I F/P AWP X X FSCM 61664 X FSCM 61664 FSCM A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 255 PART NUMBER T 814 PART NUMBER 00001 41618-1 00001 51678 DATE ORD REQ NO BK1 02 96198 6198D119 BK1 02 96198 6198D135 DATE REC PART NUMBER WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 78HPY27 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD GVAB 000060 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0730 96198

0800 77327 614 IN WORK 96198 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 247AS20-245 96198 TIME/CYCLES TIME/CYCLES M0231 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96198 0730 DISCREPANCY CIRCUIT 4418 HAS IMPROPER PILOT/INITIATOR 96198 0800 M3 96198 0800 IW VOLTAGE OUTPUT AS2 SMITH 96198 0855 WS WP 96198 0900 CORRECTIVE ACTION WT 96198 1200 WQ 96198 1300 CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI BCM JOB CONTROL NUMBER ORG DAY SER SUF D98129456AA WORK CENTER 690 STATUS UP INSPT JCN PRI TURN-IN DDSN 3 6198D116 SYSTEM/REASON MCN CIRCUIT CARD SWP4826 Figure 16-53: Cannibalization (Off-Equipment) 16-181 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RAINER 1 D9861B7 SWP 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS

3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 C 127 01 3.0 3.0 7236100 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 151611 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1100 96033 1100 82598 78 IN WORK 96033 1400 96033 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 15690 96033 M0431 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96033 1100 DISCREPANCY RADAR ALTIMETER READS 150 PILOT/INITIATOR IW 96033 1100 ABOVE PRESSURE ALTIMETER(MATCHED SET SEE JC 96033 1400 CPL SMITH JCN AF2033022) CORRECTIVE ACTION ADJUSTED RT601/APN-141.

CHECKS GOOD CORRECTED BY JHRAINER JOB CONTROL NUMBER ORG DAY SER SUF AF2033021 INSPECTED BY BBPOTTS WORK CENTER 61B SUPERVISOR IMLOGAN STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 6033G562 3 Figure 16-54: Matched Set (Repair) 16-182 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN RT601/APN SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE RAINER 1 D9861B7 SWP 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7236400 D98 31 2 A 806 01 3.0 3.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM

TECH INV CD PERM CD AFPH 151611 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1100 96033 1100 82598 1068 IN WORK 96033 1400 96033 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267 96033 TIME/CYCLES TIME/CYCLES M0431 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96033 1100 DISCREPANCY RADAR ALTIMETER READS 150 PILOT/INITIATOR IW 96033 1100 ABOVE PRESSURE ALTIMETER(MATCHED SET SEE JC 96033 1400 CPL SMITH JCN AF2033021) CORRECTIVE ACTION NO DEFECT. REMOVED AS PART OF A MATCHED SET. CHECKS GOOD WITH RT601/APN-141 CORRECTED BY JHRAINER JOB CONTROL NUMBER ORG DAY SER SUF AF2033022 INSPECTED BY BBPOTTS WORK CENTER 61B SUPERVISOR IMLOGAN STATUS UP INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6033G563 Figure 16-55: Matched Set (No Repair) 16-183 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN APN-141 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017

N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL/YOUNG 1 D9851E3 SWP 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX H F/P AWP X FSCM 86896 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 1 787 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC 00001 008347741SNGT1 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 32 2 C 787 01 3.0 1.5 13511 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151686 H B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96033 0800 26512 7482 IN WORK 96033 0930 96033 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 347H-1-2 96033 TIME/CYCLES TIME/CYCLES L0180

MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96033 0800 DISCREPANCY PORT TIRE WORN TO CORD. PILOT/INITIATOR 96033 0800 IW 96033 0930 JC AD3 SMITH CORRECTIVE ACTION BUILT UP NEW ASSY AND BCMD TIRE SER NO 0123456789 CORRECTED BY JHPOWELL JOB CONTROL NUMBER ORG DAY SER SUF AC3033025 INSPECTED BY BBBLACK WORK CENTER 51E SUPERVISOR BMCONLEY STATUS UP INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 4033D921 SYSTEM/REASON MCN A-6 TIRE SWP4826 Figure 16-56: Tire and Wheel Documentation (Tires Prepositioned in W/C) 16-184 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL/YOUNG 1 D9851E3 SWP 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX H F/P AWP X FSCM 86896 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL

QTY PROJ PRI R 787 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 BK1 008347741SNGT1 03 DATE ORD 96033 REQ NO DATE REC 6033D211 96033 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 32 2 C 787 01 3.0 1.5 13511 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151686 H B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96033 0800 26512 7482 IN WORK 96033 0930 96033 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 347H-1-2 96033 TIME/CYCLES TIME/CYCLES L0180 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96033 0800 DISCREPANCY PORT MAIN TIRE WORN TO CORD. PILOT/INITIATOR 96033 0800 IW 96033 0930 JC AD3 SMITH CORRECTIVE ACTION BUILT UP NEW ASSY. ORDERED AND REPLACED TIRE. CORRECTED BY JHPOWELL JOB CONTROL NUMBER ORG DAY SER SUF AC3033025

INSPECTED BY BBBLACK WORK CENTER 51E SUPERVISOR BMCONLEY STATUS UP INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 4033D921 SYSTEM/REASON MCN A-6 TIRE SWP4826 Figure 16-57: Tire and Wheel Documentation (Ordering Replacement Tire) 16-185 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JONES 1 D9865A2 SWB 96055 JONES 1 D9865A2 SWB 96075 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96050 0800 3 120.0 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 06481 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI P 169 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 123654-3-4 BK1 03 DATE ORD 96055 REQ NO DATE REC 6055D212 96075 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 D 169 01 3.0 3.0

7363200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151615 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96050 0800 06481 DBL-001 IN WORK 96055 0900 96075 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 123654-3 96050 M3 120.0 TIME/CYCLES TIME/CYCLES M0345 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES W1000 X0111 STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96050 0800 DISCREPANCY ASQ-61 WILL NOT ZERO OUT. PILOT/INITIATOR 96055 0800 IW 96055 1000 WP AT3 SMITH 96055 1115 WT WQ 96055 1120 CORRECTIVE ACTION "D" ACTION CLOSE OUT. OFF LOAD FROM SHIP WB 96075 0800 IW 96075 0800 CF QA JC 96075 0900 REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI BCM JJJONES IBSMITH IMLOGAN ECMERCER JOB CONTROL NUMBER ORG DAY SER SUF AC1050099 WORK CENTER 65A STATUS UP INSPT JCN PRI TURN-IN DDSN 1 4050D127 SYSTEM/REASON MCN ASQ-61 SWP4826

Figure 16-58: Transferring IMA Close Out (Post/Predeployment) 16-186 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7363200 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151615 D B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 06481 DBL-001 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 123654-3244-001 96050 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES

TIME/CYCLES TIME/CYCLES DISCREPANCY M0345 W1000 X0129 TIME/CYCLES TIME/CYCLES TIME/CYCLES ASQ-61 WILL NOT ZERO OUT. PILOT/INITIATOR AT3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC1050099 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6050D127 SYSTEM/REASON MCN ASQ-61 SWP4826 Figure 16-59: Receiving IMA (Reinitiation Documentation) 16-187 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 235DA00

2 140 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 158689 Y B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 14386 6313 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 123456-1 96107 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES C9999 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY FUEL PUMP RECEIVED (AND INSTALLED) WITHOUT SRC CARD PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3107153 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6107G134 Figure 16-60: Component Missing SRC Card 16-188 BCM SYSTEM/REASON MCN FUEL PUMP SRC SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS

MAN NAME/SHIFT TOOLBOX/INT DATE JONES 1 D9865A3 SWP 96028 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 7363200 D98 11 2 Z C01 01 1.5 1.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 159689 W B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96028 0830 0830 IN WORK 96028 96028 1000 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96028 0830 DISCREPANCY ASQ-61 NEEDS CORROSION PILOT/INITIATOR IW 96028 0830 JC 96028 1000 AT2 DEAN TREATMENT CORRECTIVE

ACTION TREATED CORROSION CONNECTOR TERMINAL CF QA REQ REQ CORRECTED BY JHJONES JOB CONTROL NUMBER ORG DAY SER SUF AC3028009 INSPECTED BY IMWILSON WORK CENTER 65A SUPERVISOR JBSMITH STATUS UP INSPT JCN MAINT CONTROL AT1 MERCER PRI TURN-IN DDSN 3 Figure 16-61: Corrosion Supporting MAF 16-189 RFI BCM SYSTEM/REASON MCN ASQ-61 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER WORK ACT MAL UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT DATE ORD REQ NO DATE REC TECHNICAL DIRECTIVE ID INT CODE BASIC NO RV AM PART KIT A 1 01 0124 00 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA

662151 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 77445 662151 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8C 96055 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY E1234 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AZ3 SMITH COMPLY WITH PPB-124A AM1 CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88055413 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN PPB-124A AM1 SWP4826 Figure 16-62: Turn-In from Supply for TD Compliance 16-190 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-63: VIDS/MAF Work Request (Production Control Entries) 16-191 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-64: VIDS/MAF Work Request (Local Manufacture/Fabrication) 16-192 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-65: VIDS/MAF

Work Request (Supply Asset Build-Up Induction) 16-193 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11310 D98 30 2 A 571 01 3.0 1.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 155684 O G REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96190 0800 0800 12345 530 IN WORK 96190 96190 0930 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART

NUMBER 4124111-3 96190 TIME/CYCLES TIME/CYCLES A2630 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96190 0800 DISCREPANCY NDI LAUNCH BAR UPLOCK PILOT/INITIATOR IW 96190 0800 JC 96190 0930 FITTING. POC AMC WILSON, EXT 9-7457 CPL SMITH CORRECTIVE ACTION PERFORMED MAGNETIC PARTICLE INSP ON LAUNCH BAR UPLOCK FITTING. NO DEFECTS NOTED CORRECTED BY JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190A06 INSPECTED BY IBCAROL WORK CENTER 530 SUPERVISOR IMMUNGER STATUS UP INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 CF QA REQ REQ RFI SYSTEM/REASON MCN NDI FITTING SWP4826 Figure 16-66: Scheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) 16-194 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE

TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 A 570 01 3.0 1.5 11310 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 155684 O G REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96190 0800 IN WORK 96190 0930 96190 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96190 0800 DISCREPANCY X-RAY INTAKE RAMPS IAW MRC F-28. PILOT/INITIATOR 96190 0800 IW 96190 0930 JC POC AMC WILSON, EXT 9-7457 CPL SMITH CORRECTIVE ACTION X-RAY COMPLETED. NO DEFECT CF QA REQ REQ CORRECTED BY

JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190A06 INSPECTED BY IBCAROL WORK CENTER 530 SUPERVISOR IMMUNGER STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN X-RAY RAMPS SWP4826 Figure 16-67: Scheduled Maintenance Work Request (NDI On-Site) (Passed Inspection) 16-195 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 F 570 01 3.0 1.5 11310 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE

FSCM TECH INV CD PERM CD AFPH 155684 O G REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96190 0800 IN WORK 96190 0930 96190 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96190 0800 DISCREPANCY X-RAY INTAKE RAMPS IAW MRC F-28. PILOT/INITIATOR 96190 0800 IW 96190 0930 JC POC AMC WILSON, EXT 9-7457 CPL SMITH CORRECTIVE ACTION X-RAY COMPLETED. FAILED X-RAY INSP CF QA REQ REQ CORRECTED BY JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190A06 INSPECTED BY IBCAROL WORK CENTER 530 SUPERVISOR IMMUNGER STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN X-RAY RAMPS SWP4826 Figure 16-68: Scheduled Maintenance Work Request (NDI On-Site) (Failed Inspection) 16-196 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV

2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 F 571 01 3.0 1.5 11310 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 155684 O G REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96190 0800 12345 530 IN WORK 96190 0930 96190 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4124111-3 96190 A2630 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3

96190 0800 DISCREPANCY NDI LAUNCH BAR UPLOCK FITTING PILOT/INITIATOR IW 96190 0800 JC 96190 0930 POC AMC WILSON, EXT 9-7457 CPL SMITH CORRECTIVE ACTION PERFORMED MAGNETIC PARTICLE INSP ON LAUNCH BAR UPLOCK FITTING. FAILED INSPECTION CORRECTED BY JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190A06 INSPECTED BY IBCAROL WORK CENTER 530 SUPERVISOR IMMUNGER STATUS INSPT JCN CF QA REQ REQ MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN NDI FITTING SWP4826 Figure 16-69: Scheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) 16-197 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART

NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 A 571 01 3.0 1.5 11310 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 155684 O S REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96190 0800 12345 530 IN WORK 96190 0930 96190 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4124111-3 96190 A2630 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96190 0800 DISCREPANCY NDI NLG DRAG BRACE. HARD LANDING PILOT/INITIATOR IW 96190 0800 JC 96190 0930 POC AMC WILSON, EXT 9-7457 CPL SMITH CORRECTIVE ACTION PERFORMED MAGNETIC PARTICLE INSP ON NLG DRAG BRACE. PASSED INSPECTION CORRECTED BY JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190250 INSPECTED BY IBCAROL WORK CENTER 530

SUPERVISOR IMMUNGER STATUS INSPT JCN CF QA REQ REQ MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN NDI DRAG BR SWP4826 Figure 16-70: Unscheduled Maintenance Work Request (NDI In-Shop) (Passed Inspection) 16-198 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE YATES/KEEPING 1 D985302 TRC 96190 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 F 571 01 3.0 1.5 11310 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFPH 155684 O S REPAIR CYCLE DATE TIME EOC

REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96190 0800 12345 530 IN WORK 96190 0930 96190 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4124111-3 96190 TIME/CYCLES TIME/CYCLES A2630 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96190 0800 DISCREPANCY NDI NLG DRAG BRACE. HARD PILOT/INITIATOR 96190 0800 IW 96190 0930 JC LANDING POC AMC WILSON, EXT 9-7457 CPL KLINGER CORRECTIVE ACTION PERFORMED MAGNETIC PARTICLE INSP ON NLG DRAG BRACE. FAILED INSPECTION CORRECTED BY JHYATES JOB CONTROL NUMBER ORG DAY SER SUF AA1190250 INSPECTED BY DLYARBROUGH WORK CENTER 530 STATUS SUPERVISOR DBADAMS INSPT JCN CF QA REQ REQ MAINT CONTROL LDCUMMINGS PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN NDI DRAG BR SWP4826 Figure 16-71: Unscheduled Maintenance Work Request (NDI In-Shop) (Failed Inspection) 16-199 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV

4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 751BE00 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AMAF 164150 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 76301 10096 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES U0012 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY LAU-116/A MISSILE LAUNCHER DUE FOR 224 DAY INSP. PILOT/INITIATOR CPL

BUCHANAN CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AW1027112 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN LAU-116 INSP SWP4826 Figure 16-72: O-Level Armament Equipment Turn-In for Scheduled Maintenance 16-200 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C71C9 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 A 804 01 3.5 3.5 751BE00 A9C TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI

METER SE FSCM TECH INV CD PERM CD AMAF 164150 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96027 0800 76301 10096 IN WORK 96027 1130 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 TIME/CYCLES TIME/CYCLES U0012 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0800 DISCREPANCY LAU-116/A MISSILE LAUNCHER PILOT/INITIATOR 96027 0800 M3 96027 0800 IW DUE FOR 224 DAY INSP. CPL BUCHANAN 96027 1130 JC CORRECTIVE ACTION COMPLETED 224 DAY INSP PER MIMS NO DISCREPANCIES NOTED. CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF AW1027112 INSPECTED BY IQSMITH WORK CENTER 71C SUPERVISOR ICBUTLER STATUS UP INSPT JCN MAINT CONTROL JHBALL PRI TURN-IN DDSN 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN LAU-116 SWP4826 Figure 16-73: O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (No Material Required)

(Completed) 16-201 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C71C9 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.5 LOCAL USE REFERENCE INDEX H F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI X FSCM R 070 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 74R73002-4 BK1 DATE ORD 06 96027 REQ NO DATE REC 6027DE02 96027 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 751BE00 A9C 32 2 C 804 01 3.5 3.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AMAF 164150 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96027 0745 0745 76301 10096 IN WORK 96027 96027 1130 COMP DATE AWAITING MAINTENANCE HRS

PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 U0012 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0745 DISCREPANCY LAU-116/A MISSILE LAUNCHER PILOT/INITIATOR M3 96027 0800 IW 96027 0800 DUE FOR 224 DAY INSP. CPL BUCHANAN JC 96027 1130 CORRECTIVE ACTION COMPLETED 224 DAY INSP PER MIMS R & R RELEASE MECHANISM. CHECKS GOOD CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF AW1027112 INSPECTED BY IQSMITH WORK CENTER 71C SUPERVISOR ICBUTLER STATUS UP INSPT JCN MAINT CONTROL JHBALL PRI TURN-IN DDSN 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN LAU-116 INSP SWP4826 Figure 16-74: O-Level Armament Equipment Component Turn-In for Scheduled Maintenance (Maintenance and Material Required) (Completed) 16-202 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN

DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 30 2 751BE00 A9C TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 010096 O B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 76301 10096 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES U0012 DISCREPANCY PERFORM ACCEPTANCE/ FUNCTIONAL CHECK ON LAU-116A/A MISSILE LAUNCHER RECD FROM NAS CECIL FIELD PILOT/INITIATOR CPL BUCHANAN CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY

INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF C99027112 WORK CENTER 71C STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN LAU-116 ACCP SWP4826 Figure 16-75: Turn-In Acceptance/Functional Check on Armament Equipment 16-203 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JONES 1 1C9971C1 KRJ 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 30 2 A 804 01 1.0 1.0 751BE00 A9C TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 010096 O B REPAIR

CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96027 76301 10096 0800 IN WORK 96027 0900 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 TIME/CYCLES TIME/CYCLES U0012 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96027 0800 DISCREPANCY PERFORM ACCEPTANCE/ PILOT/INITIATOR 96027 0800 IW FUNCTIONAL CHECK ON LAU-116A/A MISSILE 96027 0900 JC CPL BUCHANAN LAUNCHER RECD FROM NAS CECIL FIELD CORRECTIVE ACTION PERFORMED FUNCTIONAL CHECK. NO DEFECTS NOTED. CORRECTED BY IMJONES JOB CONTROL NUMBER ORG DAY SER SUF C99027112 INSPECTED BY KRJOE WORK CENTER 71C CF QA REQ REQ SUPERVISOR KRJOE STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN LAU-116 FUNC SWP4826 Figure 16-76: Turn-In Acceptance/Functional Check on Armament Equipment (Completed) 16-204 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN

SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT ROSS 1 C9971C1 MAN DATE 96198 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 2 0 000 01 2.0 2.0 049 C99 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 001096 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96198 0900 IN WORK 96198 1100 96198 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96198 0800

DISCREPANCY PRESERVE LAU-116A/A MISSILE PILOT/INITIATOR IW 96198 0900 JC 96198 1100 LAUNCHER IBSTEELE CORRECTIVE ACTION PRESERVED MISSILE LAUNCHER CF QA REQ REQ CORRECTED BY THROSS JOB CONTROL NUMBER ORG DAY SER SUF C99198002 INSPECTED BY KRJOE WORK CENTER 71C SUPERVISOR KRJOE STATUS INSPT JCN MAINT CONTROL BMERCER PRI TURN-IN DDSN 1 RFI BCM SYSTEM/REASON MCN PRESERVE SWP4826 Figure 16-77: Armament Equipment Pool Preservation/Depreservation Control Document (Completed) 16-205 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JONES 1 A9C71C9 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID

UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 751BE00 A9C 31 2 A 804 01 3.5 3.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 010096 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96027 0745 76301 10096 IN WORK 96027 1130 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 74A730301-1016 96027 TIME/CYCLES U0012 MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES A1 96027 0745 DISCREPANCY LAU-116/A MISSILE M3 96027 0800 LAUNCHER DUE FOR 224 DAY INSP. IW 96027 0800 JC 96027 1130 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR CPL BUCHANAN CORRECTIVE ACTION COMPLETED 224 DAY INSP PER MIMS NO DISCREPANCIES NOTED. CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF A9C027710 INSPECTED BY IQSMITH WORK CENTER 71C SUPERVISOR ICBUTLER STATUS UP INSPT JCN MAINT CONTROL JHBALL PRI TURN-IN DDSN 3 CF QA

REQ REQ X RFI BCM SYSTEM/REASON MCN LAU-116 SWP4826 Figure 16-78: I-Level Armament Equipment Pool Component Due for Scheduled Maintenance (Completed) 16-206 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C81A11 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.5 LOCAL USE REFERENCE INDEX F/P AWP H A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM R 804 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 607AS101-31 BK1 03 DATE ORD 96027 REQ NO DATE REC 6027ED50 96027 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 91A2C00 A9C 32 2 C 804 01 2.5 2.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AFWC 163200 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW

ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96027 0745 0745 30003 00186 IN WORK 96027 96027 1030 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 607AS100-4 96027 TIME/CYCLES TIME/CYCLES A1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0745 DISCREPANCY NES-14/A PARACHUTE DUE FOR 448 PILOT/INITIATOR 96027 0800 M3 96027 0800 IW DAY INSP. POC PR1 WILSON, EXT 9-7457 CPL BUCHANAN 96027 1030 JC CORRECTIVE ACTION COMPLETED 448 DAY INSP PER MIMS R & R DROGUE CHUTE. CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF AW1027005 INSPECTED BY IQSMITH WORK CENTER 81A SUPERVISOR ICBUTLER STATUS UP INSPT JCN MAINT CONTROL JHBALL PRI TURN-IN DDSN 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN NES-14/A SWP4826 Figure 16-79: O-Level ALSS Equipment Due for Scheduled Maintenance (Maintenance and Material Required) (Completed) 16-207 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV

4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C81B11 ICB 96027 JPJONES 1 A9C81B11 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 96027 0900 8 4.0 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 96B1600 A9C 31 2 A 804 01 2.5 2.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YPAA JP7794 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96027 0800 30003 10096 IN WORK 96027 1430 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 68A73H1-103 96027 M8 4.0 TIME/CYCLES TIME/CYCLES A0000 MAINTENANCE/SUPPLY REC

TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0745 DISCREPANCY LPU-21C/P LIFE PRESERVER DUE PILOT/INITIATOR M3 96027 0800 IW 96027 0800 FOR 90 DAY INSP. POC PR1 WILSON, EXT 9-7457 PR3 BUCHANAN M8 96027 0900 IW 96027 1300 CORRECTIVE ACTION COMPLETED 90 DAY INSP PER MIMS. JC 96027 1430 NO DISCREPANCIES NOTED. CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM JPJONES IQSMITH ICBUTLER JHBALL JOB CONTROL NUMBER ORG DAY SER SUF AW1027005 WORK CENTER 81B STATUS UP INSPT JCN PRI TURN-IN DDSN 3 SYSTEM/REASON MCN LPU-21C/P SWP4826 Figure 16-80: O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Completed) 16-208 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C81B11 ICB 96027 JPJONES 1 A9C81B11 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS

1.0 96027 0900 8 4.0 1.5 LOCAL USE REFERENCE INDEX H F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI X FSCM R 381 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 68A73B2-3 BK1 03 DATE ORD 96027 REQ NO DATE REC 6027DF80 96027 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 804 01 2.5 2.5 96B1600 A9C TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YPAA JP7794 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96027 0745 30003 10096 IN WORK 96027 1430 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 68A73H1-103 96027 M8 4.0 TIME/CYCLES TIME/CYCLES A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0745 DISCREPANCY LPU-21C/P LIFE PRESERVER DUE PILOT/INITIATOR 96027 0800 M3 96027 0800 IW FOR 90 DAY

INSP. POC PR1 WILSON, EXT 9-7457 PR3 BUCHANAN 96027 0900 M8 IW 96027 1300 CORRECTIVE ACTION COMPLETED 90 DAY INSP PER MIMS. JC 96027 1430 R & R AND PLACED NEW BLADDER IN SERVICE. CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF AW1027005 INSPECTED BY IQSMITH WORK CENTER 81B SUPERVISOR ICBUTLER MAINT CONTROL JHBALL INSPT STATUS JCN PRI TURN-IN DDSN UP 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN LPU-21C/P SWP4826 Figure 16-81: O-Level ALSS Personal Equipment Due For Scheduled Maintenance (Maintenance and Material Required) (Completed) 16-209 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X MLHAGAN ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JPJONES 1 A9C81C9 ICB 96027 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM

PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 47A1300 A9C 31 2 A 804 01 3.5 3.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 010096 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0745 96027 0745 19062 10096 IN WORK 96027 1130 96027 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 10C-0016-16 96027 TIME/CYCLES TIME/CYCLES A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96027 0745 DISCREPANCY LOX CONVERTER DUE FOR 224 PILOT/INITIATOR M3 96027 0800 IW 96027 0800 DAY INSP PR3 BUCHANAN JC 96027 1130 CORRECTIVE ACTION COMPLETED 224 DAY INSP PER MIMS. NO DISCREPANCIES NOTED. CORRECTED BY JPJONES JOB CONTROL NUMBER ORG DAY SER SUF A9C027810 INSPECTED BY IQSMITH WORK CENTER 81C SUPERVISOR ICBUTLER STATUS UP

INSPT JCN MAINT CONTROL JHBALL PRI TURN-IN DDSN 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN LOX CONVTR SWP4826 Figure 16-82: I-Level ALSS Pool Component Due for Scheduled Maintenance (Completed) 16-210 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-83: VIDS/MAF Discrepancy (Supply Asset Induction Document) (Material Condition Tag Missing) 16-211 COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-84: Completed Discrepancy VIDS/MAF (Supply Asset Induction Document) (Material Condition Tag Missing) 16-212 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD

ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 50 0054 A1 13125 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151688 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 64124 4113-21 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 912473-1 96033 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY TIME/CYCLES TIME/CYCLES TIME/CYCLES 1234 COMPLY WITH PARA II OF AFC 54 PILOT/INITIATOR AZ3 GRANT CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3033061 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN AFC 54 SWP4826 Figure 16-85: TD Compliance Turn-In Document (O-Level) 16-213 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED

SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BELL/HALL 1 D9852A2 GSH 96033 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 50 0054 A1 D98 47 2 A 00 1.0 0.5 13125 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD AAEG 151688 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96033 0800 64124 4113-21 64124 4113-21 IN WORK 96033 0830 96033 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 912473-1 96033 912473-1 TIME/CYCLES TIME/CYCLES A1234 A1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES

TIME/CYCLES M3 96033 0800 DISCREPANCY COMPLY WITH PARA II OF AFC 54 PILOT/INITIATOR 96033 0800 IW 96033 0830 JC AZ3 GRANT CORRECTIVE ACTION COMPLIED WITH PARA II OF AFC 54 CF QA REQ REQ CORRECTED BY ABHALL JOB CONTROL NUMBER ORG DAY SER SUF AC3033061 INSPECTED BY DAHANDS WORK CENTER 52A SUPERVISOR DAHANDS STATUS UP INSPT JCN MAINT CONTROL CLBROWN PRI TURN-IN DDSN 3 Figure 16-86: TD Compliance (IMA Assist) 16-214 RFI BCM SYSTEM/REASON MCN AFC 54 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV

AM PART KIT 54 0087 00 7236400 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 82598 1063 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267 96033 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY ALTIMETER A0000 TIME/CYCLES TIME/CYCLES TIME/CYCLES INCORPORATE AVC 87 IN RADAR PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AF2033035 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN Figure 16-87: Turn-In for TD Compliance 16-215 BCM SYSTEM/REASON MCN AVC 87 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT

TOOLBOX/INT DATE WILCOX/COX 1 D9861B2 RIC 96083 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 54 0087 00 47 2 C 01 1.0 0.5 7236400 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96083 0800 82598 1063 82598 1063 IN WORK 96083 0830 96083 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267 96033 1267-1 TIME/CYCLES TIME/CYCLES A0000 A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96083 0800 DISCREPANCY INCORPORATE AVC 87 IN RADAR PILOT/INITIATOR 96083

0800 IW 96083 0830 JC ALTIMETER AZ3 SMITH CORRECTIVE ACTION INCORPORATED AVC 87 IN RADAR ALTIMETER CORRECTED BY ABWILCOX JOB CONTROL NUMBER ORG DAY SER SUF AF2083035 INSPECTED BY GSMURRY WORK CENTER 61B SUPERVISOR RICLAUSEN STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 Figure 16-88: IMA TD Compliance 16-216 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN AVC 87 SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DELONG/WRIGHT 1 D9861B2 RIL 96270 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.8 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 54 0087 00 47

2 Q 01 0.8 0.4 7236400 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YCAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96270 0800 82598 1063 82598 1063 IN WORK 96270 0820 96270 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1267-1 96270 1267 TIME/CYCLES TIME/CYCLES A0000 A0000 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96270 0800 DISCREPANCY REMOVE AVC 87 FROM RADAR PILOT/INITIATOR 96270 0800 IW 96270 0820 JC ALTIMETER PER NASC MSG 270740Z SEP 93 AZ3 SMITH CORRECTIVE ACTION REMOVED AVC 87 FROM RADAR ALTIMETER CF QA REQ REQ CORRECTED BY ABDELONG JOB CONTROL NUMBER ORG DAY SER SUF AF2270072 INSPECTED BY GSCLARK WORK CENTER 61B SUPERVISOR RILARSON STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 Figure 16-89: TD Compliance Removal 16-217 RFI BCM SYSTEM/REASON MCN AVC 87 SWP4826

COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 23500 301 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 H B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER JHHA1 663223 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 96104 0.1 TIME/CYCLES TIME/CYCLES E1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES DISCREPANCY

COMPRESSOR CASE CRACKED FROM PILOT/INITIATOR FOD. FOR INSP USE JCN AC3104A00 AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 WORK CENTER STATUS INSPT JCN A00 PRI TURN-IN DDSN 6104G221 SYSTEM/REASON MCN 663223 MOM SWP4826 Figure 16-90: O-Level Turn-In Control Document for Engine Repair 16-218 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 96030 0900 3 0.1 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 11 2 0 000 01 0.0 0.0 049

TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 649300 O D REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0900 96030 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 0.1 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96030 0900 DISCREPANCY UNCAN AND DEPRESERVE ENGINE PILOT/INITIATOR 649300 PER NA 15-01-500 AZ1 BOLYARD CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88030002 WORK CENTER 41A STATUS INSPT JCN 002 PRI TURN-IN DDSN 2 SYSTEM/REASON MCN UNCAN/DEPRE SWP4826 Figure 16-91: Supply Asset Engine Depreservation 16-219 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 Figure 16-92: Supply Asset Engine (Assist VIDS/MAF) Test Cell Run 16-220 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826

VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE LESCH 1 D9841A6 TRH 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 2 C 160 01 0.5 0.5 235DA00 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 0800 IN WORK 96104 0830 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104

0800 DISCREPANCY FUEL PUMP HAS BROKEN LEAD PILOT/INITIATOR 96104 0800 IW 96104 0830 JC AD1 SMITH CORRECTIVE ACTION REPAIRED BROKEN LEAD CF QA REQ REQ CORRECTED BY JHLESCH JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 INSPECTED BY IMLALLY WORK CENTER 41A SUPERVISOR JBREEVES STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN FUEL PUMP SWP4826 Figure 16-93: Fix-In-Place (Material Not Required) 16-221 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MILLER 1 D9841A12 RIB 96104 MILLER 1 D9841A12 RIB 96106 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 46448 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R 070 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 334167-2 ZQ9 03 DATE ORD 96104 REQ NO DATE REC

6104D256 96106 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 235DK D98 12 2 C 070 01 2.0 2.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 0800 IN WORK 96104 96106 0900 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY BROKEN OIL TUBE PILOT/INITIATOR IW 96104 0800 WP 96104 0900 AD1 DEAN IW 96106 0800 JC 96106 0900 CORRECTIVE ACTION REPLACED BROKEN OIL TUBE CF QA REQ REQ CORRECTED BY SWMILLER JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 INSPECTED BY IMDREW WORK CENTER 41A SUPERVISOR RIBOGIE STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 Figure 16-94: Fix-In-Place (Material

Required) 16-222 RFI BCM SYSTEM/REASON MCN OIL TUBE SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE ERTMAN 1 D9841A10 RLK 96104 DUNCAN 1 D9841A10 RLK 96107 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 2.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 6049T41P01 ZQ9 03 DATE ORD 96105 REQ NO DATE REC 6105DZ40 96107 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 235F6 D98 18 2 R 710 01 3.5 3.5 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 0800 99207

MDU1502 99207 MDU1429 IN WORK 96104 1000 96107 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6049T41P01 96104 6049T41P01 TIME/CYCLES TIME/CYCLES A1234 A1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY R & R # 4 BEARING DUE TO PILOT/INITIATOR IW 96104 0800 WS 96104 0930 EVIDENCE OF OVERHEATING AD1 SMITH WP 96105 0800 IW 96107 0800 CORRECTIVE ACTION R & R # 4 BEARING JC 96107 1000 CF QA REQ REQ CORRECTED BY JHDUNCAN JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 INSPECTED BY IBEMBACH WORK CENTER 41A SUPERVISOR IMKRIS STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN R/R #4 BRNG SWP4826 Figure 16-95: Removal/Replacement of a Tracked Consumable Component 16-223 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS MAN

NAME/SHIFT TOOLBOX/INT DATE DUNCAN 1 D9841A10 RLK 96104 1 D9841A10 RLK 96107 ERTMAN ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI 00001 FSCM 23810 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER ZQ9 03 DATE ORD 96105 REQ NO 6105DZ36 DATE REC 96107 667237 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 23 2 R 381 01 3.5 3.5 235DD TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 0800 23810 FP26 23810 FP16 IN WORK 96104 1000 96107 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 667237 96104 667237 TIME/CYCLES TIME/CYCLES C1313 C0001 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES

TIME/CYCLES M3 96104 0800 DISCREPANCY FUEL PRESSURIZING DUMP VALVE PILOT/INITIATOR 96104 0800 IW 96104 0930 WS ASSY LEAKING AD1 SMITH 96105 0800 WP IW 96107 0800 CORRECTIVE ACTION R & R FUEL PRESSURIZING DUMP VALVE ASSY JC 96107 1000 CF QA REQ REQ CORRECTED BY JHDUNCAN JOB CONTROL NUMBER ORG DAY SER SUF AC31040011A INSPECTED BY IBEMBACH WORK CENTER 41A SUPERVISOR IMKRIS STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN R/R DUMP VAL SWP4826 Figure 16-96: Removal/Replacement of a Repairable Component with No Repairable SubSubassemblies 16-224 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE LAND 1 D9841A21 RJP 96104 DAYS/3 1 D9841A21 RJP 96107 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 12.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 13416 A/T FAILED / REQUIRED MATERIAL

MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 6671181 ZQ9 03 DATE ORD 96104 REQ NO DATE REC 6104DZ38 96107 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 2351C10 D98 23 2 R 301 01 16.2 8.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 0800 13416 T00817 13416 T11061 IN WORK 96104 96107 1200 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6671181 96104 6671181 TIME/CYCLES TIME/CYCLES C0931 C0001 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY FRONT COMPRESSOR STATORS PILOT/INITIATOR IW 96104 0800 WP 96104 1200 FODDED AD2 SMITH IW 96107 0800 JC 96107 1200 CORRECTIVE ACTION R & R FRONT COMPRESSOR CF QA REQ REQ

CORRECTED BY JHSWANSON JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 INSPECTED BY IBKRAMER WORK CENTER 41A SUPERVISOR RL PERRY STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN R/R FRT COMP SWP4826 Figure 16-97: Removal/Replacement of a Repairable Component with Repairable SubSubassemblies 16-225 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DORAN 1 D9862A3 IBH 96104 THOMAS 1 D9862A5 IBH 96109 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96104 1000 8 118.0 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 2351C00 D98 11 2 S 800

02 4.0 4.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 O 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 0800 IN WORK 96104 96109 1000 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M8 118.0 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY R & R WIRING HARNESS TO PILOT/INITIATOR IW 96104 0800 M8 96104 1000 FACILITATE REPAIR AZ1 BOLYARD IW 96109 0800 JC 96109 1000 CORRECTIVE ACTION Rd & Rd WIRING HARNESS TO FACILITATE REPAIR CORRECTED BY JHDORAN JOB CONTROL NUMBER ORG DAY SER SUF AC3104001 CF QA REQ REQ INSPECTED BY IMBROWN WORK CENTER 62A SUPERVISOR RIHARRIS STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 Figure 16-98: Facilitate Other Maintenance 16-226 RFI BCM SYSTEM/REASON MCN HARNES(FOM) SWP4826 COMNAVAIRFORINST

4790.2C 15 Jan 2017 Figure 16-99: Engine Repair Control Document (Completed VIDS/MAF) 16-227 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 30 2 23500 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHP 649300 O T REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0900 96030 77445 649300 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8B 96030 MAINTENANCE/SUPPLY

REC STATUS DATE TIME EOC M3 96030 0900 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY E4530 TIME/CYCLES TIME/CYCLES TIME/CYCLES BUILD-UP ENGINE TO A QECA PILOT/INITIATOR AD1 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88030001 WORK CENTER 41A STATUS INSPT JCN PRI TURN-IN DDSN 2 Figure 16-100: Supply Asset Engine Build-Up 16-228 BCM SYSTEM/REASON MCN 649300 QEC SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE

BASIC NO RV AM PART KIT 301 2351C10 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 w 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96104 13416 T11061 IN WORK 96104 1200 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6671181 96104 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96104 1200 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY C0931 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AD1 SMITH FRONT COMPRESSOR STATORS FODDED CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3104001A WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6104DZ38 SYSTEM/REASON MCN COMPRESSOR SWP4826 Figure 16-101: Engine Component Turn-In for Repair 16-229 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED

SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DAY/3 1 D9841A3 RIS 96106 NIGHT/2 1 D9841A3 RIS 96106 DAY/3 1 D9841A3 RIS 96107 NIGHT/1 1 D9841A3 RIS 96107 DAY/2 1 D9841A3 RIS 96108 LOCAL USE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 24.0 96104 1300 3 43.0 16.0 24.0 16.0 10.0 REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 C 301 01 90.0 450 2351C10 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96104 0800 13416 T11061 IN WORK 96106 0500 96108 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6671181 96104 M3

43.0 TIME/CYCLES TIME/CYCLES C0931 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96104 1200 DISCREPANCY FRONT COMPRESSOR STATORS PILOT/INITIATOR 96104 1300 M3 96106 0800 IW FODDED AZ1 SMITH 96108 0500 JC CORRECTIVE ACTION BLENDED STATORS CORRECTED BY JHOATES JOB CONTROL NUMBER ORG DAY SER SUF AC3104001A INSPECTED BY IBSPEAKER WORK CENTER 41A SUPERVISOR SWSWANE STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6104DZ38 SYSTEM/REASON MCN COMPRESSOR SWP4826 Figure 16-102: Engine Component Repair (Completed) 16-230 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM

PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 0300600 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHDB 664243 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER JHDB2 664243 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96094 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC E1248 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY TIME/CYCLES TIME/CYCLES TIME/CYCLES # 2 ENGINE DUE 600 HOUR INSP PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3094B00 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6094G428 SYSTEM/REASON MCN 664243 MOM SWP4826 Figure 16-103: Turn-In Document Solely for Major Engine Inspection 16-231 BCM COMNAVAIRFORINST

4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 0 000 01 0.0 0.0 0300600 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHDB 664243 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96094 0800 JHDB2 664243 IN WORK 96094 1700 96102 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96094 TIME/CYCLES TIME/CYCLES E1248 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME

EOC TIME/CYCLES TIME/CYCLES M3 96094 0800 DISCREPANCY # 2 ENGINE DUE 600 HOUR INSP PILOT/INITIATOR 96094 0800 IW 96094 1300 M3 AD1 SMITH 96095 0800 IW WP 96095 1400 CORRECTIVE ACTION COMPLETED 600 HR MAJOR INSP IW 96102 0900 JC 96102 1700 CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM JHRAINES IBPENROD RACLARK BNPOWELL JOB CONTROL NUMBER ORG DAY SER SUF AC3094B00 WORK CENTER 41A STATUS INSPT JCN B00 PRI TURN-IN DDSN 3 6094G428 SYSTEM/REASON MCN 664243 MOM SWP4826 Figure 16-104: Control Document Solely for Major Engine Inspection (Completed) 16-232 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER

DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 2 0 000 01 0.0 0.0 0301200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 0800 IN WORK 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY PERFORM 1200 HR MAJOR INSP PILOT/INITIATOR 96104 0800 IW PER MRC"s AZ2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3104A00 WORK CENTER 41A STATUS INSPT JCN A00 PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN 663223 INSP SWP4826 Figure 16-105: Control Document for Major Engine

Inspection (Engine Undergoing Repair) 16-233 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE JHDOE 1 D986203 JBP 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 8.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 0301200 D98 11 2 0 000 00 8.0 8.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 0800 IN WORK 96104 1600 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES

TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY COMPLY WITH MRCs 6, 9, 13 AND 15 PILOT/INITIATOR IW 96104 0800 JC 96104 1600 AZ1 STEELE CORRECTIVE ACTION COMPLETED CARDS 6, 9, 13 AND 15 CF QA REQ REQ CORRECTED BY JHDOE JOB CONTROL NUMBER ORG DAY SER SUF AC3104A00 INSPECTED BY KRJONES WORK CENTER 620 SUPERVISOR JBPOWELL STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN 663223 LOOK SWP4826 Figure 16-106: Major Engine Inspection (Look Phase Supporting Work Center) 16-234 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MANN 1 D9841A7 SIP 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART

NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 11 2 B 105 01 0.5 0.5 235DK TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 M 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0830 96104 0830 IN WORK 96104 0900 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0830 DISCREPANCY EXTERNAL OIL TUBE HOLD DOWN PILOT/INITIATOR 96104 0830 IW 96104 0900 JC BOLT ROUNDED OFF AD1 LLOYD CORRECTIVE ACTION REPLACED BOLT CF QA REQ REQ CORRECTED BY JHMANN JOB CONTROL NUMBER ORG DAY SER SUF AC3104A01 INSPECTED BY IMCOX WORK CENTER 41A SUPERVISOR SIPOTTER STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN

DDSN 3 BCM SYSTEM/REASON MCN OIL TUBE BLT SWP4826 Figure 16-107: Major Engine Inspection (Fix-In-Place) 16-235 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE HAYES 1 D9841A3 SWK 96105 HAYES 1 D9841A3 SWK 96106 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 123456-1 ZQ9 03 DATE ORD 96105 REQ NO 6105DZ33 DATE REC 96106 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 23 2 R 381 01 2.0 2.0 235DA00 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0700 RECD FSCM

SERIAL NUMBER FSCM SERIAL NUMBER 96105 0700 14386 6989 14386 9313 IN WORK 96105 0900 96106 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 123456-1 96105 123456-1 TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96105 0700 DISCREPANCY FUEL PUMP LEAKING IW 96105 0700 WP 96105 0800 IW 96106 0800 JC 96106 0900 CORRECTIVE ACTION R & R FUEL PUMP TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AD2 SMITH CF QA REQ REQ CORRECTED BY JHHAYES JOB CONTROL NUMBER ORG DAY SER SUF AC3104A02 INSPECTED BY IBWENKE WORK CENTER 41A SUPERVISOR EMKIGER STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN FUEL PUMP SWP4826 Figure 16-108: Major Engine Inspection (Fix Phase Removal and Replacement of a Repairable Component) 16-236 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT

TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 235DA00 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96105 14386 9313 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 123456-1 96105 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96105 0800 C1451 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY TIME/CYCLES TIME/CYCLES TIME/CYCLES FUEL PUMP LEAKING PILOT/INITIATOR AD1SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL

NUMBER ORG DAY SER SUF AC3104A02 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6105DZ33 SYSTEM/REASON MCN FUEL PUMP LK SWP4826 Figure 16-109: Major Engine Inspection (Component Turn-In) 16-237 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JRASHBY ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 0301200 D98 11 2 0 000 01 0.0 0.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHHA 663223 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL

NUMBER 0800 96104 0800 IN WORK 96104 1300 96120 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY PERFORM 1200 HR MAJOR PILOT/INITIATOR IW 96104 0800 M3 96104 1400 INSP PER MRCs AD3 SMITH IW 96120 0800 JC 96120 1300 CORRECTIVE ACTION COMPLETED 1200 HR MAJOR INSP CF QA REQ REQ CORRECTED BY JHDAY JOB CONTROL NUMBER ORG DAY SER SUF AC3104A00 INSPECTED BY KRGNADT WORK CENTER 41A SUPERVISOR IMMORRIS STATUS INSPT JCN A00 MAINT CONTROL BNPOWELL PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN 663223 INSP SWP4826 Figure 16-110: Major Engine Inspection Completed After Repair Action 16-238 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS

LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0121 00 22300 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 650403 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 77445 650403 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8C 96156 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY COMPLY WITH J52 PPB # 121 PILOT/INITIATOR AZ1SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88156107 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN

SYSTEM/REASON MCN PPB # 121 SWP4826 Figure 16-111: Supply Asset (TD Compliance Request) 16-239 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 96156 1030 3 0.1 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0121 00 D98 41 2 22300 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 650403 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1030 96156 1030 77445 650403 IN WORK 96156 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART

NUMBER J52-P-8C 96156 M3 0.1 TIME/CYCLES TIME/CYCLES E2378 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96156 1030 DISCREPANCY COMPLY WITH J52 PPB # 121 PILOT/INITIATOR 96156 1030 IW AZ1SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88156107 WORK CENTER 41A STATUS INSPT JCN PRI TURN-IN DDSN 3 SYSTEM/REASON MCN PPB # 121 SWP4826 Figure 16-112: Supply Asset TD Compliance Request (IMA Production Control Entries) 16-240 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE SMITH 1 S9841A4 RAS 96156 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM

PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0121 00 D98 41 2 C 01 1.0 1.0 22300 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 650403 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 1030 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96156 1030 77445 650403 IN WORK 96156 1130 96156 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8C 96156 E2378 TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96156 1030 DISCREPANCY COMPLY WITH PPB #121 IW 96156 1030 JC 96156 1130 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AZ1 SMITH CORRECTIVE ACTION COMPLIED WITH PPB #121 CF QA REQ REQ CORRECTED BY JHSMITH INSPECTED BY IMJONES JOB CONTROL NUMBER ORG DAY SER SUF D88156107 WORK CENTER 41A SUPERVISOR RASEWEL STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3

BCM SYSTEM/REASON MCN PPB #121 SWP4826 Figure 16-113: Supply Asset (TD Compliance Completed) 16-241 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER WORK ACT MAL UNIT CD ORG TRANS M/L A/T CODE I/P HOURS TYPE EQUIP FID BU/SER NUMBER W/D T/M POSIT EMT SFTY/EI TIME/CYCLES TIME/CYCLES TIME/CYCLES REQ NO TECHNICAL DIRECTIVE ID INT CODE BASIC NO RV AM METER REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM RECD FSCM SERIAL NUMBER IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC DATE ORD DATE REC PART KIT SE FSCM TECH INV CD PERM CD INSTALLED/NEW ITEM FSCM SERIAL

NUMBER PART NUMBER TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY PILOT/INITIATOR CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON Figure 16-114: O-Level Engine TD Compliance Request 16-242 BCM MCN COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MARCH 1 D9841A14 RAD 96206 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0154 02 00 D98 41 2 C 01 1.5 1.5 2351P TYPE BU/SER EQUIP

NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 664551 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1030 96206 1030 77445 664551 IN WORK 96206 1200 96206 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8C 96206 TIME/CYCLES TIME/CYCLES E1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96206 1030 DISCREPANCY COMPLY WITH PART II OF PPB #154 PILOT/INITIATOR 96206 1030 IW 96206 1200 JC AD2 DEAN CORRECTIVE ACTION COMPLIED WITH PPB #154 PART II CF QA REQ REQ CORRECTED BY JHMARCH JOB CONTROL NUMBER ORG DAY SER SUF AC3206178 INSPECTED BY IMCLARK WORK CENTER 41A SUPERVISOR RADAVIS STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN PPB 154 SWP4826 Figure 16-115: O-Level Engine TD Compliance Request (Production Control Entries) 16-243 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826

VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MARCH 1 D9841A14 RAD 96206 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0154 02 00 D98 41 2 C 01 1.5 1.5 2351P TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHMA 664551 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1030 96206 1030 77445 664551 IN WORK 96206 1200 96206 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER J52-P-8C 96206 TIME/CYCLES TIME/CYCLES E1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME

EOC TIME/CYCLES TIME/CYCLES M3 96206 1030 DISCREPANCY COMPLY WITH PART II OF PPB #154 PILOT/INITIATOR 96206 1030 IW 96206 1200 JC AD2 DEAN CORRECTIVE ACTION COMPLIED WITH PPB #154 PART II CF QA REQ REQ CORRECTED BY JHMARCH INSPECTED BY IMCLARK JOB CONTROL NUMBER ORG DAY SER SUF AC3206178 WORK CENTER 41A SUPERVISOR RADAVIS STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN PPB 154 SWP4826 Figure 16-116: O-Level Engine TD Compliance Request (Completed) 16-244 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MYERS/KOONS 1 D9841A6 LLM 96355 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM 77200 PART NUMBER FSCM 77200 PART NUMBER FSCM 77200 PART NUMBER 00003 ZQ9 02-14516 00003 ZQ9

MS20470AD3-3 00003 ZQ9 02-14548 DATE ORD REQ NO 03 96355 6355D048 03 96355 6355D049 03 96355 6355D050 DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0120 01 00 47 2 235DA00 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96355 0800 77200 F602 IN WORK 96355 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 023830-060-03 96355 TIME/CYCLES TIME/CYCLES C1839 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96355 0800 DISCREPANCY COMPLY WITH J52 PPC #120 PILOT/INITIATOR 96355 0800 IW AD2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF D88355163 WORK CENTER 41A STATUS INSPT JCN PRI TURN-IN

DDSN 3 SYSTEM/REASON MCN PPC120 SWP4826 Figure 16-117: I-Level Originated TD Compliance Request (Engine Component) 16-245 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE MYERS/KOONS 1 D9841A6 GSS 96355 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM 77200 PART NUMBER FSCM 77200 PART NUMBER FSCM 77200 PART NUMBER 00003 ZQ9 02-14516 00006 ZQ9 MS20470AD3-3 00003 ZQ9 02-14548 DATE ORD REQ NO DATE REC 03 96355 6355D048 96355 03 96355 6355D049 96355 03 96355 6355D050 96355 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0120 01 00 47 2 C 01 2.0 1.0 235DA00 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV

CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96355 0800 77200 F602 77200 F602 IN WORK 96355 0900 96355 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 023830-060-03 96355 023830-060-04 TIME/CYCLES TIME/CYCLES C1839 C1839 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96355 0800 DISCREPANCY COMPLY WITH J52 PPC #120 PILOT/INITIATOR 96355 0800 IW 96355 0900 JC CPL SMITH CORRECTIVE ACTION COMPLIED WITH J52 PPC #120 PART I CF QA REQ REQ CORRECTED BY ABKOONS INSPECTED BY GSSLANTIS JOB CONTROL NUMBER ORG DAY SER SUF D88355163 WORK CENTER 41A SUPERVISOR GSROY STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN PPC120 SWP4826 Figure 16-118: I-Level Originated TD Compliance (Completed) 16-246 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES

REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0050 00 1 235D800 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 73030 768-48 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 707675L57 96163 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY AMEND 1 C0502 TIME/CYCLES TIME/CYCLES TIME/CYCLES COMPLY WITH PARA OF PPC #50 PILOT/INITIATOR CPL SMITH CORRECTIVE ACTION CF QA REQ

REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3156178 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN SYSTEM/REASON MCN PPC50 AM1 SWP4826 Figure 16-119: O-Level Request for TD Compliance Assist (Engine Component) 16-247 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 96163 0800 3 0.1 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0050 00 47 2 1 235D800 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME

EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96163 0800 73030 768-48 IN WORK 96163 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 707675L57 96163 M3 0.1 C0502 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96163 0800 DISCREPANCY COMPLY WITH PARA OF PPC #50 PILOT/INITIATOR IW 96163 0800 AMEND 1 AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF AC3156178 WORK CENTER 411 STATUS INSPT JCN PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN PPC50 AM1 SWP4826 Figure 16-120: O-Level Request for TD Compliance Assist (AMSU/Production Control Entries) 16-248 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BROWN/PINNO 1 D984118

RSS 96163 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 235D800 D98 02 0050 1 00 47 2 A 00 2.0 1.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96163 0800 0800 73030 768-48 73030 768-48 IN WORK 96163 96163 0900 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 707675L57 96163 707675L57 TIME/CYCLES TIME/CYCLES C0502 C0502 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96163 0800 DISCREPANCY COMPLY WITH PARA II OF PPC #50 PILOT/INITIATOR IW 96163 0800 JC 96163 0900

AMEND 1 AZ3 SMITH CORRECTIVE ACTION COMPLIED WITH PPC #50 AMEND 1 PARA II CF QA REQ REQ CORRECTED BY ABBROWN JOB CONTROL NUMBER ORG DAY SER SUF AC3156178 INSPECTED BY GSSAUCIER WORK CENTER 411 SUPERVISOR GSSAUCIER STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN PPC 50 AM1 SWP4826 Figure 16-121: O-Level Request for TD Compliance Assist (Completed) 16-249 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 27400 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID

SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 A B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER TXAA1 310021 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96110 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES E1234 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY ENGINE (HPC MODULE) FODDED. FOR INSP USE PE4110B00 PILOT/INITIATOR AZ1 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4110110 WORK CENTER STATUS INSPT JCN B00 PRI TURN-IN DDSN 6110G265 SYSTEM/REASON MCN HPC MOD FOD SWP4826 Figure 16-122: O-Level Turn-In Control Document for Engine Repair (Modular Engine) 16-250 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT

TOOLBOX/INT DATE RAY 1 D9841U28 ALC 96110 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 11 2 C 160 01 0.5 0.5 27473 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 W 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 IN WORK 96110 0830 96110 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96110 0800 DISCREPANCY FUEL PUMP HAS BROKEN LEAD PILOT/INITIATOR 96110 0800 IW 96110 0830 JC AD1 DEAN CORRECTIVE ACTION REPAIRED BROKEN

LEAD CF QA REQ REQ CORRECTED BY JHRAY JOB CONTROL NUMBER ORG DAY SER SUF PE4110110 INSPECTED BY ALCOLVIN WORK CENTER 41U SUPERVISOR ALCOLVIN STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN FUEL PUMP SWP4826 Figure 16-123: Fix-In-Place (Not Requiring Material) 16-251 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BICE 1 D9841U4 RIC 96110 BICE 1 D9841U6 RIC 96112 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 1.0 LOCAL USE REFERENCE INDEX H F/P AWP X FSCM 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R 070 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 4064T35607 ZQ9 03 DATE ORD 96110 REQ NO DATE REC 6110DZ38 96112 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 12

2 C 070 01 2.0 2.0 2747H TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 W 3 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 IN WORK 96110 0900 96112 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96110 0800 DISCREPANCY FUEL INLET TUBE ASSY BROKEN PILOT/INITIATOR 96110 0800 IW 96110 0900 WP AD3 DEAN 96112 0800 IW JC 96112 0900 CORRECTIVE ACTION REPLACED FUEL INLET TUBE ASSY CF QA REQ REQ CORRECTED BY JHBICE JOB CONTROL NUMBER ORG DAY SER SUF PE4110110 INSPECTED BY IMCOX WORK CENTER 41U SUPERVISOR IMCOX STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN FUEL TUBE SWP4826 Figure 16-124: Fix-In-Place (Requiring Material) 16-252 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN

SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE WILSON 1 D9841U5 TLK 96110 WILSON 1 D9841U4 TLK 96111 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.5 0.5 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 4064T97G03 ZQ9 03 DATE ORD 96110 REQ NO DATE REC 4110DZ29 96111 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 23 2 R 381 01 1.0 1.0 27473 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 W 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 99207 17 99207 16 IN WORK 96110 0830 96111 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4064T97G03

96110 4064T97G03 C0154 TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES M3 96110 0800 DISCREPANCY FUEL PUMP LEAKING IW 96110 0800 WP 96110 0830 IW 96111 0800 JC 96111 0830 CORRECTIVE ACTION R & R FUEL PUMP TIME/CYCLES TIME/CYCLES TIME/CYCLES C0012 PILOT/INITIATOR AD3 DEAN CF QA REQ REQ CORRECTED BY JHWILSON JOB CONTROL NUMBER ORG DAY SER SUF PE41101101A INSPECTED BY IMBELL WORK CENTER 41U SUPERVISOR TLKEYS MAINT CONTROL IBMOSHER INSPT STATUS JCN PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN FUEL PUMP SWP4826 Figure 16-125: Removal/Replacement of a Repairable Subassembly with No Repairable SubSubassemblies 16-253 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE KILSO/FISHER 1 D9841U10 TLK 96110 KILSO/FISHER 1 D9841U2 TLK 96114 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0

4.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 6046T13G01 ZQ9 03 DATE ORD 96110 REQ NO 4110DZ87 DATE REC 96114 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 23 2 R 301 01 8.0 4.0 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 99207 317031 99207 317021 IN WORK 96110 1000 96114 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6046T13G01 96110 6046T13G01 TIME/CYCLES TIME/CYCLES C0645 C0001 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96110 0800 DISCREPANCY HPC MODULE HAS COMPRESSOR PILOT/INITIATOR 96110 0800 IW 96110 1000 WP ROTOR ASSY DAMAGED

AD3 DEAN 96114 0800 IW JC 96114 1000 CORRECTIVE ACTION R & R HPC MODULE CF QA REQ REQ CORRECTED BY JHSMITH JOB CONTROL NUMBER ORG DAY SER SUF PE4110110A INSPECTED BY IMROY WORK CENTER 41U SUPERVISOR TLROLLINS STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN HPC MODULE SWP4826 Figure 16-126: Removal/Replacement of a Repairable Module/Component with Repairable SubSubassemblies 16-254 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JBASHBY ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 31

2 C 301 01 0.0 0.0 27400 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 A B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 TXAA1 310021 IN WORK 96110 1000 96116 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96110 TIME/CYCLES TIME/CYCLES E1234 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96110 0800 DISCREPANCY ENGINE (HPC MODULE) FODDED. PILOT/INITIATOR 96110 0800 IW 96110 1200 M3 FOR INSP USE JCN PE4110B00 AD3 SMITH 96116 0800 IW JC 96116 1000 CORRECTIVE ACTION REPAIRED FODDED ENGINE BY REPLACEMENT OF HPC MODULE. TEST CELL TIME 16 HRS CORRECTED BY JHROY INSPECTED BY IBCOX JOB CONTROL NUMBER ORG DAY SER SUF PE4110110 WORK CENTER 41U SUPERVISOR RIMULLEN STATUS INSPT JCN B00 MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6110G265 SYSTEM/REASON MCN 310021 MOM SWP4826 Figure 16-127: Engine

Repair Control Document (Completed) 16-255 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 301 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1000 96110 99207 317021 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6046T13G01 96110 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1

96110 1000 TIME/CYCLES TIME/CYCLES TIME/CYCLES C0645 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY HPC MODULE HAS COMPRESSOR ROTOR ASSY DAMAGED PILOT/INITIATOR AD2 DEAN CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4411011A WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6112DZ87 SYSTEM/REASON MCN 317021 MOM SWP4826 Figure 16-128: Turn-In of Repairable Module with Repairable Sub-Subassemblies 16-256 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL 1 D9841U7 AFS 96112 MORSE 1 D9841U9 AFS 96115 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 4.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001

6027T11G04 ZQ9 03 DATE ORD 96112 REQ NO DATE REC 6112DZ38 96115 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 23 2 R 301 01 8.0 8.0 2742200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96112 0800 99207 OK2232 99207 OK2211 IN WORK 96112 1200 96115 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6027T11G04 96112 6027T11G04 TIME/CYCLES TIME/CYCLES C0395 C0001 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96112 0800 DISCREPANCY HPC COMPRESSOR ROTOR PILOT/INITIATOR 96112 0800 IW 96112 1200 WP SUBASSEMBLY DAMAGED AD3 DEAN 96115 0800 IW JC 96115 1200 CORRECTIVE ACTION R & R HPC COMPRESSOR ROTOR ASSY CF QA REQ REQ CORRECTED BY NNMORSE JOB CONTROL NUMBER ORG DAY SER SUF PE4110110AA

INSPECTED BY AFSMITH WORK CENTER 41U SUPERVISOR AFSMITH STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN ROTOR ASSY SWP4826 Figure 16-129: Removal/Replacement of a Repairable Sub-Subassembly from a Module 16-257 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BRUSH KRL 96112 1 D9841U7 COLTON 1 D9841U9 KRL 96116 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 96112 0830 3 95.5 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 27420 D98 31 2 C 301 01 2.0 1.0 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV

CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1000 96110 0800 99207 317021 IN WORK 96112 1000 96116 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6046T13G01 96112 M3 95.5 TIME/CYCLES TIME/CYCLES C0645 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96110 1000 DISCREPANCY HPC MODULE HAS COMPRESSOR PILOT/INITIATOR 96112 0800 M3 96112 0800 IW ROTOR ASSY DAMAGED AD3 SMITH 96112 0830 M3 IW 96116 0800 CORRECTIVE ACTION REPAIRED DAMAGE BY R & RING HPC JC 96116 0830 COMPRESSOR ROTOR ASSY CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM JHCOLTON IBJAMES KRLOWE ECMERCER JOB CONTROL NUMBER ORG DAY SER SUF PE4110110A WORK CENTER 41U STATUS INSPT JCN PRI TURN-IN DDSN 3 6110DZ87 Figure 16-130: Module Repair (Completed) 16-258 SYSTEM/REASON MCN 317021 MOM SWP4826 COMNAVAIRFORINST 4790.2C 15 Jan 2017

N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 301 2742200 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96112 99207 OK2211 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6027T11G04 96112 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96112 1200 TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES C0395 DISCREPANCY HPC

COMPRESSOR ROTOR SUBASSEMBLY DAMAGED PILOT/INITIATOR AD3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4110110AA WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 4112DZ38 SYSTEM/REASON MCN ROTOR ASSY SWP4826 Figure 16-131: Turn-In of Repairable Sub-Subassembly from a Repairable Component 16-259 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL/MORSE 1 D984114 KRB 96114 POWELL/MORSE 1 D984114 KRB 96116 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 3.0 LOCAL USE REFERENCE INDEX H F/P AWP X X FSCM 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R 301 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 4062T15P01 ZQ9 03 DATE ORD 96114 REQ NO 6114D268 DATE REC 96116 WORK ACT MAL TECHNICAL

DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 301 01 6.0 3.0 2742200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96112 0800 99207 OK2211 IN WORK 96114 1030 96116 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6027T11G04 96112 TIME/CYCLES TIME/CYCLES C0395 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96112 1200 DISCREPANCY HPC COMPRESSOR ROTOR PILOT/INITIATOR 96114 0800 M3 96114 0800 IW SUBASSEMBLY DAMAGED AD2 DEAN 96114 0930 WP IW 96116 0900 CORRECTIVE ACTION REPAIRED HPC COMPRESSOR ROTOR ASSY JC 96116 1030 BY REPLACING SPOOL COMP STAGES 1-2 CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL X RFI BCM BNPOWELL KRBOOTH DLJONES RBARGY JOB CONTROL NUMBER ORG DAY SER SUF PE4110110AA

WORK CENTER 411 STATUS INSPT JCN PRI TURN-IN DDSN 3 4112DZ38 SYSTEM/REASON MCN ROTOR ASSY SWP4826 Figure 16-132: Repair of a Repairable Component with Required Material 16-260 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 301 2742220 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96114 99207 TG3718 IN WORK COMP DATE AWAITING

MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4062T15P01 96114 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96114 1200 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY C0227 TIME/CYCLES TIME/CYCLES TIME/CYCLES SPOOL COMP STAGE 1-2 F0DDED PILOT/INITIATOR AD3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4411011AB WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6114D268 SYSTEM/REASON MCN SPOOL COMP SWP4826 Figure 16-133: Turn-In of a Repairable Component Sub-Subassemblies 16-261 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL/MORSE 1 D984116 KRB 96114 POWELL/MORSE 1 D984115 KRB 96116 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 2.0 96114 1500 3 1.0 2.0 LOCAL USE REFERENCE INDEX H I F/P AWP X X FSCM 99207 X X

FSCM 99207 FSCM A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R 301 PART NUMBER R 301 PART NUMBER DATE ORD REQ NO DATE REC 00016 6026T26P03 ZQ9 03 96114 6114D096 96116 00017 6024T30P03 ZQ9 03 96114 6114D097 96116 PART NUMBER WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 C 301 01 4.0 2.0 2742200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 1200 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96114 1600 99207 TG3718 IN WORK 96114 1000 96116 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4062T15P01 96114 M3 1.0 C0227 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES A1 96114 1200 DISCREPANCY SPOOL COMP STAGES 1-2 FODDED PILOT/INITIATOR M3 96114 1500 IW 96114 1600 AD3 SMITH WP 96114

1700 IW 96116 0900 CORRECTIVE ACTION R & RD 16 BLADES ON SPOOL STAGE 1 AND JC 96116 1000 17 BLADES ON STAGE 2 CORRECTED BY BNPOWELL JOB CONTROL NUMBER ORG DAY SER SUF PE4110110AB INSPECTED BY CVSNYDER WORK CENTER 411 SUPERVISOR ALMARTIN STATUS INSPT JCN MAINT CONTROL DLJONES PRI TURN-IN DDSN 6114D268 3 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN SPOOL COMP SWP4826 Figure 16-134: Repair of a Sub-Subassembly from a Component Subassembly (Completed) 16-262 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL 1 D9841U7 AFS 96152 MORSE 1 D9841U9 AFS 96153 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 4.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 6027T11G04 ZQ9 03 DATE ORD 96152 REQ

NO DATE REC 6152DZ38 96153 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 32 2 R 301 01 8.0 8.0 2742200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1300 96152 1300 99207 OK2232 99207 OK2211 IN WORK 96152 1200 96153 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6027T11G04 96152 6027T11G04 TIME/CYCLES TIME/CYCLES C0395 C0001 MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96152 1300 DISCREPANCY HPC COMPRESSOR ROTOR PILOT/INITIATOR 96152 1300 WP 96152 1700 IW SUBASSEMBLY DAMAGED AD3 DEAN 96153 0800 IW JC 96153 1200 CORRECTIVE ACTION R & RD HPC COMPRESSOR ROTOR ASSY CF QA REQ REQ CORRECTED BY NNMORSE JOB CONTROL NUMBER ORG DAY SER SUF PE4150C02A INSPECTED BY AFSMITH WORK CENTER 41U

SUPERVISOR AFSMITH STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 RFI SYSTEM/REASON MCN ROTOR ASSY SWP4826 Figure 16-135: Removal/Replacement of a Repairable Sub-Subassembly from a Module 16-263 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 301 2742200 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 W 1 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1700 96152 99207

OK2211 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6027T11G04 96152 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96152 1700 TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES TIME/CYCLES C0395 DISCREPANCY HPC COMPRESSOR ROTOR SUBASSEMBLY DAMAGED PILOT/INITIATOR AD3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4150C02A WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6152DZ38 SYSTEM/REASON MCN ROTOR ASSY SWP4826 Figure 16-136: Turn-In of a Repairable Sub-Subassembly from a Module 16-264 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART

NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 0300200 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 310021 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER TXAA1 310021 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96150 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY E2345 TIME/CYCLES TIME/CYCLES TIME/CYCLES PERFORM 200 HR MAJOR INSP PILOT/INITIATOR AZ3 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4150C00 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6115G243 SYSTEM/REASON MCN 310021 MOM SWP4826 Figure 16-137: O-Level Turn-In Control Document Modular Engine Turn-In

(Solely for Major Engine Inspection) 16-265 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE LANDON/STANLEY 1 D9841U3 ICC 96150 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 8.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 2 0 000 00 8.0 4.0 0300200 D89 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0900 96150 0900 IN WORK 96150 1300 96150 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER

TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96150 0900 DISCREPANCY COMPLY WITH MRCs 6, 9, 13, AND 15 PILOT/INITIATOR 96150 0900 IW 96150 1300 JC CPL STEELE CORRECTIVE ACTION COMPLETED CARDS 6, 9, 13 AND 15 CF QA REQ REQ CORRECTED BY JHLANDON JOB CONTROL NUMBER ORG DAY SER SUF PE4150C00 INSPECTED BY ICCOLVIN WORK CENTER 41U SUPERVISOR ICCOLVIN STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN 310021 LOOK SWP4826 Figure 16-138: Major Modular Engine Inspection (Look Phase Supporting Work Center) 16-266 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE TRACY/WILLIS 1 D984503 IMJ 96154 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 96154 0800 8 101.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED /

REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 11 2 0 000 00 4.0 2.0 0300200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96150 1300 IN WORK 96154 1500 96154 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M8 101.0 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M8 96150 0800 DISCREPANCY COMPLY WITH MRCs 16 AND 17 PILOT/INITIATOR 96154 1300 IW 96154 1500 JC ENGINE TEST CELL RUN CARDS CPL STEELE CORRECTIVE ACTION COMPLETED CARDS 16 AND 17 ENGINE RAN GOOD. TEST CELL TIME 19 HOURS CORRECTED BY JHWILLIS JOB CONTROL NUMBER ORG DAY SER SUF

PE4150C00 INSPECTED BY KRDEVALL WORK CENTER 450 SUPERVISOR IMJONES STATUS INSPT JCN C00 CF QA REQ REQ MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN 310021 RUN SWP4826 Figure 16-139: Major Modular Engine Inspection (Look Phase Supporting Work Center) (Engine Test Cell Run) 16-267 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE HARPER 1 D9841U12 PSC 96151 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 0.3 LOCAL USE REFERENCE INDEX H F/P AWP X FSCM 12345 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI R 381 PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC 00001 987654-3 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 12 2 C 381 01 0.3 0.3 2747G TYPE BU/SER EQUIP NUMBER W/D T/M

POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 W 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96151 0800 IN WORK 96151 0815 96151 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96151 0800 DISCREPANCY ENGINE OIL TANK HAS SMALL PILOT/INITIATOR 96151 0800 IW 96151 0815 JC LEAK AT BOLT AD1 DEAN CORRECTIVE ACTION REPLACED GASKET UNDER BOLT. FIXED LEAK CF QA REQ REQ CORRECTED BY JHHARPER JOB CONTROL NUMBER ORG DAY SER SUF PE4150C01 INSPECTED BY PSCROOK WORK CENTER 41U SUPERVISOR PSCROOK STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN OIL TANK SWP4826 Figure 16-140: Major Engine Inspection (Fix-In-Place) 16-268 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED

SIGNATURE NONE LOGS REC X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE BALL 1 D9841U3 RIP 96151 BOX 1 D9841U5 RIP 96153 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 4.0 4.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 6046T12G01 ZQ9 03 DATE ORD 96151 REQ NO 6151D279 DATE REC 96153 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 23 2 R 780 01 8.0 8.0 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96151 0800 99207 317033 99207 317021 IN WORK 96151 1200 96153 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6046T12G01 96151 6046T12G01 TIME/CYCLES TIME/CYCLES C1787 C0001

MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96151 0800 DISCREPANCY HPC MODULE IS WARPED PILOT/INITIATOR 96151 0800 IW 96151 1200 WP AD1 DEAN 96153 0800 IW JC 96153 1200 CORRECTIVE ACTION R & Rd HPC MODULE CF QA REQ REQ CORRECTED BY JHBALL JOB CONTROL NUMBER ORG DAY SER SUF PE4150C02 INSPECTED BY ACFLETCHER WORK CENTER 41U SUPERVISOR RIPOWELL STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN R/R HPC MOD SWP4826 Figure 16-141: Major Engine Inspection (Fix Phase Module Replacement) 16-269 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE

ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317021 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 1200 96151 99207 317021 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6046T12G01 96151 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96151 1200 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY C1787 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AD3 SMITH HPC MODULE IS WARPED CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4150C02 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6151D279 SYSTEM/REASON MCN HPC MODULE SWP4826 Figure 16-142: Major Engine Inspection (Module Turn-In) 16-270 BCM COMNAVAIRFORINST 4790.2C

15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE HURD 1 D9841U10 TLR 96152 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 99207 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 4064T97G03 ZQ9 03 DATE ORD 96152 REQ NO 6152D222 DATE REC 96152 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 23 2 R 381 01 1.0 1.0 27473 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96152 0800 99207 500148 99207 500166 IN WORK 96152 0900 96152 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4064T97G03

96152 4064T97G03 C1287 C0725 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96152 0800 MAIN FUEL PUMP LEAKING DISCREPANCY PILOT/INITIATOR IW 96152 0800 JC 96152 0900 AD3 DEAN CORRECTIVE ACTION R & Rd FUEL PUMP CF QA REQ REQ CORRECTED BY JHHURD JOB CONTROL NUMBER ORG DAY SER SUF PE4150C03 INSPECTED BY TLRAY WORK CENTER 41U SUPERVISOR TLRAY STATUS INSPT JCN MAINT CONTROL IBMOSHER PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN FUEL PUMP SWP4826 Figure 16-143: Major Engine Inspection (Fix Phase Repairable Component Replacement) 16-271 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART

NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 27473 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 M 2 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0830 96152 99207 500166 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 4064T97G03 96152 MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC A1 96152 0830 TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY C1287 TIME/CYCLES TIME/CYCLES TIME/CYCLES PILOT/INITIATOR AD3 DEAN MAIN FUEL PUMP LEAKING CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4150C03 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN 6152D222 SYSTEM/REASON MCN FUEL PUMP LK SWP4826 Figure 16-144: Major Engine Inspection (Fix Phase Component

Turn-In) 16-272 BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X BNPOWELL ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 31 2 0 000 01 0.0 0.0 0300200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAA 310021 O J REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96150 0800 TXAA1 310021 IN WORK 96150 1600 96154 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 96150 TIME/CYCLES TIME/CYCLES E2345 MAINTENANCE/SUPPLY

REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96150 0800 DISCREPANCY PERFORM 200 HR MAJOR INSP PILOT/INITIATOR 96150 0800 IW 96150 1600 M3 AZ2 SMITH 96154 0800 IW JC 96154 1600 CORRECTIVE ACTION COMPLETED 200 HR MAJOR INSP CORRECTED BY JHMEYERS JOB CONTROL NUMBER ORG DAY SER SUF PE4150C00 INSPECTED BY RALOFTIS WORK CENTER 41U SUPERVISOR RALOFTIS STATUS INSPT JCN MAINT CONTROL ECMERCER PRI TURN-IN DDSN 3 6150G243 CF QA REQ REQ X RFI BCM SYSTEM/REASON MCN 310021 MOM SWP4826 Figure 16-145: Completed Major Inspection Control Document (Modular Engine Turned-In Solely for Major Inspection) 16-273 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART

NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 27420 A 02 0022 A1 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317045 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER MAINTENANCE/SUPPLY REC STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES TIME/CYCLES DISCREPANCY PSSN 310026 TIME/CYCLES TIME/CYCLES TIME/CYCLES COMPLY WITH F404 PPC #22 REV A PILOT/INITIATOR AZ2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4104110 WORK CENTER STATUS INSPT JCN PRI TURN-IN DDSN BCM SYSTEM/REASON MCN PPC 22 REV A SWP4826 Figure 16-146: O-Level Activity Request for a Modular Engine TD Compliance by

I-Level Activity 16-274 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X ACCUMULATED WORK HOURS NAME/SHIFT TOOLBOX/INT MAN DATE ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0022 A1 D98 41 2 A 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317045 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96104 IN WORK COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER M3 0.0 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC

TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY COMPLY WITH F404 PPC #22 REV A PILOT/INITIATOR PSSN 310026 AZ2 SMITH CORRECTIVE ACTION CF QA REQ REQ CORRECTED BY INSPECTED BY SUPERVISOR MAINT CONTROL RFI JOB CONTROL NUMBER ORG DAY SER SUF PE4104110 WORK CENTER 41U STATUS UP INSPT JCN PRI TURN-IN DDSN 3 BCM SYSTEM/REASON MCN PPC 22 REV A SWP4826 Figure 16-147: Production Control Entries (O-Level Activity Request for TD Compliance) 16-275 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X TNBOLYARD ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE DAVIS 1 D9841U11 THT 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE

I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0022 A A1 D98 41 2 C 01 1.5 1.5 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 317045 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 IN WORK 96104 0930 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 DISCREPANCY COMPLY WITH F404 PPC #22 REV A PILOT/INITIATOR IW 96104 0800 JC 96104 0930 PSSN 310026 AMCS KOVICH CORRECTIVE ACTION INCORPORATED PPC #22 REV A CF QA REQ REQ CORRECTED BY JHDAVIS JOB CONTROL NUMBER ORG DAY SER SUF PE4104110 INSPECTED BY IMJONES WORK CENTER 41U SUPERVISOR JBLOWE STATUS UP INSPT JCN MAINT CONTROL MTMCKEEN PRI TURN-IN DDSN 3 RFI BCM SYSTEM/REASON MCN PPC 22 REV A SWP4826 Figure 16-148: Completed TD Compliance (Applies to a Module

With No Module or Repairable Component P/N Change) 16-276 COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE WILCOX 1 D9841U3 RIC 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 02 0106 01 D98 47 2 C 01 1.5 0.5 27420 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD TXAX 312021 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 99207 312021 99207 312021 IN WORK 96104 0930 96104 COMP DATE AWAITING MAINTENANCE HRS PART

NUMBER REMOVED PART NUMBER 6046T11G01 96104 6046T11G01-1 E1421 E1421 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 COMPLY WITH PPC #`06 PPSN 310026 PILOT/INITIATOR DISCREPANCY IW 96104 0800 JC 96104 0930 AZ3 SMITH CORRECTIVE ACTION COMPLIED WITH PPC #106 CORRECTED BY ABWILCOX JOB CONTROL NUMBER ORG DAY SER SUF PE4104110 INSPECTED BY GSMURRY WORK CENTER 41U SUPERVISOR RICLAUSEN STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 SYSTEM/REASON MCN PPC106 SWP4826 Figure 16-149: TD Compliance (Applies to a Module With P/N Change) 16-277 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AJSTYLES ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE WILCOX 1 D9841U6 RIC 96104 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.5 LOCAL USE REFERENCE INDEX F/P AWP A/T

FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT 01 0008 B 00 47 2 C 01 1.5 1.5 2742200 D98 TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YEAA 000000 REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0800 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 96104 0800 06858 AF0034 06858 AF0034 IN WORK 96104 0900 96104 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 6050T12G001 96104 6050T12G001 C1086 C1086 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96104 0800 COMPLY WITH PPB #8 REV B DISCREPANCY PILOT/INITIATOR IW 96104 0800 JC 96104 0900 PPSN 310026 AZ3 SMITH CORRECTIVE ACTION COMPLIED WITH PPB #8 REV B CORRECTED BY ABWILCOX JOB CONTROL NUMBER ORG

DAY SER SUF PE4104110 INSPECTED BY GSMURRY WORK CENTER 41U SUPERVISOR RICLAUSEN STATUS UP INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 3 SYSTEM/REASON MCN PPB 8 REV B SWP4826 Figure 16-150: TD Compliance (Applies to a Component Within A Module) 16-278 CF QA REQ REQ X RFI BCM COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X JWABBOTT ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE POWELL 1 D9841U3 KLD 96110 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 3.0 LOCAL USE REFERENCE INDEX F/P FSCM AWP 77200 A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI PART NUMBER FSCM PART NUMBER FSCM PART NUMBER 00001 70065OL88 AK0 03 DATE ORD 96110 REQ NO 6110G124 DATE REC 96110 WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT D98 18 2 T 813 01 3.0 3.0 23561 TYPE BU/SER EQUIP NUMBER W/D T/M

POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD JHDX 661091 O B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0800 96110 0800 77200 35719 77200 38407 IN WORK 96110 1100 96110 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 70065OL88 96110 70065OL88 C0820 C0940 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96110 0800 CANNIBALIZATION OF MAIN FUEL DISCREPANCY PILOT/INITIATOR IW 96110 0800 JC 96110 1100 CONTROL FROM ENG 661091 FOR SQD NMCS AFCM ROBINSON REQ 6110-G124 VA-35 CORRECTIVE ACTION R & Rd FUEL CONTROL AS DIRECTED CF QA REQ REQ CORRECTED BY BNPOWELL JOB CONTROL NUMBER ORG DAY SER SUF D88110124 INSPECTED BY MFBARBOUR WORK CENTER 41A SUPERVISOR JJONES STATUS INSPT JCN MAINT CONTROL IBMERCER PRI TURN-IN DDSN 1 BCM SYSTEM/REASON MCN F/CONT CANN SWP4826 Figure 16-151: Engine or Module Cannibalization (For a Supported

Activity) 16-279 RFI COMNAVAIRFORINST 4790.2C 15 Jan 2017 N2R22502 MCN SWP4826 VIDS/MAF OPNAV 4790/60 (REV 2-82) ENTRIES REQUIRED SIGNATURE NONE LOGS REC X X AZ3 HAVENS ACCUMULATED WORK HOURS MAN NAME/SHIFT TOOLBOX/INT DATE ROY 1 GQ281A-1 KD 96350 ACCUMULATED AWM HOURS HOURS DATE TIME REASON HOURS 1.0 LOCAL USE REFERENCE INDEX F/P AWP A/T FAILED / REQUIRED MATERIAL MAL REF SYMBOL QTY PROJ PRI FSCM PART NUMBER FSCM PART NUMBER FSCM PART NUMBER DATE ORD REQ NO DATE REC WORK ACT MAL TECHNICAL DIRECTIVE ID UNIT CD ORG TRANS M/L A/T CODE I/P HOURS EMT INT CODE BASIC NO RV AM PART KIT GQ2 18 2 R 804 01 1.0 1.0 97A1J TYPE BU/SER EQUIP NUMBER W/D T/M POSIT FID SFTY/EI METER SE FSCM TECH INV CD PERM CD YPAA 000159 O B REPAIR CYCLE DATE TIME EOC REMOVED/OLD ITEM INSTALLED/NEW ITEM 0830 96350 RECD FSCM SERIAL NUMBER FSCM SERIAL NUMBER 0830 30003 2352 30003 7328 IN WORK 96350 96350 0930 COMP DATE AWAITING MAINTENANCE HRS PART NUMBER REMOVED PART NUMBER 1H86L001001 96350

1H90B008001 H0492 H1295 TIME/CYCLES TIME/CYCLES MAINTENANCE/SUPPLY REC TIME/CYCLES TIME/CYCLES STATUS DATE TIME EOC TIME/CYCLES TIME/CYCLES M3 96350 0830 REPLACE M284 DELAY CARTRIDGE DISCREPANCY PILOT/INITIATOR IW 96350 0830 JC 96350 0930 DUE TO HIGH TIME REQUIREMENT AECS WILLIAMS CORRECTIVE ACTION REMOVED AND REPLACED M248 NOMEN: DELAY CARTRIDGE P/N 2519704 LOC: PARACHUTE ASSY MFG: 02900 OPEN: 1295 INST: 1295 EXP 0497 CORRECTED BY AMEAN ROY JOB CONTROL NUMBER ORG DAY SER SUF GQ2091481 INSPECTED BY AME2 ABBOTT WORK CENTER 81A SUPERVISOR AME1 DRAKE STATUS DOWN INSPT JCN MAINT CONTROL AFCM ROBINSON PRI TURN-IN DDSN 3 CF QA REQ REQ RFI BCM SYSTEM/REASON MCN M284 SWP4826 Figure 16-152: Removal and Replacement of Cartridges, Cartridge Activated Devices, and Propellant Actuated Devices (I-Level Maintenance) 16-280